Eva Bestelink
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eva Bestelink has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Radu Alexandru Sporea
Advanced Technology Institute School of Computer Science and Electronic Engineering University of Surrey Guildford UK
19 shared publications - Kham Man Niang
Department of Engineering, University of Cambridge, Cambridge, United Kingdom
4 shared publications Olivier de Sagazan
IETR-DMM-UMR6164, University of Rennes, Rennes, France
4 shared publications- Andrew John Flewitt
University of Cambridge
3 shared publications Andreï Uvarov
Corial Company, Bernin, France
2 shared publications- Benjamin Iniguez
Department of Electronics Engineering, Universitat Rovira I Virgili, Tarragona, Spain
2 shared publications
Latest Publications
- Open Access
- 6 October 2026
- Published by Wiley in Advanced Materials
- p. e75026
Contact Resistance at Interfaces Buried Within Organic Transistors Imaged Using Scanning Microwave Impedance Microscopy
Contact resistance has been a consistent challenge in the 40‐year history of the organic thin‐film transistor (OTFT). The problem arises because contact resistance at the metal electrode/organic interface is an amalgamation of physical phenomena: From ubiquitous defect states and Fermi level pinning, to the energy difference between the electrode work function and semiconductor transport level. Here, an original approach is taken to address the established OTFT contact resistance challenge. First, a new characterization technique, scanning microwave impedance microscopy (sMIM), is introduced for imaging buried metal electrode/organic interfaces. sMIM indicates contact resistance is arguably intrinsic in certain metal electrode/organic systems; namely, contact resistance exists when charge injection is theoretically Ohmic. The latter is explained by Fermi level pinning far from the organic semiconductor ionization energy, which is confirmed using ultraviolet photoelectron spectroscopy (UPS). Second, organic source‐gated transistors (OSGTs) are developed by exploiting contact resistance as a design principle. OSGTs made from small‐molecule/polymer blends, using 2,8‐difluoro‐5,11‐triethylsilylethynyl anthradithiophene (diF‐TES ADT) and poly(triarylamine) (PTAA), show distinct, low‐voltage saturation, while temperature‐dependent measurements indicate localized carriers govern charge transport. Overall, combining a new measurement technique with novel transistor operating mechanisms leads to a new approach for addressing the complex, and established, contact resistance challenge.
- 6 October 2026
- Published by Wiley in Advanced Materials
- p. e75026
Open AccessContact Resistance at Interfaces Buried Within Organic Transistors Imaged Using Scanning Microwave Impedance Microscopy
Contact resistance has been a consistent challenge in the 40‐year history of the organic thin‐film transistor (OTFT). The problem arises because contact resistance at the metal electrode/organic interface is an amalgamation of physical phenomena: From ubiquitous defect states and Fermi level pinning, to the energy difference between the electrode work function and semiconductor transport level. Here, an original approach is taken to address the established OTFT contact resistance challenge. First, a new characterization technique, scanning microwave impedance microscopy (sMIM), is introduced for imaging buried metal electrode/organic interfaces. sMIM indicates contact resistance is arguably intrinsic in certain metal electrode/organic systems; namely, contact resistance exists when charge injection is theoretically Ohmic. The latter is explained by Fermi level pinning far from the organic semiconductor ionization energy, which is confirmed using ultraviolet photoelectron spectroscopy (UPS). Second, organic source‐gated transistors (OSGTs) are developed by exploiting contact resistance as a design principle. OSGTs made from small‐molecule/polymer blends, using 2,8‐difluoro‐5,11‐triethylsilylethynyl anthradithiophene (diF‐TES ADT) and poly(triarylamine) (PTAA), show distinct, low‐voltage saturation, while temperature‐dependent measurements indicate localized carriers govern charge transport. Overall, combining a new measurement technique with novel transistor operating mechanisms leads to a new approach for addressing the complex, and established, contact resistance challenge.
