Seng-Tjhen Lie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Seng-Tjhen Lie has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Chi King Lee
School of Engineering and Technology, University of New South Wales, Canberra, Australia
3 shared publications Zheng-Mao Yang
Associate Professor, School of Civil and Environmental Engineering, Nanyang Technological Univ., 50 Nanyang Ave., Singapore 639798
3 shared publications- Hai-Sheng Zhao
School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798
2 shared publications Sing-Ping Chiew
School of Civil and Environmental Engineering, Nanyang Technological Univ., 50 Nanyang Ave., Block N1, #1C-78, 639798 Singapore
2 shared publications- Yao Zhang
School of Architecture and Civil Engineering Xiamen University Xiamen China
2 shared publications - Z. M. Yang
Det Norske Veritas Pte. Ltd., 10 Science Park Drive, DNV Technology Centre, Singapore 118224, Singapore
2 shared publications
Latest Publications
- 19 May 2021
- Published by Springer Nature in The Visual Computer
- Vol. 38 (4) , 1209-1225
Generative design of decorative architectural parts
- 19 May 2021
- Published by Springer Nature in The Visual Computer
- Vol. 38 (4) , 1209-1225
Generative design of decorative architectural parts
- 5 June 2019
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 141 (5) , 1-10
Extracting Mode Shapes for Beams Through a Passing Auxiliary Mass
This paper shows an approach to evaluate mode shapes for beams through using a passing auxiliary mass. The coupled system of an auxiliary mass passing over a beam is time-dependent, and the corresponding instantaneous frequencies (IFs) are equivalent to the mode shapes. Hence, reconstruction of the mode shapes is easy to be achieved through estimating the IFs. A simple algorithm based on ridge detection is proposed to reconstruct the mode shapes. This method is effective if the beam is light or the lumped mass is heavy. It is convenient since it requires an accelerometer mounted on the passing auxiliary mass rather than a serious of sensors mounted on the structure itself. It is also more practical because it is usually difficult to install external exciter. A lab-scale experimental validation shows that the new technique is capable of identifying the first three mode shapes accurately.
- 5 June 2019
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 141 (5) , 1-10
Extracting Mode Shapes for Beams Through a Passing Auxiliary Mass
This paper shows an approach to evaluate mode shapes for beams through using a passing auxiliary mass. The coupled system of an auxiliary mass passing over a beam is time-dependent, and the corresponding instantaneous frequencies (IFs) are equivalent to the mode shapes. Hence, reconstruction of the mode shapes is easy to be achieved through estimating the IFs. A simple algorithm based on ridge detection is proposed to reconstruct the mode shapes. This method is effective if the beam is light or the lumped mass is heavy. It is convenient since it requires an accelerometer mounted on the passing auxiliary mass rather than a serious of sensors mounted on the structure itself. It is also more practical because it is usually difficult to install external exciter. A lab-scale experimental validation shows that the new technique is capable of identifying the first three mode shapes accurately.
- 11 January 2017
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 139 (2) , 021406
Fracture Response of Girth-Welded Pipeline With Canoe Shape Embedded Crack Subjected to Large Plastic Deformation
Long-distance offshore pipelines always suffer large plastic deformation during installation and operation. Accompanied by high internal pressure, potential flaws are found to initiate from the girth welds, and this brings a significant challenge to the structural integrity of the pipelines. The currently used procedures for fracture assessment of pipelines are usually stress based, which are unsuitable for application to cracked pipeline subjected to large plastic deformation. Therefore, the aim of this paper is to investigate the fracture assessment of pipeline subjected to large plastic deformation and identify and understand the critical parameters influencing the fracture responses under actual loading conditions. The evolution of crack tip opening displacement (CTOD) of a pipeline segment with an embedded canoe shape crack located in the middle of the girth weld is investigated under pure bending and biaxial loading through 3D elastic–plastic finite-element simulations. The effects of crack width, crack length, pipeline thickness, material hardening, and internal pressure on fracture response are discussed. Finally, a strain-based failure assessment diagram (FAD) is developed, and comparison between fracture assessment by BS7910:2013 and finite-element simulations concludes that the former produces conservative predictions for deep crack.
