Jianlin Xia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jianlin Xia has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Weifeng Sun
Southeast University
7 shared publications Encheng Zhu
6 shared publications- Yongjia Li
School of Integrated Circuits, Southeast University, Nanjing, China
6 shared publications - Zhongyuan Fang
Southeast University
5 shared publications Dejin Wang
4 shared publications- Feng Cheng
School of Integrated Circuits, Southeast University, Nanjing, China
4 shared publications
Latest Publications
- 21 October 2026
- Published by Elsevier in Microelectronics Journal
- Vol. 179
A 4MHz, 9.7ppm/°C, ±0.36% inaccuracy RC oscillator using geometric-space-based trimming method from −40 °C to 150 °C
- 21 October 2026
- Published by Elsevier in Microelectronics Journal
- Vol. 179
A 4MHz, 9.7ppm/°C, ±0.36% inaccuracy RC oscillator using geometric-space-based trimming method from −40 °C to 150 °C
- 19 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-13
A 15-MHz, 2.7-mm 2 Notch-Free Hybrid Magnetic Current Sensor With Feedforward Ripple Cancellation and ±0.8% Local Gain Non-Uniformity
This article proposes a hybrid magnetic current sensor achieving a 15-MHz bandwidth within a compact 2.7-mm2 area. To mitigate the pole–zero mismatch inherent in the two-stage integrator topology, a dual-output Gm-C integrator with subtractor-based compensation is proposed, achieving a ±0.8% local gain non-uniformity. A wideband feedforward ripple suppression scheme cancels chopping ripple without bandwidth degradation, achieving 25-dB suppression while avoiding in-band notches common in ripple reduction loop (RRL) schemes. In addition, two active capacitor-boosting techniques enhance the effective capacitance in the DC servo loop (DCSL) and the differential difference amplifier (DDA), realizing significant passive area savings. While the Hall sensitivity drift is compensated by bias current with a positive temperature coefficient (PTC), a negative-temperature-coefficient (NTC) ground technique is proposed to stabilize the Hall-plate common-mode (CM) output. Compared with the state of the art, the proposed sensor achieves $3\times $ higher bandwidth, $1.5\times $ improved gain flatness, and 30% smaller chip area.
- 19 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-13
A 15-MHz, 2.7-mm 2 Notch-Free Hybrid Magnetic Current Sensor With Feedforward Ripple Cancellation and ±0.8% Local Gain Non-Uniformity
This article proposes a hybrid magnetic current sensor achieving a 15-MHz bandwidth within a compact 2.7-mm2 area. To mitigate the pole–zero mismatch inherent in the two-stage integrator topology, a dual-output Gm-C integrator with subtractor-based compensation is proposed, achieving a ±0.8% local gain non-uniformity. A wideband feedforward ripple suppression scheme cancels chopping ripple without bandwidth degradation, achieving 25-dB suppression while avoiding in-band notches common in ripple reduction loop (RRL) schemes. In addition, two active capacitor-boosting techniques enhance the effective capacitance in the DC servo loop (DCSL) and the differential difference amplifier (DDA), realizing significant passive area savings. While the Hall sensitivity drift is compensated by bias current with a positive temperature coefficient (PTC), a negative-temperature-coefficient (NTC) ground technique is proposed to stabilize the Hall-plate common-mode (CM) output. Compared with the state of the art, the proposed sensor achieves $3\times $ higher bandwidth, $1.5\times $ improved gain flatness, and 30% smaller chip area.
- 16 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (23) , 42859-42870
A 10-MHz, 2.3-mm² Hybrid Magnetic Current Sensor Using Gain–Bandwidth Decoupled DDA and Passive-Aided Bandwidth Extension
This paper presents a wide bandwidth hybrid current sensor that incorporates a wideband instrumentation amplifier (IA) in the low-frequency (LF) path and a high gain-bandwidth product (GBW) integrator in the high-frequency (HF) path. The ping-pong switched-capacitor demodulator (PPSCD) in the LF path effectively suppresses ripple while introducing negligible gain non-uniformity. A two-stage integrator topology is adopted in the HF path to extend bandwidth and reduce noise compared to its single-stage counterpart. The implementation of a DC servo loop with an attenuator around the HF integrator minimizes offset with reduced area overhead. Additional area savings are achieved by employing a gain-bandwidth decoupled differential difference amplifier (DDA), which combines signals from the LF Hall path and HF coil path, and incorporates a peripheral passive bypass path for bandwidth enhancement. The proposed design achieves a 10 MHz bandwidth in a compact 2.3 mm² area, representing a 2× bandwidth improvement and 40% area reduction compared to the state-of-the-art.