- 26 August 2026
- Published by Wiley in Journal of the Society for Information Display
- Vol. 34 (11) , 866-875
Two‐Hundred‐Nanometer Bottom‐Gate/Top‐Contact Vertical‐Channel IGZO TFTs With a Non‐Lithographically Defined Channel Length
We report a bottom‐gate, top‐contact vertical‐channel In‐Ga‐Zn‐O (IGZO) thin‐film transistor (TFT) with a 200‐nm channel length defined by vertical stack thickness rather than lithographic critical‐dimension control. Conformally RF‐sputtered IGZO, together with intentionally nonconformal thermally evaporated Al contacts, enables a self‐aligned source/drain formation, whereas a SiO spacer shrinks the gate‐drain overlap capacitance by 98% without introducing ungated regions. The resulting devices achieve an on/off current ratio of , a subthreshold swing as low as 118 mV/dec, and a drive current up to 5.34 A/ m at = 2 V and = 4 V, matching or surpassing state‐of‐the‐art top‐gate vertical IGZO TFTs. Two‐dimensional TCAD simulations corroborate the measured electrostatics, clarify charge‐control mechanisms in the ultrashort vertical channel, and indicate pathways—such as contact engineering and a thinner IGZO layer—to further enhance on‐current flow and saturation. These results indicate that the proposed architecture is a promising candidate for compact active‐matrix drivers in next‐generation micro‐OLED and micro‐LED displays.
- 26 August 2026
- Published by Wiley in Journal of the Society for Information Display
- Vol. 34 (11) , 866-875
Two‐Hundred‐Nanometer Bottom‐Gate/Top‐Contact Vertical‐Channel IGZO TFTs With a Non‐Lithographically Defined Channel Length
We report a bottom‐gate, top‐contact vertical‐channel In‐Ga‐Zn‐O (IGZO) thin‐film transistor (TFT) with a 200‐nm channel length defined by vertical stack thickness rather than lithographic critical‐dimension control. Conformally RF‐sputtered IGZO, together with intentionally nonconformal thermally evaporated Al contacts, enables a self‐aligned source/drain formation, whereas a SiO spacer shrinks the gate‐drain overlap capacitance by 98% without introducing ungated regions. The resulting devices achieve an on/off current ratio of , a subthreshold swing as low as 118 mV/dec, and a drive current up to 5.34 A/ m at = 2 V and = 4 V, matching or surpassing state‐of‐the‐art top‐gate vertical IGZO TFTs. Two‐dimensional TCAD simulations corroborate the measured electrostatics, clarify charge‐control mechanisms in the ultrashort vertical channel, and indicate pathways—such as contact engineering and a thinner IGZO layer—to further enhance on‐current flow and saturation. These results indicate that the proposed architecture is a promising candidate for compact active‐matrix drivers in next‐generation micro‐OLED and micro‐LED displays.
- Open Access
- 10 January 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (4)
Pinch‐Off Mechanism of High‐Gain Organic Transistors with Field Plates: Statistical Analysis, Device Simulations and Compact Modeling
A field plate is a grounded metal layer underneath the source electrode in thin‐film transistors (TFTs) and was found to significantly reduce pinch‐off voltage and enhance intrinsic gain (up to 320) of inkjet‐printed organic TFTs. The operating mechanism was investigated through automated fabrication and statistical analysis of over 3000 devices with various channel length ( L ) and field plate length ( L fp ). Crucially, in the saturation regime, transconductance and drain current were governed by L fp rather than L . We propose and validate a new theoretical model, supported by device simulations, which demonstrates that pinch‐off occurs not at the drain or source, but at the edge of the field plate. This novel mechanism explains the observed low pinch‐off voltage and suggests that device performance can be improved through miniaturization, offering a key advantage over conventional high‐gain architectures like source‐gated transistors. In addition, the field plate enables to control pinch‐off voltage simply by layout change, providing functional versatility. Finally, a compact model was developed to facilitate the design of high‐performance printed analog circuits, highlighting the potential of these devices for future flexible electronics.
