Łukasz Bernat
Research Subjects
Łukasz Bernat has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Arkadiusz Kroma
Division of Foundry and Plastic Working, Institute of Materials Technology, Faculty of Mechanical Engineering, Poznan University of Technology, 60-965 Poznan, Poland
1 shared publication - Grzegorz Moryson
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznan, Poland
1 shared publication - Grzegorz Wiczynski
Electronics and Lighting Engineering with the Poznań University of Technology
1 shared publication - Jakub Hajkowski
Poznan University of Technology
1 shared publication - Jan Moryson
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznan, Poland
1 shared publication - M. Hajkowski
Institute of Materials Technology Division of Foundry Poznan University of Technology Piotrowo Street 3 60-965 Poznan Poland
1 shared publication
Latest Publications
- Open Access
- 1 July 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (7) , 427-439
Analysis of fused filament fabrication / fused deposiotion modelling applications for production of casting patterns used in sand casting
This paper presents an analysis of FFF/FDM (Fused Filament Fabrication / Fused Deposiotion Modeling) applications for production of casting patterns used in sand casting, with particular emphasis on short-run and prototype production. For this purpose, casting patterns of different shape and...
- 1 July 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (7) , 427-439
Open AccessAnalysis of fused filament fabrication / fused deposiotion modelling applications for production of casting patterns used in sand casting
This paper presents an analysis of FFF/FDM (Fused Filament Fabrication / Fused Deposiotion Modeling) applications for production of casting patterns used in sand casting, with particular emphasis on short-run and prototype production. For this purpose, casting patterns of different shape and...
- Open Access
Effect of Surface Condition on the Results of Chemical Composition Measurements of Scrap Copper Alloys
The processing of copper-bearing scrap makes it possible to reduce the costs and energy consumption of obtaining copper alloy products compared to producing them from primary raw materials. To achieve this, it is necessary to quickly and accurately determine the content of alloying elements in individual scrap elements. However, the copper-bearing scrap obtained at secondary raw materials collection points consists of elements with various surface conditions (due to contamination, shape, paint coatings, roughness, etc.). The paper contains research results on the influence of surface roughness and paint coatings on the measurement result of the content of alloying elements in copper-bearing scrap. Three mobile spectrometers were used for measurements: spark-induced optical emission spectroscopy (OES), X-ray fluorescence spectrometry (XRF) and laser-induced breakdown spectroscopy (LIBS). The tests used elements with different surface roughness (from Ra = 0.03 μm to 6.7 μm) and covered with various types of varnish (alkyd, water-based, oil-phthalic, acrylic, oil-alkyd). It was found that the roughness of Ra < 2 μm does not significantly affect the results of the measurements with the OES and LIBS spectrometers, and a larger scatter of measurement results was observed for the XRF spectrometer compared to OES and LIBS. For Ra > 2 μm, a significant impact of roughness was found on the measurement results (this may result in the erroneous classification of the scrap as an incorrect material group). The influence of paint coatings on the measurement is much stronger compared to surface roughness. Even a single layer of paint can cause a change in the measurement result of the content of alloying elements by more than 10%. In the case of an OES spectrometer, paint coatings may prevent the measurement from being performed (which means that no measurement result can be acquired).