- 11 January 2017
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 139 (2) , 021406
Fracture Response of Girth-Welded Pipeline With Canoe Shape Embedded Crack Subjected to Large Plastic Deformation
Long-distance offshore pipelines always suffer large plastic deformation during installation and operation. Accompanied by high internal pressure, potential flaws are found to initiate from the girth welds, and this brings a significant challenge to the structural integrity of the pipelines. The currently used procedures for fracture assessment of pipelines are usually stress based, which are unsuitable for application to cracked pipeline subjected to large plastic deformation. Therefore, the aim of this paper is to investigate the fracture assessment of pipeline subjected to large plastic deformation and identify and understand the critical parameters influencing the fracture responses under actual loading conditions. The evolution of crack tip opening displacement (CTOD) of a pipeline segment with an embedded canoe shape crack located in the middle of the girth weld is investigated under pure bending and biaxial loading through 3D elastic–plastic finite-element simulations. The effects of crack width, crack length, pipeline thickness, material hardening, and internal pressure on fracture response are discussed. Finally, a strain-based failure assessment diagram (FAD) is developed, and comparison between fracture assessment by BS7910:2013 and finite-element simulations concludes that the former produces conservative predictions for deep crack.
- 26 February 2014
- Published by Taylor & Francis in The IES Journal Part A: Civil & Structural Engineering
- Vol. 7 (2) , 73-82
Detection of loose fasteners in a third rail support assembly using a wavelet analysis
The function of the third rail is to supply power in a mass rapid transit system through a semi-continuous rigid conductor placed alongside the rails of a railway track. Although it is fully segregated and fixed along the floating slab tracks (FSTs), which is used to insulate the surrounding buildings from vibration of the passing trains, the FSTs and the third rail are still prone to reverberation. Precisely because of this reason, many of the fasteners used to tighten the claw to the insulator eventually become loose, dislodging the claw holding the third rail and causing part of it to sag. This, in turn, can damage the collector shoes and causing the trains to lose power. Hence, the root of the problem is due to loose fastener in the third rail system. In this study, the dynamic response of a vehicle–rail interaction system is analysed, and the results show that the natural frequency of the interactive system decreases as a vehicle passes through a loose support. Based on this fact, a detection algorithm based on wavelet analysis is proposed. Numerical verification for different cases is produced and analysed, and the results show that it is plausible to use the proposed method in practice to detect loose fastener in a third rail support.
- 26 February 2014
- Published by Taylor & Francis in The IES Journal Part A: Civil & Structural Engineering
- Vol. 7 (2) , 73-82
Detection of loose fasteners in a third rail support assembly using a wavelet analysis
The function of the third rail is to supply power in a mass rapid transit system through a semi-continuous rigid conductor placed alongside the rails of a railway track. Although it is fully segregated and fixed along the floating slab tracks (FSTs), which is used to insulate the surrounding buildings from vibration of the passing trains, the FSTs and the third rail are still prone to reverberation. Precisely because of this reason, many of the fasteners used to tighten the claw to the insulator eventually become loose, dislodging the claw holding the third rail and causing part of it to sag. This, in turn, can damage the collector shoes and causing the trains to lose power. Hence, the root of the problem is due to loose fastener in the third rail system. In this study, the dynamic response of a vehicle–rail interaction system is analysed, and the results show that the natural frequency of the interactive system decreases as a vehicle passes through a loose support. Based on this fact, a detection algorithm based on wavelet analysis is proposed. Numerical verification for different cases is produced and analysed, and the results show that it is plausible to use the proposed method in practice to detect loose fastener in a third rail support.