- 10 January 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (4)
Open AccessPinch‐Off Mechanism of High‐Gain Organic Transistors with Field Plates: Statistical Analysis, Device Simulations and Compact Modeling
A field plate is a grounded metal layer underneath the source electrode in thin‐film transistors (TFTs) and was found to significantly reduce pinch‐off voltage and enhance intrinsic gain (up to 320) of inkjet‐printed organic TFTs. The operating mechanism was investigated through automated fabrication and statistical analysis of over 3000 devices with various channel length ( L ) and field plate length ( L fp ). Crucially, in the saturation regime, transconductance and drain current were governed by L fp rather than L . We propose and validate a new theoretical model, supported by device simulations, which demonstrates that pinch‐off occurs not at the drain or source, but at the edge of the field plate. This novel mechanism explains the observed low pinch‐off voltage and suggests that device performance can be improved through miniaturization, offering a key advantage over conventional high‐gain architectures like source‐gated transistors. In addition, the field plate enables to control pinch‐off voltage simply by layout change, providing functional versatility. Finally, a compact model was developed to facilitate the design of high‐performance printed analog circuits, highlighting the potential of these devices for future flexible electronics.
- Open Access
- 14 February 2025
- Published by Wiley in Advanced Electronic Materials
- Vol. 11 (6)
Combinatorial Optimization and Large‐Scale Integration of Organic, Low‐Energy, and Fully‐Printed Flexible Ribbon Photosensors
The development and optimization of flexible electronics has allowed technology to be better integrated in applications and environments where the physically rigid nature of electronics is previously a limiting factor. Printing techniques contribute to lowering the fabrication costs and making manufacturing‐on‐demand viable. The use of flexible electronics in the user interface domain has been previously explored with solution‐processed optical photodetectors created and the feasibility of using flexible sensors demonstrated in augmented paper applications. In this work, low‐cost photodetectors are developed using scalable printing techniques, their electrical performance is analyzed, and their stability over time is studied both in air and in vacuum, the structure is optimized through a combinatorial optimization experiment, and a scalable integration method is demonstrated for creating larger, addressable arrays of detectors. This is a demonstration of how printing methods allow for easy, cost‐effective, and low‐energy manufacturing of uniform and stable photosensors.
- 14 February 2025
- Published by Wiley in Advanced Electronic Materials
- Vol. 11 (6)
Open AccessCombinatorial Optimization and Large‐Scale Integration of Organic, Low‐Energy, and Fully‐Printed Flexible Ribbon Photosensors
The development and optimization of flexible electronics has allowed technology to be better integrated in applications and environments where the physically rigid nature of electronics is previously a limiting factor. Printing techniques contribute to lowering the fabrication costs and making manufacturing‐on‐demand viable. The use of flexible electronics in the user interface domain has been previously explored with solution‐processed optical photodetectors created and the feasibility of using flexible sensors demonstrated in augmented paper applications. In this work, low‐cost photodetectors are developed using scalable printing techniques, their electrical performance is analyzed, and their stability over time is studied both in air and in vacuum, the structure is optimized through a combinatorial optimization experiment, and a scalable integration method is demonstrated for creating larger, addressable arrays of detectors. This is a demonstration of how printing methods allow for easy, cost‐effective, and low‐energy manufacturing of uniform and stable photosensors.
- 28 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 952-958
Physical Compact Model for Source-Gated Transistors for DC Application
We present the first physical compact model for an amorphous silicon source-gated transistor (SGT) with variable Schottky barrier height. The previously published empirical compact model and TCAD model of an SGT are used to identify dominant effects present. The compact model is then validated on real device measurements. The compact model aims to operate under common conditions and typically desirable regimes of operation for an SGT, such as the flat saturation regime occurring at a particularly low saturation voltage. The dominant injection mechanisms occur through thermionic and thermionic field emission, which are the contact effects present in an SGT. Thermionic emission tends to be dominant under most common conditions. The model is suitably accurate to be used as a representation of an SGT in a SPICE simulation. This can be seen as a first step toward analog circuit design with SGTs as compact models enable circuit designers to utilize new and unique devices.