- 16 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (23) , 42859-42870
A 10-MHz, 2.3-mm² Hybrid Magnetic Current Sensor Using Gain–Bandwidth Decoupled DDA and Passive-Aided Bandwidth Extension
This paper presents a wide bandwidth hybrid current sensor that incorporates a wideband instrumentation amplifier (IA) in the low-frequency (LF) path and a high gain-bandwidth product (GBW) integrator in the high-frequency (HF) path. The ping-pong switched-capacitor demodulator (PPSCD) in the LF path effectively suppresses ripple while introducing negligible gain non-uniformity. A two-stage integrator topology is adopted in the HF path to extend bandwidth and reduce noise compared to its single-stage counterpart. The implementation of a DC servo loop with an attenuator around the HF integrator minimizes offset with reduced area overhead. Additional area savings are achieved by employing a gain-bandwidth decoupled differential difference amplifier (DDA), which combines signals from the LF Hall path and HF coil path, and incorporates a peripheral passive bypass path for bandwidth enhancement. The proposed design achieves a 10 MHz bandwidth in a compact 2.3 mm² area, representing a 2× bandwidth improvement and 40% area reduction compared to the state-of-the-art.
- 29 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. PP, 1
An 8.5 MHz 42 ppm/∘ C Relaxation Oscillator With Charge-Pump Delay Cancellation and Digital Chopping Demodulation
This paper presents an RC oscillator featuring a mixed-signal compensation loop that simultaneously mitigates comparator offset, loop delay, switch on-resistance, and temperature dependency. The oscillator employs an auxiliary comparator, a charge pump and a differential difference amplifier (DDA)-based main comparator to suppress ramping voltage overshoots caused by device and loop imperfections. Moreover, the auxiliary comparator employs chopper and digital demodulation techniques to suppress its own offset, further enhancing the accuracy of the calibration loop. By generating both ramping and reference voltages, the proportional-to-absolute-temperature (PTAT) core ensures that the temperature coefficient (TC) of the oscillation frequency primarily depends on passive RC components. Fabricated in a 0.18 μm BCD process, the design achieves an average frequency TC of 42 ppm/∘C from -20 ∘C to 125 ∘C across 10 samples. Benefiting from the proposed architecture, the oscillator operates at 8.45 MHz with a fast startup calibration time of 50 μs.
- 29 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. PP, 1
An 8.5 MHz 42 ppm/∘ C Relaxation Oscillator With Charge-Pump Delay Cancellation and Digital Chopping Demodulation
This paper presents an RC oscillator featuring a mixed-signal compensation loop that simultaneously mitigates comparator offset, loop delay, switch on-resistance, and temperature dependency. The oscillator employs an auxiliary comparator, a charge pump and a differential difference amplifier (DDA)-based main comparator to suppress ramping voltage overshoots caused by device and loop imperfections. Moreover, the auxiliary comparator employs chopper and digital demodulation techniques to suppress its own offset, further enhancing the accuracy of the calibration loop. By generating both ramping and reference voltages, the proportional-to-absolute-temperature (PTAT) core ensures that the temperature coefficient (TC) of the oscillation frequency primarily depends on passive RC components. Fabricated in a 0.18 μm BCD process, the design achieves an average frequency TC of 42 ppm/∘C from -20 ∘C to 125 ∘C across 10 samples. Benefiting from the proposed architecture, the oscillator operates at 8.45 MHz with a fast startup calibration time of 50 μs.
