Yongjia Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yongjia Li has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Weifeng Sun
Southeast University
13 shared publications - Long Zhang
Southeast University
7 shared publications - Zhongyuan Fang
Southeast University
7 shared publications Dejin Wang
CSMC Technologies Corporation, Wuxi, China
6 shared publications- Jianlin Xia
School of Integrated Circuits, Southeast University, Nanjing, China
6 shared publications Encheng Zhu
China Resources Microelectronics Ltd., Wuxi, China
5 shared publications
Latest Publications
- Open Access
- 14 September 2026
- Published by MDPI AG in Electronics
- Vol. 15 (18) , 4155
An Incremental Zoom ADC Readout IC and FPGA-Based Digital Calibration System for High-Precision Capacitive Pressure Sensors
This work presents an incremental zoom analog-to-digital converter (ADC) readout integrated circuit (IC) and field-programmable gate array (FPGA)-based digital calibration system for high-precision capacitive micro electro-mechanical system (MEMS) pressure sensors, aimed at enhancing pressure readout resolution, pressure measurement accuracy, and long-term output stability. In the readout IC, the zoom ADC employs coarse-fine quantization, achieving high readout accuracy while relaxing requirements on integrator output swing and front-end linearity. On the digital side, a sparrow-search-algorithm-optimized Gaussian process regression (SSA-GPR) model constructs a nonlinear pressure–temperature mapping with limited calibration samples, while a segmented aging-compensation scheme based on dual-channel periodic self-test dynamically corrects aging-induced offset and sensitivity drifts. Together, these three techniques form a complete signal-conditioning chain addressing weak capacitance variation readout, pressure–temperature coupling, and long-term drift. Measured results show 0.11 PaRMS output root mean square (RMS) noise under a 205.2 ms conversion time, 37.44 Pa mean absolute error over −40 °C to 85 °C and 30 kPa to 120 kPa, and ±30 Pa residual error after 85 °C/1000 h aging, confirming the effectiveness of the proposed readout IC and digital calibration system.
- 14 September 2026
- Published by MDPI AG in Electronics
- Vol. 15 (18) , 4155
Open AccessAn Incremental Zoom ADC Readout IC and FPGA-Based Digital Calibration System for High-Precision Capacitive Pressure Sensors
This work presents an incremental zoom analog-to-digital converter (ADC) readout integrated circuit (IC) and field-programmable gate array (FPGA)-based digital calibration system for high-precision capacitive micro electro-mechanical system (MEMS) pressure sensors, aimed at enhancing pressure readout resolution, pressure measurement accuracy, and long-term output stability. In the readout IC, the zoom ADC employs coarse-fine quantization, achieving high readout accuracy while relaxing requirements on integrator output swing and front-end linearity. On the digital side, a sparrow-search-algorithm-optimized Gaussian process regression (SSA-GPR) model constructs a nonlinear pressure–temperature mapping with limited calibration samples, while a segmented aging-compensation scheme based on dual-channel periodic self-test dynamically corrects aging-induced offset and sensitivity drifts. Together, these three techniques form a complete signal-conditioning chain addressing weak capacitance variation readout, pressure–temperature coupling, and long-term drift. Measured results show 0.11 PaRMS output root mean square (RMS) noise under a 205.2 ms conversion time, 37.44 Pa mean absolute error over −40 °C to 85 °C and 30 kPa to 120 kPa, and ±30 Pa residual error after 85 °C/1000 h aging, confirming the effectiveness of the proposed readout IC and digital calibration system.
- 19 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-13
A 15-MHz, 2.7-mm 2 Notch-Free Hybrid Magnetic Current Sensor With Feedforward Ripple Cancellation and ±0.8% Local Gain Non-Uniformity
This article proposes a hybrid magnetic current sensor achieving a 15-MHz bandwidth within a compact 2.7-mm2 area. To mitigate the pole–zero mismatch inherent in the two-stage integrator topology, a dual-output Gm-C integrator with subtractor-based compensation is proposed, achieving a ±0.8% local gain non-uniformity. A wideband feedforward ripple suppression scheme cancels chopping ripple without bandwidth degradation, achieving 25-dB suppression while avoiding in-band notches common in ripple reduction loop (RRL) schemes. In addition, two active capacitor-boosting techniques enhance the effective capacitance in the DC servo loop (DCSL) and the differential difference amplifier (DDA), realizing significant passive area savings. While the Hall sensitivity drift is compensated by bias current with a positive temperature coefficient (PTC), a negative-temperature-coefficient (NTC) ground technique is proposed to stabilize the Hall-plate common-mode (CM) output. Compared with the state of the art, the proposed sensor achieves $3\times $ higher bandwidth, $1.5\times $ improved gain flatness, and 30% smaller chip area.