- 1 October 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 137 (10) , 1132-1140
Numerical Models Validation of Cracked Square Hollow Section (SHS) Y- and K-Joints
To validate the accuracy of finite-element models of cracked square hollow section (SHS) - and -joints, two full-scale precracked specimens were tested under static incremental loads up to failure. The load-displacement curves were plotted during the tests, and a set of linear variable displacement transducers (LVDTs) were used to record the crack mouth opening displacements (CMOD) at the deepest points, whereas the crack extension was captured using the standard Alternating Current Potential Drop (ACPD) technique. The experimental results are compared with the corresponding numerical results obtained using the nonlinear finite-element method. Both sets of results show good agreement with maximum percentage differences of 7.15 and 7.96% for the plastic collapse loads and crack mouth opening displacements, respectively. Hence, the numerical model adopted previously for the cracked SHS -joints is robust and can also be used to estimate the plastic collapse load and crack driving force of any uniplanar tubular cracked - and -joints.- 1 October 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 137 (10) , 1132-1140
Numerical Models Validation of Cracked Square Hollow Section (SHS) Y- and K-Joints
To validate the accuracy of finite-element models of cracked square hollow section (SHS) - and -joints, two full-scale precracked specimens were tested under static incremental loads up to failure. The load-displacement curves were plotted during the tests, and a set of linear variable displacement transducers (LVDTs) were used to record the crack mouth opening displacements (CMOD) at the deepest points, whereas the crack extension was captured using the standard Alternating Current Potential Drop (ACPD) technique. The experimental results are compared with the corresponding numerical results obtained using the nonlinear finite-element method. Both sets of results show good agreement with maximum percentage differences of 7.15 and 7.96% for the plastic collapse loads and crack mouth opening displacements, respectively. Hence, the numerical model adopted previously for the cracked SHS -joints is robust and can also be used to estimate the plastic collapse load and crack driving force of any uniplanar tubular cracked - and -joints.- 6 December 2010
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 133 (2) , 021601
Plastic Collapse Loads of Cracked Square Hollow Section T-, Y-, and K-joints
This paper concerns on the development of numerical models for cracked square hollow sections (SHSs) T-, Y-, and K-joints. Based on these numerical models, the plastic collapse loads are calculated using nonlinear finite element method and through twice-elastic compliance criterion. It is found that the numerical plastic collapse loads are slightly conservative compared with the ones calculated using formulae proposed by BS7910 [British Standards, 2005, “Guide on Methods for Assessing the Acceptability of Flaws in Metallic Structures,” BS 7910-Amendment 1] and are in close agreement with the experimental tests data. Therefore, the proposed numerical model is robust and it can be used to calculate the plastic collapse loads of the cracked (SHS) T-, Y-, and K-joints.- 6 December 2010
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 133 (2) , 021601
Plastic Collapse Loads of Cracked Square Hollow Section T-, Y-, and K-joints
This paper concerns on the development of numerical models for cracked square hollow sections (SHSs) T-, Y-, and K-joints. Based on these numerical models, the plastic collapse loads are calculated using nonlinear finite element method and through twice-elastic compliance criterion. It is found that the numerical plastic collapse loads are slightly conservative compared with the ones calculated using formulae proposed by BS7910 [British Standards, 2005, “Guide on Methods for Assessing the Acceptability of Flaws in Metallic Structures,” BS 7910-Amendment 1] and are in close agreement with the experimental tests data. Therefore, the proposed numerical model is robust and it can be used to calculate the plastic collapse loads of the cracked (SHS) T-, Y-, and K-joints.- 30 June 2009
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 76 (9) , 1303-1319
Fracture assessment of damaged square hollow section (SHS) K-joint using BS7910:2005
- 30 June 2009
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 76 (9) , 1303-1319
Fracture assessment of damaged square hollow section (SHS) K-joint using BS7910:2005
- 1 March 2006
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 132 (3) , 378-386
Static Strength of Cracked Square Hollow Section T Joints under Axial Loads. II: Numerical
For assessing the integrity of damaged hollow section joints, the plastic collapse loads of the joints containing cracks is an important parameter. Very little published information is available in the literature concerning the residual strength of square hollow section (SHS) joints containing defects or cracks. In this paper, an accurate numerical modeling of SHS T joints with cracks is proposed, whereby the entire finite element mesh is generated automatically. To validate this numerical model, several T joint models are studied and compared with the experimental data. A good agreement is obtained on the ultimate loads. Based on this model, the plastic collapse loads under different geometrical ratios are studied, and they are compared with the results calculated from the yield line theory. It is found that the yield line theory can give a reasonable prediction of the plastic collapse loads when the brace width to chord width ratio β is less than 0.8. The failure assessment diagrams (FAD), constructed u...