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (1) , 39-50
A 2 MHz Bandwidth Area-Efficient Multipath Hall Sensor With a Residual Ripple of 4.1 μT
This paper presents a multipath wide-bandwidth magnetic current sensor based on Hall effect. To simultaneously achieve wide bandwidth, minimal ripple and small area, the system incorporates a non-spun filter-free main path with offset elimination through a continuous-time compact auxiliary path. The auxiliary path cancels the main path offset via feedforward, alleviating the need for area-consuming blocking capacitor or DC servo loop. Therefore, the chip occupies only 1.52 mm2. To suppress ripple in the auxiliary path induced by spinning current, a ping-pong switch-capacitor (PPSC) filter is proposed which mitigates ripple by sampling and averaging in the forward path, with the system achieving a residual ripple of $4.1~{\mu }$ T. Compared with the state-of-the-art Hall sensor, it achieves $5{\times }$ bandwidth improvement, $2{\times }$ ripple reduction while occupying $5{\times }$ less area.
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (1) , 39-50
A 2 MHz Bandwidth Area-Efficient Multipath Hall Sensor With a Residual Ripple of 4.1 μT
This paper presents a multipath wide-bandwidth magnetic current sensor based on Hall effect. To simultaneously achieve wide bandwidth, minimal ripple and small area, the system incorporates a non-spun filter-free main path with offset elimination through a continuous-time compact auxiliary path. The auxiliary path cancels the main path offset via feedforward, alleviating the need for area-consuming blocking capacitor or DC servo loop. Therefore, the chip occupies only 1.52 mm2. To suppress ripple in the auxiliary path induced by spinning current, a ping-pong switch-capacitor (PPSC) filter is proposed which mitigates ripple by sampling and averaging in the forward path, with the system achieving a residual ripple of $4.1~{\mu }$ T. Compared with the state-of-the-art Hall sensor, it achieves $5{\times }$ bandwidth improvement, $2{\times }$ ripple reduction while occupying $5{\times }$ less area.
- 6 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (9) , 4550-4559
A 870 ppm/V 53 ppm/ ° C 7 MHz Non-Trimmed RC Relaxation Oscillator Using Mixed-Signal Compensation Loop From - 40 ∘C to 165 ∘C
In this paper, an RC relaxation oscillator exhibiting robust performance over an extended temperature and supply range is proposed. By incorporating a digitally-assisted calibration loop, the design eliminates the errors from switch on-resistance, comparator offset and propagation delay. Fabricated using a 180 nm bipolar-CMOS-DMOS (BCD) process technology, the oscillator operates at a frequency of 7MHz with the supply sensitivity of 870 ppm/V across a voltage range of 1.7 to 4.2 V. The evaluation of 40 untrimmed samples achieved an average temperature coefficient (TC) of 52 ppm/°C from −40°C to $165~^{\circ }$ C, with the worst observed TC being 81 ppm/°C. The aging test results indicate small deviations of 0.3% and 11% in the oscillation frequency and its TC, respectively. Furthermore, the direct power injection test confirms its reliability and robustness with a maximum error of oscillation frequency of 6.4%.
- 6 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (9) , 4550-4559
A 870 ppm/V 53 ppm/ ° C 7 MHz Non-Trimmed RC Relaxation Oscillator Using Mixed-Signal Compensation Loop From - 40 ∘C to 165 ∘C
In this paper, an RC relaxation oscillator exhibiting robust performance over an extended temperature and supply range is proposed. By incorporating a digitally-assisted calibration loop, the design eliminates the errors from switch on-resistance, comparator offset and propagation delay. Fabricated using a 180 nm bipolar-CMOS-DMOS (BCD) process technology, the oscillator operates at a frequency of 7MHz with the supply sensitivity of 870 ppm/V across a voltage range of 1.7 to 4.2 V. The evaluation of 40 untrimmed samples achieved an average temperature coefficient (TC) of 52 ppm/°C from −40°C to $165~^{\circ }$ C, with the worst observed TC being 81 ppm/°C. The aging test results indicate small deviations of 0.3% and 11% in the oscillation frequency and its TC, respectively. Furthermore, the direct power injection test confirms its reliability and robustness with a maximum error of oscillation frequency of 6.4%.