- 19 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-13
A 15-MHz, 2.7-mm 2 Notch-Free Hybrid Magnetic Current Sensor With Feedforward Ripple Cancellation and ±0.8% Local Gain Non-Uniformity
This article proposes a hybrid magnetic current sensor achieving a 15-MHz bandwidth within a compact 2.7-mm2 area. To mitigate the pole–zero mismatch inherent in the two-stage integrator topology, a dual-output Gm-C integrator with subtractor-based compensation is proposed, achieving a ±0.8% local gain non-uniformity. A wideband feedforward ripple suppression scheme cancels chopping ripple without bandwidth degradation, achieving 25-dB suppression while avoiding in-band notches common in ripple reduction loop (RRL) schemes. In addition, two active capacitor-boosting techniques enhance the effective capacitance in the DC servo loop (DCSL) and the differential difference amplifier (DDA), realizing significant passive area savings. While the Hall sensitivity drift is compensated by bias current with a positive temperature coefficient (PTC), a negative-temperature-coefficient (NTC) ground technique is proposed to stabilize the Hall-plate common-mode (CM) output. Compared with the state of the art, the proposed sensor achieves $3\times $ higher bandwidth, $1.5\times $ improved gain flatness, and 30% smaller chip area.
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (1) , 860-870
A Pipelined Cycle-Variable RBFNN Using Low-Latency Two-Step Bypass Scale-Free CORDIC for TMR Temperature Compensation
This paper presents a low-latency, two-step bypass hyperbolic scale-free Coordinate Rotation Digital Computer (CORDIC) algorithm, which is applied to the Radial Basis Function Neural Network (RBFNN)-based temperature compensation model in tunneling magnetoresistance (TMR) sensor current sensing. The proposed method leverages an enhanced Taylor series approximation in conjunction with binary digit representation to achieve an efficient coordinate iteration. This method inherently eliminates power-of-three terms in the two-step iteration. Notably, there are no complex thresholds in microrotations. To further minimize latency, the last five iterations of the original nine can be consolidated into a single linear iteration. Verified on the Field-Programmable Gate Array (FPGA), over a temperature range of -40 to 120°C, there is a significant reduction in the temperature sensitivity coefficient, from 426 ppm/°C to 39.38 ppm/°C. And the zero temperature coefficient decreases from 33.30 ppm/°C to 13.13 ppm/°C. By dynamically adjusting the number of iterations, the pipelined cycle-variable RBFNN achieves the lowest latency in the circuit implementation. Among existing temperature compensation methods for TMR current sensors, the proposed approach achieves the highest measurement accuracy, reaching as low as 0.19%.
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (1) , 860-870
A Pipelined Cycle-Variable RBFNN Using Low-Latency Two-Step Bypass Scale-Free CORDIC for TMR Temperature Compensation
This paper presents a low-latency, two-step bypass hyperbolic scale-free Coordinate Rotation Digital Computer (CORDIC) algorithm, which is applied to the Radial Basis Function Neural Network (RBFNN)-based temperature compensation model in tunneling magnetoresistance (TMR) sensor current sensing. The proposed method leverages an enhanced Taylor series approximation in conjunction with binary digit representation to achieve an efficient coordinate iteration. This method inherently eliminates power-of-three terms in the two-step iteration. Notably, there are no complex thresholds in microrotations. To further minimize latency, the last five iterations of the original nine can be consolidated into a single linear iteration. Verified on the Field-Programmable Gate Array (FPGA), over a temperature range of -40 to 120°C, there is a significant reduction in the temperature sensitivity coefficient, from 426 ppm/°C to 39.38 ppm/°C. And the zero temperature coefficient decreases from 33.30 ppm/°C to 13.13 ppm/°C. By dynamically adjusting the number of iterations, the pipelined cycle-variable RBFNN achieves the lowest latency in the circuit implementation. Among existing temperature compensation methods for TMR current sensors, the proposed approach achieves the highest measurement accuracy, reaching as low as 0.19%.