- 28 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 952-958
Physical Compact Model for Source-Gated Transistors for DC Application
We present the first physical compact model for an amorphous silicon source-gated transistor (SGT) with variable Schottky barrier height. The previously published empirical compact model and TCAD model of an SGT are used to identify dominant effects present. The compact model is then validated on real device measurements. The compact model aims to operate under common conditions and typically desirable regimes of operation for an SGT, such as the flat saturation regime occurring at a particularly low saturation voltage. The dominant injection mechanisms occur through thermionic and thermionic field emission, which are the contact effects present in an SGT. Thermionic emission tends to be dominant under most common conditions. The model is suitably accurate to be used as a representation of an SGT in a SPICE simulation. This can be seen as a first step toward analog circuit design with SGTs as compact models enable circuit designers to utilize new and unique devices.
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (2) , 698-704
Investigation of Low-Temperature ICP-CVD µ-Si N- and P-Doped/Undoped Layers for Fully ICP-CVD Electronics
Low-temperature microcrystalline silicon ($\mu $ -Si) has been realized in a Corial inductively coupled plasma chemical vapor deposition (ICP-CVD) system. Both doped and undoped$\mu $ -Si layers have been investigated in terms of resistivity and crystalline fraction. Following a$\mu $ -Si recipe using H2/Ar/SiH4 mixture developed for plasma-enhanced chemical vapor deposition (PECVD), a technological transfer has been carried out in ICP-CVD. Some key parameters have been defined and a domain of use determined for N-type, P-type, and intrinsic layers. In the same reactor, nitride layers have also been deposited to perform gate insulator for thin-film transistors (TFTs). Finally, TFTs were fully realized by ICP-CVD and also electrically characterized, highlighting the interest of ICP-CVD for thin-film electronics. This demonstrates the great versatility of ICP-CVD technology applied to low-temperature electronic processes.- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (2) , 698-704
Investigation of Low-Temperature ICP-CVD µ-Si N- and P-Doped/Undoped Layers for Fully ICP-CVD Electronics
Low-temperature microcrystalline silicon ($\mu $ -Si) has been realized in a Corial inductively coupled plasma chemical vapor deposition (ICP-CVD) system. Both doped and undoped$\mu $ -Si layers have been investigated in terms of resistivity and crystalline fraction. Following a$\mu $ -Si recipe using H2/Ar/SiH4 mixture developed for plasma-enhanced chemical vapor deposition (PECVD), a technological transfer has been carried out in ICP-CVD. Some key parameters have been defined and a domain of use determined for N-type, P-type, and intrinsic layers. In the same reactor, nitride layers have also been deposited to perform gate insulator for thin-film transistors (TFTs). Finally, TFTs were fully realized by ICP-CVD and also electrically characterized, highlighting the interest of ICP-CVD for thin-film electronics. This demonstrates the great versatility of ICP-CVD technology applied to low-temperature electronic processes.- Open Access
- 1 December 2024
- Published by IOP Publishing in Nano Futures
- Vol. 8 (4) , 042001
Roadmap for Schottky barrier transistors
In this roadmap we consider the status and challenges of technologies that use the properties of a rectifying metal-semiconductor interface, known as a Schottky barrier (SB), as an asset for device functionality. We discuss source gated transistors, which allow for excellent electronic characteristics for low power, low frequency environmentally friendly circuits. We also consider reconfigurable field effect transistors. In such devices, two or more independent gate electrodes can be used to program different functionalities at the device level, enabling ultra-secure embedded devices. Both types of transistors can be used for neuromorphic systems, notably by combining them with ferroelectric SB transistors which enable a large number of analog states. At cryogenic temperatures SB transistors can advantageously serve for the control electronics in quantum computing devices. If the source/drain of the metallic contact becomes superconducting, Josephson junctions with a tunable phase can be realized for scalable quantum computing applications. Developing applications using SB devices requires physics-based and compact models that can be used for circuit simulations, which are also discussed. The roadmap reveals that the main challenges for these technologies are improving processing, access to industrial technologies and modeling tools for circuit simulations.
