Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mona Mostafa Hella has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Top-Illuminated Annular Ge-on-Si APD in 45-nm Lateral SOI Process With High Gain–Bandwidth Product at 4 V Reverse Bias

    by Nabil Shehtab Dhrubo, John W. Rollinson, Robert F. Karlicek, Mona M. Hella

    A top-illuminated Ge-on-Si avalanche photodiode is designed and fabricated in GlobalFoundries’ 45-nm SOI platform (Si Photonic). The device utilizes an annular-shaped germanium layer as the absorption region, enclosed by cathode contacts to ensure avalanche multiplication of photocarriers and flow of photocurrent from all directions to the central anode. The proposed device structure modification results in an increased gain within a small silicon area. The device utilizes a germanium width of $0.8~\mu $ m to reduce the carrier transit time and achieve high optoelectronic bandwidth. Testing is performed using 940- and 1550-nm wavelength continuous wave lasers. At a reverse bias of 4 V, the device shows a peak gain of 3.5 and 8.6 at 940- and 1550-nm wavelength, respectively. At the same bias, a -3-dB optoelectronic bandwidth of around 13.4 GHz is observed for 1550-nm wavelength. This results in a gain-bandwidth product (GBP) of ~115 GHz at 1550-nm wavelength for a low reverse bias of 4 V.


  • Multi-Band Signal Generation Using Reconfigurable Harmonics in Coupled Oscillator Loops

    by Muhammad Waleed Mansha, Ahmed Elmenshawi, Sriram Muralidharan, Mona M. Hella

    This letter presents a configurable harmonic millimeter-wave integrated signal source architecture that leverages the dynamics of a coupled oscillator (CO) loop to selectively generate either the first, second, or third harmonic output. A startup procedure is described, to initialize the signal source in a desired mode following a random start. A proof-of-concept signal source is designed and fabricated in a 22-nm FDSOI process to demonstrate the proposed architecture. Fundamental and second harmonic signals at 77 and 154 GHz, respectively, are measured in their individual dominant oscillation modes. Six distinct oscillation modes are measured, and the oscillation frequency is tuned using the phase control in the loop, both of which validate the underlying principle of the signal source.

  • Open Access

    Broadband Vibration-Based Energy Harvesting for Wireless Sensor Applications Using Frequency Upconversion

    by Jinglun Li, Habilou Ouro-Koura, Hannah Arnow, Arian Nowbahari, Matthew Galarza, Meg Obispo, Xing Tong, Mehdi Azadmehr, Einar Halvorsen, Mona M. Hella, et al.

    Silicon-based kinetic energy converters employing variable capacitors, also known as electrostatic vibration energy harvesters, hold promise as power sources for Internet of Things devices. However, for most wireless applications, such as wearable technology or environmental and structural monitoring, the ambient vibration is often at relatively low frequencies (1–100 Hz). Since the power output of electrostatic harvesters is positively correlated to the frequency of capacitance oscillation, typical electrostatic energy harvesters, designed to match the natural frequency of ambient vibrations, do not produce sufficient power output. Moreover, energy conversion is limited to a narrow range of input frequencies. To address these shortcomings, an impacted-based electrostatic energy harvester is explored experimentally. The impact refers to electrode collision and it triggers frequency upconversion, namely a secondary high-frequency free oscillation of the electrodes overlapping with primary device oscillation tuned to input vibration frequency. The main purpose of high-frequency oscillation is to enable additional energy conversion cycles since this will increase the energy output. The devices investigated were fabricated using a commercial microfabrication foundry process and were experimentally studied. These devices exhibit non-uniform cross-section electrodes and a springless mass. The non-uniform width electrodes were used to prevent pull-in following electrode collision. Springless masses from different materials and sizes, such as 0.5 mm diameter Tungsten carbide, 0.8 mm diameter Tungsten carbide, zirconium dioxide, and silicon nitride, were added in an attempt to force collisions over a range of applied frequencies that would not otherwise result in collisions. The results show that the system operates over a relatively wide frequency range (up to 700 Hz frequency range), with the lower limit far below the natural frequency of the device. The addition of the springless mass successfully increased the device bandwidth. For example, at a low peak-to-peak vibration acceleration of 0.5 g (peak-to-peak), the addition of a zirconium dioxide ball doubled the device’s bandwidth. Testing with different balls indicates that the different sizes and material properties have different effects on the device’s performance, altering its mechanical and electrical damping.