- 16 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (23) , 42859-42870
A 10-MHz, 2.3-mm² Hybrid Magnetic Current Sensor Using Gain–Bandwidth Decoupled DDA and Passive-Aided Bandwidth Extension
This paper presents a wide bandwidth hybrid current sensor that incorporates a wideband instrumentation amplifier (IA) in the low-frequency (LF) path and a high gain-bandwidth product (GBW) integrator in the high-frequency (HF) path. The ping-pong switched-capacitor demodulator (PPSCD) in the LF path effectively suppresses ripple while introducing negligible gain non-uniformity. A two-stage integrator topology is adopted in the HF path to extend bandwidth and reduce noise compared to its single-stage counterpart. The implementation of a DC servo loop with an attenuator around the HF integrator minimizes offset with reduced area overhead. Additional area savings are achieved by employing a gain-bandwidth decoupled differential difference amplifier (DDA), which combines signals from the LF Hall path and HF coil path, and incorporates a peripheral passive bypass path for bandwidth enhancement. The proposed design achieves a 10 MHz bandwidth in a compact 2.3 mm² area, representing a 2× bandwidth improvement and 40% area reduction compared to the state-of-the-art.
- 16 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (23) , 42859-42870
A 10-MHz, 2.3-mm² Hybrid Magnetic Current Sensor Using Gain–Bandwidth Decoupled DDA and Passive-Aided Bandwidth Extension
This paper presents a wide bandwidth hybrid current sensor that incorporates a wideband instrumentation amplifier (IA) in the low-frequency (LF) path and a high gain-bandwidth product (GBW) integrator in the high-frequency (HF) path. The ping-pong switched-capacitor demodulator (PPSCD) in the LF path effectively suppresses ripple while introducing negligible gain non-uniformity. A two-stage integrator topology is adopted in the HF path to extend bandwidth and reduce noise compared to its single-stage counterpart. The implementation of a DC servo loop with an attenuator around the HF integrator minimizes offset with reduced area overhead. Additional area savings are achieved by employing a gain-bandwidth decoupled differential difference amplifier (DDA), which combines signals from the LF Hall path and HF coil path, and incorporates a peripheral passive bypass path for bandwidth enhancement. The proposed design achieves a 10 MHz bandwidth in a compact 2.3 mm² area, representing a 2× bandwidth improvement and 40% area reduction compared to the state-of-the-art.
- 29 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. PP, 1
An 8.5 MHz 42 ppm/∘ C Relaxation Oscillator With Charge-Pump Delay Cancellation and Digital Chopping Demodulation
This paper presents an RC oscillator featuring a mixed-signal compensation loop that simultaneously mitigates comparator offset, loop delay, switch on-resistance, and temperature dependency. The oscillator employs an auxiliary comparator, a charge pump and a differential difference amplifier (DDA)-based main comparator to suppress ramping voltage overshoots caused by device and loop imperfections. Moreover, the auxiliary comparator employs chopper and digital demodulation techniques to suppress its own offset, further enhancing the accuracy of the calibration loop. By generating both ramping and reference voltages, the proportional-to-absolute-temperature (PTAT) core ensures that the temperature coefficient (TC) of the oscillation frequency primarily depends on passive RC components. Fabricated in a 0.18 μm BCD process, the design achieves an average frequency TC of 42 ppm/∘C from -20 ∘C to 125 ∘C across 10 samples. Benefiting from the proposed architecture, the oscillator operates at 8.45 MHz with a fast startup calibration time of 50 μs.
- 29 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. PP, 1
An 8.5 MHz 42 ppm/∘ C Relaxation Oscillator With Charge-Pump Delay Cancellation and Digital Chopping Demodulation
This paper presents an RC oscillator featuring a mixed-signal compensation loop that simultaneously mitigates comparator offset, loop delay, switch on-resistance, and temperature dependency. The oscillator employs an auxiliary comparator, a charge pump and a differential difference amplifier (DDA)-based main comparator to suppress ramping voltage overshoots caused by device and loop imperfections. Moreover, the auxiliary comparator employs chopper and digital demodulation techniques to suppress its own offset, further enhancing the accuracy of the calibration loop. By generating both ramping and reference voltages, the proportional-to-absolute-temperature (PTAT) core ensures that the temperature coefficient (TC) of the oscillation frequency primarily depends on passive RC components. Fabricated in a 0.18 μm BCD process, the design achieves an average frequency TC of 42 ppm/∘C from -20 ∘C to 125 ∘C across 10 samples. Benefiting from the proposed architecture, the oscillator operates at 8.45 MHz with a fast startup calibration time of 50 μs.