Open AccessEffect of Surface Condition on the Results of Chemical Composition Measurements of Scrap Copper Alloys
The processing of copper-bearing scrap makes it possible to reduce the costs and energy consumption of obtaining copper alloy products compared to producing them from primary raw materials. To achieve this, it is necessary to quickly and accurately determine the content of alloying elements in individual scrap elements. However, the copper-bearing scrap obtained at secondary raw materials collection points consists of elements with various surface conditions (due to contamination, shape, paint coatings, roughness, etc.). The paper contains research results on the influence of surface roughness and paint coatings on the measurement result of the content of alloying elements in copper-bearing scrap. Three mobile spectrometers were used for measurements: spark-induced optical emission spectroscopy (OES), X-ray fluorescence spectrometry (XRF) and laser-induced breakdown spectroscopy (LIBS). The tests used elements with different surface roughness (from Ra = 0.03 μm to 6.7 μm) and covered with various types of varnish (alkyd, water-based, oil-phthalic, acrylic, oil-alkyd). It was found that the roughness of Ra < 2 μm does not significantly affect the results of the measurements with the OES and LIBS spectrometers, and a larger scatter of measurement results was observed for the XRF spectrometer compared to OES and LIBS. For Ra > 2 μm, a significant impact of roughness was found on the measurement results (this may result in the erroneous classification of the scrap as an incorrect material group). The influence of paint coatings on the measurement is much stronger compared to surface roughness. Even a single layer of paint can cause a change in the measurement result of the content of alloying elements by more than 10%. In the case of an OES spectrometer, paint coatings may prevent the measurement from being performed (which means that no measurement result can be acquired).
- 15 November 2019
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 20 (1) , 5-8
Identification of Substitute Thermophysical Properties of Gypsum Mould
- 15 November 2019
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 20 (1) , 5-8
Identification of Substitute Thermophysical Properties of Gypsum Mould
- 9 May 2019
- Published by Springer Nature
- p. 195-211
Analysis of the Application of Gypsum Moulds for Casting Strength Samples of Aluminium Alloys
- 9 May 2019
- Published by Springer Nature
- p. 195-211
Analysis of the Application of Gypsum Moulds for Casting Strength Samples of Aluminium Alloys
- Open Access
- 1 December 2012
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 12 (4) , 57-64
Mechanical Properties of Al-Si-Mg Alloy Castings as a Function of Structure Refinement and Porosity Fraction
During design of the casting products technology, an important issue is a possibility of prediction of mechanical properties resulting from the course of the casting solidification process. Frequently there is a need for relations describing mechanical properties of silumin alloys as a function of phase refinement in a structure and a porosity fraction, and relations describing phase refinement in the structure and the porosity fraction as a function of solidification conditions. The study was conducted on castings of a 22 mm thick plate, made of EN AC-AlSi7Mg0,3 alloy in moulds: of quartz sand, of quartz sand with chill and in permanent moulds. On the basis of cooling curves, values of cooling rate in various casting parts were calculated. The paper also presents results of examination of distance between arms in dendrites of a solid solution α (DASL), precipitations length of silicon in an eutectic (DlSi) and gas-shrinkage porosity (Por) as a function of cooling rate. Statistical relations of DASL, DlSi, Por as a function of cooling rate and statistical multiparameter dependencies describing mechanical properties (tensile strength, yield strength, elongation) of alloy as a function of DASL, DlSi and Por are also presented in the paper.
- 1 December 2012
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 12 (4) , 57-64
Open AccessMechanical Properties of Al-Si-Mg Alloy Castings as a Function of Structure Refinement and Porosity Fraction
During design of the casting products technology, an important issue is a possibility of prediction of mechanical properties resulting from the course of the casting solidification process. Frequently there is a need for relations describing mechanical properties of silumin alloys as a function of phase refinement in a structure and a porosity fraction, and relations describing phase refinement in the structure and the porosity fraction as a function of solidification conditions. The study was conducted on castings of a 22 mm thick plate, made of EN AC-AlSi7Mg0,3 alloy in moulds: of quartz sand, of quartz sand with chill and in permanent moulds. On the basis of cooling curves, values of cooling rate in various casting parts were calculated. The paper also presents results of examination of distance between arms in dendrites of a solid solution α (DASL), precipitations length of silicon in an eutectic (DlSi) and gas-shrinkage porosity (Por) as a function of cooling rate. Statistical relations of DASL, DlSi, Por as a function of cooling rate and statistical multiparameter dependencies describing mechanical properties (tensile strength, yield strength, elongation) of alloy as a function of DASL, DlSi and Por are also presented in the paper.