  • A W-Band Digitally Controlled Bidirectional Transmission Line Phase Shifter in 22-nm FDSOI

    by Muhammad Waleed Mansha, Ahmed Elmenshawi, Sriram Muralidharan, Mona M. Hella

    In this letter, a passive bidirectional integrated tunable transmission line (TL) phase shifter (PS) is proposed and demonstrated in the W-band (75–110 GHz). The PS is based on a modified coplanar waveguide (CPW) structure with a conditional meandering ground return path located below the coplanar metal layer on the ground wall. The modified CPW structure achieves a wide phase shift tuning range with a compact PS unit cell A 5-bit digitally controllable PS based on the proposed topology is implemented in the 22-nm fully depleted silicon-on-insulator (FDSOI) process. The PS achieves a worst case phase resolution and loss of 4.4 $^\circ$ and 11.5 Db, respectively, in the W-band for a total phase shift of up to 115 $^\circ$ . To the authors’ knowledge, this represents the highest frequency range for a constant length integrated tunable TL PS in a silicon-based integrated circuit (IC) technology.


  • A CMOS Fully Integrated 4 × 4 VLC-Compliant Receiver Array With 2.5 Gb/s per Channel

    by Bassem Fahs, John Rollinson, Mona Mostafa Hella

    This paper presents a fully integrated 4×4 receiver array implemented in AMS 0.35 μm CMOS technology for high data rate visible-light-communication (VLC) indoor applications. Each receiver channel is composed of a digitally stabilized transimpedance amplifier, a programmable equalizer, an automatic gain-control (AGC) circuit, a programmable-gain output buffer, and a dual offset-cancellation network. The receiver exhibits 106 dBΩ maximum gain with –28 dBm 1-dB input compression power. A gain control range of 50~60 dB is achieved using a Gilbert-type linear variable-gain-amplifier (VGA). A parasitic-BJT based exponential function is employed to achieve dB-linear VGA control and an AGC constant settling time. Each of the 16 receiver channels delivers up to 3-Gb/s OOK data-rate with a VLC-compliant bit-error-rate (BER < 10-3) over a 3-m link distance with an input OOK sensitivity of –24 dBm from a 5-GHz bandwidth laser-diode at 680 nm wavelength. Extended dual-MIMO testing to a full 16-channel MIMO scenario would deliver 40 Gb/s total capacity based on the measured BER margin at 2.5 Gb/s data-rate. The receiver total area is 4.1×4.1 mm2 and each channel consumes around 230 mW from a 3.3-V DC supply.


  • Open Access

    Terahertz-Wave Absorption Gas Sensing for Dimethyl Sulfoxide

    by Alec Passarelli, Timothy E. Rice, M. Arshad Zahangir Chowdhury, Megan N. Powers, Muhammad Waleed Mansha, Ingrid Wilke, Mona M. Hella, Matthew A. Oehlschlaeger

    Gas sensing for dimethyl sulfoxide (DMSO) based on rotational absorption spectroscopy is demonstrated in the 220–330 GHz frequency range using a robust electronic THz-wave spectrometer. DMSO is a flammable liquid commonly used as a solvent in the food and pharmaceutical industries, materials synthesis, and manufacturing. DMSO is a hazard to human health and the work environment; hence, remote gas sensing for DMSO environmental and process monitoring is desired. Absorption measurements were carried out for pure DMSO at 297 K and 0.4 Torr (53 Pa). DMSO was shown to have a unique rotational fingerprint with a series of repeating absorption bands. The frequencies of transitions observed in the present study were found to be in good agreement with spectral simulations carried out based on rotational parameters derived in prior work. Newly, intensities of the rotational absorption lines were experimentally observed and reported for DMSO in this study. Measured intensities for major absorption lines were found in very good agreement with relative line intensities estimated by quantum mechanical calculations. The sensor developed here exhibited a detection limit of 1.3 × 1015–2.6 × 1015 DMSO molecules/cm3 per meter of absorption path length, with the potential for greater sensitivity with signal-to-noise improvements. The study illustrates the potential of all electronic THz-wave systems for miniaturized remote gas sensors.


  • Open Access

    IMS2022 Panel Sessions

    by Jasmin Grosinger, Mona M. Hella, Jeffrey A. Jargon

    The panel sessions at this year’s IEEE International Microwave Symposium (IMS) Week, scheduled during lunches, cover a broad range of topics and events spanning the week. Panel sessions are (co)sponsored by the IEEE Radio Frequency Integrated Circuits (RFIC) Symposium, the IEEE Microwave Theory and Techniques Society’s (MTT-S) IMS, and the Automatic Radio Frequency Techniques Group (ARFTG) Microwave Measurement Conference. The various sessions are briefly described.