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (1) , 39-50
A 2 MHz Bandwidth Area-Efficient Multipath Hall Sensor With a Residual Ripple of 4.1 μT
This paper presents a multipath wide-bandwidth magnetic current sensor based on Hall effect. To simultaneously achieve wide bandwidth, minimal ripple and small area, the system incorporates a non-spun filter-free main path with offset elimination through a continuous-time compact auxiliary path. The auxiliary path cancels the main path offset via feedforward, alleviating the need for area-consuming blocking capacitor or DC servo loop. Therefore, the chip occupies only 1.52 mm2. To suppress ripple in the auxiliary path induced by spinning current, a ping-pong switch-capacitor (PPSC) filter is proposed which mitigates ripple by sampling and averaging in the forward path, with the system achieving a residual ripple of $4.1~{\mu }$ T. Compared with the state-of-the-art Hall sensor, it achieves $5{\times }$ bandwidth improvement, $2{\times }$ ripple reduction while occupying $5{\times }$ less area.
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (1) , 39-50
A 2 MHz Bandwidth Area-Efficient Multipath Hall Sensor With a Residual Ripple of 4.1 μT
This paper presents a multipath wide-bandwidth magnetic current sensor based on Hall effect. To simultaneously achieve wide bandwidth, minimal ripple and small area, the system incorporates a non-spun filter-free main path with offset elimination through a continuous-time compact auxiliary path. The auxiliary path cancels the main path offset via feedforward, alleviating the need for area-consuming blocking capacitor or DC servo loop. Therefore, the chip occupies only 1.52 mm2. To suppress ripple in the auxiliary path induced by spinning current, a ping-pong switch-capacitor (PPSC) filter is proposed which mitigates ripple by sampling and averaging in the forward path, with the system achieving a residual ripple of $4.1~{\mu }$ T. Compared with the state-of-the-art Hall sensor, it achieves $5{\times }$ bandwidth improvement, $2{\times }$ ripple reduction while occupying $5{\times }$ less area.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (4) , 2020-2024
Multiwindow Implantation Method in Vertical Hall Devices for High Sensitivity
A novel vertical Hall device (VHD), featuring a waved boundary magnetic-sensitive well, is proposed for the first time in this article. By applying multiwindow implantation (MWI) method in 0.15-μm bipolar–CMOS–DMOS (BCD) platform, nonuniform doping profile in lateral and vertical directions is realized and the path of bias current is changed subsequently. The current path with long route and low resistance in the proposed VHD increases the ratio of longitudinal current and a current related sensitivity (SI) of 178 V/AT is achieved, which is 49.6% improved compared with the standard VHD. The proposed VHD provides a new solution for the design of high-sensitivity Hall device.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (4) , 2020-2024
Multiwindow Implantation Method in Vertical Hall Devices for High Sensitivity
A novel vertical Hall device (VHD), featuring a waved boundary magnetic-sensitive well, is proposed for the first time in this article. By applying multiwindow implantation (MWI) method in 0.15-μm bipolar–CMOS–DMOS (BCD) platform, nonuniform doping profile in lateral and vertical directions is realized and the path of bias current is changed subsequently. The current path with long route and low resistance in the proposed VHD increases the ratio of longitudinal current and a current related sensitivity (SI) of 178 V/AT is achieved, which is 49.6% improved compared with the standard VHD. The proposed VHD provides a new solution for the design of high-sensitivity Hall device.
- Open Access
- 25 February 2025
- Published by MDPI AG in Electronics
- Vol. 14 (5) , 904
Design and Control of the Resonant Auxiliary Circuit for Voltage Regulator Module (VRM) with Fast Load Step Transient
This paper proposes a transient energy auxiliary supply circuit architecture based on resonant switched-capacitor principles, aimed at optimizing the system’s transient response to meet the growing power supply demands. This paper first introduces the relevant principles of resonant switched-capacitor converters. Based on this, a transient energy path topology based on resonant principles is designed to achieve bidirectional, fast, and low electromagnetic interference energy transmission. Corresponding system coordination control strategies and high-precision switch control based on delay lines are proposed for the designed circuit topology. A circuit model is built in SIMPLIS (V8.20a) software for system simulation, and a prototype is built based on FPGA to verify circuit functionality and performance. Experimental results demonstrate that the resonant energy auxiliary circuit can operate in conjunction with a six-phase Buck circuit prototype. Under test conditions of a 500 kHz operating frequency, 6.5 V input voltage, and 0.75 V output voltage, the overshoot voltage is reduced by more than 17% across the entire operating range. When the load steps from 200 A to 20 A, the overshoot voltage is reduced to only 85 mV, a decrease of 27.97%, while the recovery time is 28.8 µs, a reduction of 37.66%. These results confirm that the auxiliary circuit can significantly improve the system’s transient response under large load steps, meeting the design requirements.