- 1 December 2024
- Published by IOP Publishing in Nano Futures
- Vol. 8 (4) , 042001
Open AccessRoadmap for Schottky barrier transistors
In this roadmap we consider the status and challenges of technologies that use the properties of a rectifying metal-semiconductor interface, known as a Schottky barrier (SB), as an asset for device functionality. We discuss source gated transistors, which allow for excellent electronic characteristics for low power, low frequency environmentally friendly circuits. We also consider reconfigurable field effect transistors. In such devices, two or more independent gate electrodes can be used to program different functionalities at the device level, enabling ultra-secure embedded devices. Both types of transistors can be used for neuromorphic systems, notably by combining them with ferroelectric SB transistors which enable a large number of analog states. At cryogenic temperatures SB transistors can advantageously serve for the control electronics in quantum computing devices. If the source/drain of the metallic contact becomes superconducting, Josephson junctions with a tunable phase can be realized for scalable quantum computing applications. Developing applications using SB devices requires physics-based and compact models that can be used for circuit simulations, which are also discussed. The roadmap reveals that the main challenges for these technologies are improving processing, access to industrial technologies and modeling tools for circuit simulations.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7530-7535
Do Contact Effects Always Mean Slow? Fast-Switching Contact-Controlled Multimodal Transistors
We investigate a mechanism for greatly improving switching speed in contact-controlled thin-film transistors (TFTs), which have persistently performed much slower than Ohmic contact variants. Separating the mechanisms for charge injection and conduction can result in transient settling times two orders of magnitude lower than existing contact-controlled devices e.g., source-gated transistor (SGT) and even lower than in Ohmic contact TFTs for a given drain current. High-speed operation is not necessarily only promoted by the well-studied reduction in contact resistance, but rather by the presence of a pre-charged accumulation layer in the source region. These findings greatly expand the applicability of contact-controlled transistors.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7530-7535
Do Contact Effects Always Mean Slow? Fast-Switching Contact-Controlled Multimodal Transistors
We investigate a mechanism for greatly improving switching speed in contact-controlled thin-film transistors (TFTs), which have persistently performed much slower than Ohmic contact variants. Separating the mechanisms for charge injection and conduction can result in transient settling times two orders of magnitude lower than existing contact-controlled devices e.g., source-gated transistor (SGT) and even lower than in Ohmic contact TFTs for a given drain current. High-speed operation is not necessarily only promoted by the well-studied reduction in contact resistance, but rather by the presence of a pre-charged accumulation layer in the source region. These findings greatly expand the applicability of contact-controlled transistors.
- 21 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (4) , 2431-2437
Optimizing a-IGZO Source-Gated Transistor Current by Structure Alteration via TCAD Simulation and Experiment
This study aims to increase the output current of the amorphous indium–gallium–zinc oxide (a-IGZO) source-gated transistor (SGT) through technology computer-aided design (TCAD) simulation and experiment. As SGT proves to be useful in various low-power applications and wearable devices, the low output current characteristics limit the adaptability of this structure. It is estimated that a higher output current level is achievable by optimizing this architecture while retaining fast saturation characteristics. The SGT structure simulations have been performed with adjusted density-of-states (DoS) parameters from experiments; this made TCAD simulation more realistic and can be used to predict the results of fabricated SGTs. The results from this study show that longer source–channel (SC) overlap and thinner channel is preferable; the SGT with longer SC overlap will result in the Mode II injection dominating over the Mode I injection. The Mode I injection occurs at the edge of source contact near the channel region, while the Mode II injection occurs at the bulk of the source at the farthest region from the channel. The result from the experiment shows that the fabricated SGT exhibits Mode II injection characteristics—that is the current will increase linearly with increasing gate voltage. From this study. it could be concluded that the SC overlap of 210 $\mu$ m with a channel thickness of 20 nm and a channel length of 5 $\mu$ m is the optimized structure that could provide high output current with little temperature dependence. Further improvement of the output current could be achieved by utilizing lower work function source metal.
