XCXuehui Chen

Xuehui Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xuehui Chen has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wind induced structural response analysis of photovoltaic tracking supports by unidirectional fluid structure coupling

    by Darong Zhu, Yan Liu, Tao Ma, Wei Liu, Xuehui Chen

    To investigate the wind-induced vibration characteristics of photovoltaic array tracking supports, this study uses the harmonic superposition method to simulate pulsating wind time series and, combined with fluid–structure coupling technology, analyzes the wind pressure distribution and the response to wind-induced vibration under various wind directions and tilt angles. The study finds that: the wind pressure distribution is uneven, with the first-row modules being most affected by the wind load, while the wind pressure in the rear rows decreases due to the row effect. The displacement response of the first-row modules is the largest, the second row exhibits the greatest attenuation, and the displacement in the subsequent rows tends to stabilize. Additionally, the vibration displacement of the purlins is the largest, while the main beam and columns exhibit relatively smaller displacements, indicating substantial differences in the dynamic responses of different components of the support structure under wind loading.


  • EFFECT OF LASER SURFACE REMELTING OF 304 STAINLESS STEEL

    by Yu. Chen, X. Li, J. Liu, Y. Zhang, X. Chen

    To study the effect of laser surface remelting (LSR) on the organization and properties of a 304 stainless steel surface layer, the microscopic morphology, hardness, roughness, adhesion, and corrosion resistance of the remelted layer (RL) are examined by changing the laser scanning speed (LSS). The experimental results show that the LSR technique hardens the 304 stainless steel substrate surface with a substrate hardness of 185 HV, and the maximum hardness after remelting is 248.9 HV. With an increase in the LSS, the surface roughness gradually decreases, while the bonding force first increases and then decreases, with the maximum bonding force being 26.1 N. At the LSS of 20 mm/s, the phase distribution in the RL is more uniform. The maximum self-corrosion potential of the RL reaches −0.718 V, and the self-corrosion current density is 3.872 A/cm2. The surface properties of 304 stainless steel are improved by using LSR.


  • Effects of different processing parameters on laser water jet-machining silicon

    by Y. Chen, X. Li, X. Chen, H. Li

    Laser water jet processing is a new hybrid method developed on the basis of traditional laser processing technology. It combines high laser processing efficiency with the impact and cooling effects of water jets. Laser water jet processing can effectively process hard and brittle materials such as silicon. In-depth study of the processing technology has important practical significance. For this reason, the controlled variable method is used to study the influence of different processing parameters on groove depth. The research results show that with the increase of current and laser pulse width, the groove depth gradually increases; with the increase of laser repetition frequency and water jet velocity, the groove depth increases first and then decreases. The experiment of laser water jet processing silicon can provide guidance for processing other difficult-to-process materials in the future.


  • Open Access

    Effect of Scanning Speed on Properties of Laser Surface Remelted 304 Stainless Steel

    by Yuanlong Chen, Xiang Li, Jinyang Liu, Yichi Zhang, Xuehui Chen

    In order to study the microstructure and properties of stainless steel after laser surface remelting, based on the theory of laser surface remelting, a simulation model of nanosecond-pulsed laser surface remelted stainless steel was established to study the evolution law of the Marangoni force of the molten pool during laser surface remelting. A single-lane laser remelting experiment was performed to study the variation of the scanning speed on the remelting width, roughness, and layer microtopography. The “S” scanning path was used to remelt the stainless steel surface to investigate the bonding force between the remelted layer and the substrate, the hardness, microscopic morphology, and corrosion resistance. The results show that the viscosity of the liquid metal in the molten pool increases with the increase of the scanning speed. Larger liquid viscosity and smaller surface tension temperature gradients promote a weaker flow of liquid metal, which reduces the velocity of the liquid metal flow in the molten pool. With the increase of scanning speed, the remelting width gradually decreases, but the roughness gradually increases. When the element content of Cr increases, the element content of Fe and O decreases. The surface is covered with an oxide film, the main components of which are oxides of Cr and Fe, the remelted layer is greater than that of the substrate, and the corrosion resistance is improved. Laser surface remelting technology can improve the structure and properties of 304 stainless steel.


  • Open Access

    Effects of Laser Machining Aluminum Alloy in Different Media

    by Xiang Li, Shan Huang, Jianping Tang, Weihao Mu, Xin Xu, Xuehui Chen

    To study the effects of aluminum alloys processed by a laser in air and water and at different water velocities, corresponding experiments were conducted and the impacting effects of different water velocities on the surface of the workpiece were simulated, respectively. The results show that when laser processing aluminum alloy materials in air, there is more slag and a recondensation layer on both sides of the groove, the heat-affected zone is larger and the surface processing quality is poor. When laser processing aluminum alloy materials in water, the processing quality is improved. With the increase in water velocity, the impacting and cooling effect is enhanced, the groove depth and groove width show a trend of first increasing and then decreasing, the slag and recondensation layer on both sides of the groove are reduced, the heat-affected zone is reduced and the processing quality of the groove is improved. When the water velocity reaches 30 m/s, a better groove can be obtained. Laser processing aluminum alloy materials in water can obtain better processing quality than laser processing in air.