- 1 March 2006
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 132 (3) , 378-386
Static Strength of Cracked Square Hollow Section T Joints under Axial Loads. II: Numerical
For assessing the integrity of damaged hollow section joints, the plastic collapse loads of the joints containing cracks is an important parameter. Very little published information is available in the literature concerning the residual strength of square hollow section (SHS) joints containing defects or cracks. In this paper, an accurate numerical modeling of SHS T joints with cracks is proposed, whereby the entire finite element mesh is generated automatically. To validate this numerical model, several T joint models are studied and compared with the experimental data. A good agreement is obtained on the ultimate loads. Based on this model, the plastic collapse loads under different geometrical ratios are studied, and they are compared with the results calculated from the yield line theory. It is found that the yield line theory can give a reasonable prediction of the plastic collapse loads when the brace width to chord width ratio β is less than 0.8. The failure assessment diagrams (FAD), constructed u...
- 1 March 2006
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 132 (3) , 368-377
Static Strength of Cracked Square Hollow Section T Joints under Axial Loads. I: Experimental
A series of static strength tests were performed on full-scale precracked square-to-square hollow section welded T joints. These joints were subjected under brace end axial load until failure using a special purpose designed test rig. An alternating current potential drop technique was employed to monitor the crack propagation during the tests. In addition, three sets of linear variable displacement transducers were used to record the crack mouth opening displacements. The tests were performed at room temperature; therefore, the material is on the upper shelf of the ductile-brittle transition curve where failure occurs in a ductile manner. In all these tests, a stable ductile tearing was observed with a small tearing region. Based on the yield line theory, the plastic collapse load is estimated, and then applied to the failure assessment diagram (FAD) of BS7910. The results show that BS7910 Level 2A FAD provides an adequate procedure for the assessment of cracked square-to-square hollow section T joints.
- 1 March 2006
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 132 (3) , 368-377
Static Strength of Cracked Square Hollow Section T Joints under Axial Loads. I: Experimental
A series of static strength tests were performed on full-scale precracked square-to-square hollow section welded T joints. These joints were subjected under brace end axial load until failure using a special purpose designed test rig. An alternating current potential drop technique was employed to monitor the crack propagation during the tests. In addition, three sets of linear variable displacement transducers were used to record the crack mouth opening displacements. The tests were performed at room temperature; therefore, the material is on the upper shelf of the ductile-brittle transition curve where failure occurs in a ductile manner. In all these tests, a stable ductile tearing was observed with a small tearing region. Based on the yield line theory, the plastic collapse load is estimated, and then applied to the failure assessment diagram (FAD) of BS7910. The results show that BS7910 Level 2A FAD provides an adequate procedure for the assessment of cracked square-to-square hollow section T joints.
- 1 February 2006
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 9 (1) , 129-139
Stress Intensity Factor Solutions for Semi-Elliptical Weld-Toe Cracks in Tubular K-Joints
Stress intensity factors (SIFs) are generally used to predict the remaining life of cracked tubular K-joints used in the offshore structures. The accuracy of SIFs depends very much on accurate modelling of the surface crack. In this paper, a new mesh generation method is proposed for any cracked tubular K-joint where five types of elements are adopted in modelling the surface crack so as to avoid high elements aspect ratio around the crack front. The mesh of any K-joint is obtained by merging the mesh of several distinct regions, and each region is generated separately according to different requirements. To check the accuracy of the computed SIFs, two large scale K-joint specimens were tested to failure under fatigue loading conditions. The alternating current potential drop (ACPD) technique is used to monitor the rate of crack propagation of the surface crack located at the crown position. The experimental test results are then used to validate the numerical results. Generally, they agree well and the relative errors are acceptable.
- 1 February 2006
- Published by SAGE Publications in Advances in Structural Engineering
- Vol. 9 (1) , 129-139
Stress Intensity Factor Solutions for Semi-Elliptical Weld-Toe Cracks in Tubular K-Joints
Stress intensity factors (SIFs) are generally used to predict the remaining life of cracked tubular K-joints used in the offshore structures. The accuracy of SIFs depends very much on accurate modelling of the surface crack. In this paper, a new mesh generation method is proposed for any cracked tubular K-joint where five types of elements are adopted in modelling the surface crack so as to avoid high elements aspect ratio around the crack front. The mesh of any K-joint is obtained by merging the mesh of several distinct regions, and each region is generated separately according to different requirements. To check the accuracy of the computed SIFs, two large scale K-joint specimens were tested to failure under fatigue loading conditions. The alternating current potential drop (ACPD) technique is used to monitor the rate of crack propagation of the surface crack located at the crown position. The experimental test results are then used to validate the numerical results. Generally, they agree well and the relative errors are acceptable.