Jens Köhler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jens Köhler has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Berend Denkena
Institute of Production Engineering and Machine Tools, Leibniz Universität Hannover, 30823 Garbsen, Germany
3 shared publications B. Denkena
Leibniz Universität Hannover, Institute of Production Engineering and Machine Tools , Garbsen, Germany
2 shared publications- Anke Turger
Institute of Production Engineering and Machine Tools (IFW), Gottfried Wilhelm Leibniz Universität Hannover, An der Universität 2, 30823 Garbsen, Germany
1 shared publication - Christof Hurschler
Laboratory for Biomechanics and Biomaterials, Department of Orthopaedic Surgery, Hannover Medical School, Anna-von-Borries-Str. 1-7, 30625, Hannover, Germany
1 shared publication - Christoph Becher
Orthopädische Klinik der Medizinischen, Hochschule Hannover
1 shared publication - Friedrich Dinkelacker
Leibniz University Hannover
1 shared publication
Latest Publications
- 1 January 2014
- Published by Springer Nature
- p. 413-416
Drill Milling
- 1 March 2013
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 1 (1) , 011003
Efficient Machining of Microdimples for Friction Reduction
In order to improve the tribological properties of thermomechanically highly stressed surfaces such as cylinder liners, microdimples are produced by fly-cutting kinematics along the functional surface. The structures are used to hold back lubricant but also to increase the hydrodynamic pressure, which is built up between the sliding friction partners. For that, machining strategies for the pattern generation in cylindrical components are developed as well as a mathematical model of the microdimple arrangement and distribution. The tribological performance of the machined microdimples is analyzed by means of ring-on-disk experiments. At low sliding speeds the friction coefficient can be decreased clearly by microdimples. This indicates the potential for low-speed or reciprocating tribosystems like cylinder liners. This potential is quantified by motor driven experiments and the comparison between structured and nonstructured cylinder liners. A honed (fine) liner with additional microdimples along the interstice area shows friction losses up to 19% compared to standard honed nonstructured cylinder liner.
- 1 March 2013
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 1 (1) , 011003
Efficient Machining of Microdimples for Friction Reduction
In order to improve the tribological properties of thermomechanically highly stressed surfaces such as cylinder liners, microdimples are produced by fly-cutting kinematics along the functional surface. The structures are used to hold back lubricant but also to increase the hydrodynamic pressure, which is built up between the sliding friction partners. For that, machining strategies for the pattern generation in cylindrical components are developed as well as a mathematical model of the microdimple arrangement and distribution. The tribological performance of the machined microdimples is analyzed by means of ring-on-disk experiments. At low sliding speeds the friction coefficient can be decreased clearly by microdimples. This indicates the potential for low-speed or reciprocating tribosystems like cylinder liners. This potential is quantified by motor driven experiments and the comparison between structured and nonstructured cylinder liners. A honed (fine) liner with additional microdimples along the interstice area shows friction losses up to 19% compared to standard honed nonstructured cylinder liner.
- Open Access
- 1 January 2013
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 12 (1) , 84
Manufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants
Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices.
- 1 January 2013
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 12 (1) , 84
Open AccessManufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants
Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices.
- 28 June 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 58 (9-12) , 933-940
Influence of the tool corner radius on the tool wear and process forces during hard turning
- 28 June 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 58 (9-12) , 933-940
Influence of the tool corner radius on the tool wear and process forces during hard turning
- 8 December 2010
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 14 (4) , 455-470
CONSIDERATION OF THE FORM OF THE UNDEFORMED SECTION OF CUT IN THE CALCULATION OF MACHINING FORCES
For the calculation of machining forces in turning processes, the empirical equation of Victor and Kienzle has been established as a common model. However, the model has some constraints. The undeformed chip thickness has to be higher than 0.1 mm and the ratio of undeformed chip width and undeformed chip thickness has to be higher than four. This means that the equation cannot be used for several combinations of process parameters. This paper shows an approach to calculate the machining forces for any form of undeformed sections of cut based on the approach of Victor and Kienzle. In order to achieve this, the undeformed chip thickness and the undeformed chip width are defined in a new way. Furthermore, the direction of chip flow is considered to determine the feed and passive force components.
- 8 December 2010
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 14 (4) , 455-470
CONSIDERATION OF THE FORM OF THE UNDEFORMED SECTION OF CUT IN THE CALCULATION OF MACHINING FORCES
For the calculation of machining forces in turning processes, the empirical equation of Victor and Kienzle has been established as a common model. However, the model has some constraints. The undeformed chip thickness has to be higher than 0.1 mm and the ratio of undeformed chip width and undeformed chip thickness has to be higher than four. This means that the equation cannot be used for several combinations of process parameters. This paper shows an approach to calculate the machining forces for any form of undeformed sections of cut based on the approach of Victor and Kienzle. In order to achieve this, the undeformed chip thickness and the undeformed chip width are defined in a new way. Furthermore, the direction of chip flow is considered to determine the feed and passive force components.
- 4 May 2010
- Published by Springer Nature in Production Engineering
- Vol. 4 (5) , 457-464
Influence of scaled undeformed sections of cut on strain rate, cutting force and temperature
- 4 May 2010
- Published by Springer Nature in Production Engineering
- Vol. 4 (5) , 457-464
Influence of scaled undeformed sections of cut on strain rate, cutting force and temperature