  • Open Access

    Liquid-Infused Microgrooved Slippery Surface Ablated by One-Step Laser Irradiation for Underwater Bubble Directional Manipulation and Anisotropic Spreading

    by Wei Liu, Xuehui Chen, Yunlong Jiao

    A pitcher plant is a kind of liquid-infused porous surface that imparts an excellent directional manipulation ability to in-air droplets or underwater bubbles, so it has attracted researchers’ attention in both academic and industrial issues. In this work, a kind of liquid-infused anisotropic microgrooved slippery surface (LIAMSS) was fabricated through one-step femtosecond laser irradiation and lubricant coating technology. On the inclined LIAMSS, the underwater bubbles show great directional motion and anisotropic spreading ability under the effect of buoyancy. It should be noted that the interaction between the air and the lubricant layer plays a dominant role in determining the attachment and the movement of the underwater bubble, which could be ascribed to the competition between the adhesion resistance induced by contact angle hysteresis and the drive force induced by buoyancy. Additionally, the bubble shows obvious anisotropy on the LIAMSS with the increase in volume because of the restriction of the slippery area, and the bubble contact angle perpendicular to the grooved region is about 88○ when the bubble volume is 5 μL. We believe that the present findings would accelerate the application of this kind of bubble slippery surface in underwater gas collection and tail gas treatment.


  • Open Access

    Study on Femtosecond Laser Processing Characteristics of Nano-Crystalline CVD Diamond Coating

    by Chao Wei, Yuping Ma, Yuan Han, Yao Zhang, Liu Yang, Xuehui Chen

    Ultra-short pulse laser interaction with diamond materials has attracted extensive interest in micro- and nano-machining, especially for the fabrication of micro tools, because of the straightforward method and high precision. Thanks to the development of chemical vapor deposition (CVD) technology, high-quality CVD diamonds are employed in more varieties of tools as performance-enhancing coatings. The purpose of the experiments reported here was to explore the machinability of CVD diamond coating under the irradiation of femtosecond (fs) pulsed laser. The factor-control approach was adopted to investigate the influence of scanning speed, single pulse energy and repetition rate on the surface quality and carbon phase transition of CVD diamond coating. The material removal rate and surface roughness were evaluated. The interaction mechanism of scanning speed, single pulse energy, and repetition rate were discussed, and the fs laser ablation threshold of CVD diamond coating was calculated. It was demonstrated that two ablation mechanisms (weak and intensive) were in existence as evidenced by the distinct surface morphologies induced under different processing conditions. A strong dependence on the variation of scanning speed and pulse energy is identified in the examination of surface roughness and removal rate. Lorentzian–Gaussian deconvolution of Raman spectra illustrates that fs laser irradiation yields a strong modification effect on the coating and release the compressive stress in it. Furthermore, a newly defined parameter referring to the fs laser energies applied to unit volume was introduced to depict the degree of ablation and the Taguchi method was used to figure out the significance of different parameters. The ablation threshold of CVD diamond coating at the effective pulses of 90 is calculated to be 0.138 J/cm2.


  • Open Access

    Optimization of Processing Parameters for Water-Jet-Assisted Laser Etching of Polycrystalline Silicon

    by Xuehui Chen, Xiang Li, Chao Wu, Yuping Ma, Yao Zhang, Lei Huang, Wei Liu

    Liquid-assisted laser technology is used to etch defect-free materials for high-precision electronics and machinery. This study investigates water-jet-assisted laser etching of polysilicon material. The depths and widths of the etched grooves were investigated for different water-jet incident angles and velocities. To select optimal parameters for a composite etching processing, the results of many tests must be compared, and at least one set of good processing parameter combinations must be identified. Herein, the influence of different parameters on the processing results is studied using an orthogonal test method. The results demonstrate that the depths and widths of the processing grooves were nearly identical at water-jet angles of 30°and 60°; however, the 60° incidence conferred a slight advantage over 30° incidence. The section taper, section depth, and surface topography were optimized at a water-jet velocity of 24-m/s, 1.1-ms laser pulse width, 40-Hz frequency, and 180-A current. Under these conditions, the section taper and groove depth were 1.2° and 1.88 mm, respectively. The groove surfaces exhibited no splitting, slagging, or other defects, and no recast layers were visible.