Jan Moryson
Research Subjects
Jan Moryson has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Grzegorz Moryson
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznan, Poland
1 shared publication - Grzegorz Wiczynski
Electronics and Lighting Engineering with the Poznań University of Technology
1 shared publication Grzegorz Wiczyński
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznań, Poland; Poznań University of Technology, ul. Piotrowo 3A, 60-965 Poznań, Poland
1 shared publicationTomasz Jurtsch
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznan, Poland
1 shared publication- Tomasz Jurtsch
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznan, Poland
1 shared publication - Łukasz Bernat
Eko Alu sp. z o.o. sp. k., ul. Sytkowska 39, 60-413 Poznan, Poland
1 shared publication
Latest Publications
- Open Access
- 30 August 2024
- Published by Elsevier in Waste Management
- Vol. 189, 243-253
Machine vision-based detection of forbidden elements in the high-speed automatic scrap sorting line
- 30 August 2024
- Published by Elsevier in Waste Management
- Vol. 189, 243-253
Open AccessMachine vision-based detection of forbidden elements in the high-speed automatic scrap sorting line
- Open Access
Effect of Surface Condition on the Results of Chemical Composition Measurements of Scrap Copper Alloys
The processing of copper-bearing scrap makes it possible to reduce the costs and energy consumption of obtaining copper alloy products compared to producing them from primary raw materials. To achieve this, it is necessary to quickly and accurately determine the content of alloying elements in individual scrap elements. However, the copper-bearing scrap obtained at secondary raw materials collection points consists of elements with various surface conditions (due to contamination, shape, paint coatings, roughness, etc.). The paper contains research results on the influence of surface roughness and paint coatings on the measurement result of the content of alloying elements in copper-bearing scrap. Three mobile spectrometers were used for measurements: spark-induced optical emission spectroscopy (OES), X-ray fluorescence spectrometry (XRF) and laser-induced breakdown spectroscopy (LIBS). The tests used elements with different surface roughness (from Ra = 0.03 μm to 6.7 μm) and covered with various types of varnish (alkyd, water-based, oil-phthalic, acrylic, oil-alkyd). It was found that the roughness of Ra < 2 μm does not significantly affect the results of the measurements with the OES and LIBS spectrometers, and a larger scatter of measurement results was observed for the XRF spectrometer compared to OES and LIBS. For Ra > 2 μm, a significant impact of roughness was found on the measurement results (this may result in the erroneous classification of the scrap as an incorrect material group). The influence of paint coatings on the measurement is much stronger compared to surface roughness. Even a single layer of paint can cause a change in the measurement result of the content of alloying elements by more than 10%. In the case of an OES spectrometer, paint coatings may prevent the measurement from being performed (which means that no measurement result can be acquired).
Open AccessEffect of Surface Condition on the Results of Chemical Composition Measurements of Scrap Copper Alloys
The processing of copper-bearing scrap makes it possible to reduce the costs and energy consumption of obtaining copper alloy products compared to producing them from primary raw materials. To achieve this, it is necessary to quickly and accurately determine the content of alloying elements in individual scrap elements. However, the copper-bearing scrap obtained at secondary raw materials collection points consists of elements with various surface conditions (due to contamination, shape, paint coatings, roughness, etc.). The paper contains research results on the influence of surface roughness and paint coatings on the measurement result of the content of alloying elements in copper-bearing scrap. Three mobile spectrometers were used for measurements: spark-induced optical emission spectroscopy (OES), X-ray fluorescence spectrometry (XRF) and laser-induced breakdown spectroscopy (LIBS). The tests used elements with different surface roughness (from Ra = 0.03 μm to 6.7 μm) and covered with various types of varnish (alkyd, water-based, oil-phthalic, acrylic, oil-alkyd). It was found that the roughness of Ra < 2 μm does not significantly affect the results of the measurements with the OES and LIBS spectrometers, and a larger scatter of measurement results was observed for the XRF spectrometer compared to OES and LIBS. For Ra > 2 μm, a significant impact of roughness was found on the measurement results (this may result in the erroneous classification of the scrap as an incorrect material group). The influence of paint coatings on the measurement is much stronger compared to surface roughness. Even a single layer of paint can cause a change in the measurement result of the content of alloying elements by more than 10%. In the case of an OES spectrometer, paint coatings may prevent the measurement from being performed (which means that no measurement result can be acquired).