  • Open Access

    Multi-Tier Heterogeneous Beam Management for Future Indoor FSO Networks

    by Michael B. Rahaim, Thomas D. C. Little, Mona Hella

    To meet the growing demand for wireless capacity, communications in the Terahertz (THz) and optical bands are being broadly explored. Communications within these bands provide massive bandwidth potential along with highly directional beam steering capabilities. While the available bandwidth offers incredible link capacity, the directionality of these technologies offers an even more significant potential for spatial capacity or area spectral efficiency. However, this directionality also implies a challenge related to the network’s ability to quickly establish a connection. In this paper, we introduce a multi-tier heterogeneous (MTH) beamform management strategy that utilizes various wireless technologies in order to quickly acquire a highly directional indoor free space optical communication (FSO) link. The multi-tier design offers the high resolution of indoor FSO while the millimeter-wave (mmWave) system narrows the FSO search space. By narrowing the search space, the system relaxes the requirements of the FSO network in order to assure a practical search time. This paper introduces the necessary components of the proposed beam management strategy and provides a foundational analysis framework to demonstrate the relative impact of coverage, resolution, and steering velocity across tiers. Furthermore, an optimization analysis is used to define the top tier resolution that minimizes worst-case search time as a function of lower tier resolution and top tier range.


  • A 220–300 GHz Twin-FET Detector for Rotational Spectroscopy of Gas Mixtures

    by Muhammad Waleed Mansha, Timothy E. Rice, Matthew A. Oehlschlaeger, Ingrid Wilke, Mona M. Hella

    In this paper, a twin-FET (field effect transistor) THz detector monolithically integrated with a dual-feed antenna is presented. The antenna-detector configuration can be extended for ’N’ FET elements to relax the input impedance requirement for the detector readout circuitry while maintaining good responsivity. A dual-feed octagonal slot antenna is used to couple THz radiation and provide differential excitation to the twin-FET detector. The multi-feed antenna-FET detector interface can be designed for an arbitrary phase excitation of one or more FET elements. Fabricated in Global Foundries 22nm FD-SOI process, the proposed detector covers a measured frequency range from 220 GHz to 300 GHz. Such bandwidth is sufficiently wide to capture reliable spectral information for distinguishing a number of gases in a mixture. The absorption spectra of pure methanol, chloromethane and acetonitrile are measured using a rotational spectroscopy setup incorporating the twin-FET detector. Detection of a small concentration of acetonitrile, at 4 Torr pressure, is demonstrated in a binary mixture with predominantly chloromethane. Detection of ethanol and methanol in their binary mixture is also demonstrated at 4 Torr pressure. This is a significant step towards the development of all-electronic THz spectroscopy for the detection of volatile organic compounds (VOCs) in the presence of contaminants with a strong THz absorption signature at > 1 Torr pressure.


  • A Thermal/RF Hybrid Energy Harvesting System With Rectifying-Combination and Improved Fractional-OCV MPPT Method

    by Zemin Liu, Yu-Pin Hsu, Mona Mostafa Hella

    This paper presents a thermal/RF hybrid energy harvester. The energy harvesting system can scavenge energy from a thermoelectric generator (TEG) and a radio-frequency (RF) energy source simultaneously, and deliver the combined power to a single load. Two techniques are employed in the system to increase the end-to-end efficiency; the rectifying-combination technique is proposed to eliminate the power loss associated with a dedicated AC-DC converter before the combiner and an improved fractional open-circuit voltage (FOCV) maximum power tracking (MPPT) is considered for a high average efficiency. A dynamic power path control extracts the maximum RF power from a cross-coupled differential rectifier, and also behaves as an AC/DC energy combiner. The thermal/RF harvester system achieves a measured peak end-to-end power conversion efficiency (PCE) of 63.4%. The shorter sampling time of 26ms every 16s for the proposed FOCV MPPT method reduces the long charging tail required to refresh the sampling capacitor, resulting in a an improved average efficiency of 82.2% for the thermal harvester. Fabricated in 0.18 μm CMOS technology, the prototype operates at a thermal input voltage ranging from 40 mV to 400 mV and an RF power from -18 dBm to -3 dBm and delivers an output voltage of 1.8 V. The total area of the fabricated circuit prototype is 1.22 mm².