- 21 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (4) , 2431-2437
Optimizing a-IGZO Source-Gated Transistor Current by Structure Alteration via TCAD Simulation and Experiment
This study aims to increase the output current of the amorphous indium–gallium–zinc oxide (a-IGZO) source-gated transistor (SGT) through technology computer-aided design (TCAD) simulation and experiment. As SGT proves to be useful in various low-power applications and wearable devices, the low output current characteristics limit the adaptability of this structure. It is estimated that a higher output current level is achievable by optimizing this architecture while retaining fast saturation characteristics. The SGT structure simulations have been performed with adjusted density-of-states (DoS) parameters from experiments; this made TCAD simulation more realistic and can be used to predict the results of fabricated SGTs. The results from this study show that longer source–channel (SC) overlap and thinner channel is preferable; the SGT with longer SC overlap will result in the Mode II injection dominating over the Mode I injection. The Mode I injection occurs at the edge of source contact near the channel region, while the Mode II injection occurs at the bulk of the source at the farthest region from the channel. The result from the experiment shows that the fabricated SGT exhibits Mode II injection characteristics—that is the current will increase linearly with increasing gate voltage. From this study. it could be concluded that the SC overlap of 210 $\mu$ m with a channel thickness of 20 nm and a channel length of 5 $\mu$ m is the optimized structure that could provide high output current with little temperature dependence. Further improvement of the output current could be achieved by utilizing lower work function source metal.
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (1) , 581-587
Promoting Low-Voltage Saturation in High-Performance a-InGaZnO Source-Gated Transistors
As oxide semiconductors increase in popularity with emerging flexible electronics, advances in material performance may lead to parasitic and nonideal effects becoming more prominent. Specifically, in source-gated transistors (SGTs), and other contact-controlled devices, the influence of the lateral drain field produced by drain bias leads to an overwhelming increase in charge density at the source edge and obliterates their signature flat saturation at low drain voltages. Here, we present high current density amorphous InGaZnO (a-IGZO) SGTs in a bottom contact architecture using Pt source and drain electrodes. The devices were fabricated by ensuring an oxygen-rich atmosphere to prevent the formation of oxygen vacancies at the Pt/a-IGZO interface. Incorporating a field relief structure within the source contact improves drain current saturation, toward behavior predicted by the saturation coefficient. In the device architecture considered, the screening was less effective for a field plate insulator thickness under 30 nm, possibly due to increased tunneling. Field plate incorporation is one of the strategies that ensures flat saturation and the suitability of contact-controlled transistors for a multitude of current driving and amplification applications.
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (1) , 581-587
Promoting Low-Voltage Saturation in High-Performance a-InGaZnO Source-Gated Transistors
As oxide semiconductors increase in popularity with emerging flexible electronics, advances in material performance may lead to parasitic and nonideal effects becoming more prominent. Specifically, in source-gated transistors (SGTs), and other contact-controlled devices, the influence of the lateral drain field produced by drain bias leads to an overwhelming increase in charge density at the source edge and obliterates their signature flat saturation at low drain voltages. Here, we present high current density amorphous InGaZnO (a-IGZO) SGTs in a bottom contact architecture using Pt source and drain electrodes. The devices were fabricated by ensuring an oxygen-rich atmosphere to prevent the formation of oxygen vacancies at the Pt/a-IGZO interface. Incorporating a field relief structure within the source contact improves drain current saturation, toward behavior predicted by the saturation coefficient. In the device architecture considered, the screening was less effective for a field plate insulator thickness under 30 nm, possibly due to increased tunneling. Field plate incorporation is one of the strategies that ensures flat saturation and the suitability of contact-controlled transistors for a multitude of current driving and amplification applications.