- 25 February 2025
- Published by MDPI AG in Electronics
- Vol. 14 (5) , 904
Open AccessDesign and Control of the Resonant Auxiliary Circuit for Voltage Regulator Module (VRM) with Fast Load Step Transient
This paper proposes a transient energy auxiliary supply circuit architecture based on resonant switched-capacitor principles, aimed at optimizing the system’s transient response to meet the growing power supply demands. This paper first introduces the relevant principles of resonant switched-capacitor converters. Based on this, a transient energy path topology based on resonant principles is designed to achieve bidirectional, fast, and low electromagnetic interference energy transmission. Corresponding system coordination control strategies and high-precision switch control based on delay lines are proposed for the designed circuit topology. A circuit model is built in SIMPLIS (V8.20a) software for system simulation, and a prototype is built based on FPGA to verify circuit functionality and performance. Experimental results demonstrate that the resonant energy auxiliary circuit can operate in conjunction with a six-phase Buck circuit prototype. Under test conditions of a 500 kHz operating frequency, 6.5 V input voltage, and 0.75 V output voltage, the overshoot voltage is reduced by more than 17% across the entire operating range. When the load steps from 200 A to 20 A, the overshoot voltage is reduced to only 85 mV, a decrease of 27.97%, while the recovery time is 28.8 µs, a reduction of 37.66%. These results confirm that the auxiliary circuit can significantly improve the system’s transient response under large load steps, meeting the design requirements.
- 6 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (9) , 4550-4559
A 870 ppm/V 53 ppm/ ° C 7 MHz Non-Trimmed RC Relaxation Oscillator Using Mixed-Signal Compensation Loop From - 40 ∘C to 165 ∘C
In this paper, an RC relaxation oscillator exhibiting robust performance over an extended temperature and supply range is proposed. By incorporating a digitally-assisted calibration loop, the design eliminates the errors from switch on-resistance, comparator offset and propagation delay. Fabricated using a 180 nm bipolar-CMOS-DMOS (BCD) process technology, the oscillator operates at a frequency of 7MHz with the supply sensitivity of 870 ppm/V across a voltage range of 1.7 to 4.2 V. The evaluation of 40 untrimmed samples achieved an average temperature coefficient (TC) of 52 ppm/°C from −40°C to $165~^{\circ }$ C, with the worst observed TC being 81 ppm/°C. The aging test results indicate small deviations of 0.3% and 11% in the oscillation frequency and its TC, respectively. Furthermore, the direct power injection test confirms its reliability and robustness with a maximum error of oscillation frequency of 6.4%.
- 6 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (9) , 4550-4559
A 870 ppm/V 53 ppm/ ° C 7 MHz Non-Trimmed RC Relaxation Oscillator Using Mixed-Signal Compensation Loop From - 40 ∘C to 165 ∘C
In this paper, an RC relaxation oscillator exhibiting robust performance over an extended temperature and supply range is proposed. By incorporating a digitally-assisted calibration loop, the design eliminates the errors from switch on-resistance, comparator offset and propagation delay. Fabricated using a 180 nm bipolar-CMOS-DMOS (BCD) process technology, the oscillator operates at a frequency of 7MHz with the supply sensitivity of 870 ppm/V across a voltage range of 1.7 to 4.2 V. The evaluation of 40 untrimmed samples achieved an average temperature coefficient (TC) of 52 ppm/°C from −40°C to $165~^{\circ }$ C, with the worst observed TC being 81 ppm/°C. The aging test results indicate small deviations of 0.3% and 11% in the oscillation frequency and its TC, respectively. Furthermore, the direct power injection test confirms its reliability and robustness with a maximum error of oscillation frequency of 6.4%.