Chengquan Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chengquan Hu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Hongen Liao
Tsinghua University
6 shared publications - Jiayuan Liu
Tsinghua University, Beijing, China
4 shared publications - Boyu Zhang
School of Biomedical engineering, Shanghai Jiaotong University, Shanghai, China
3 shared publications - Jie Wang
School of Biomedical Engineering, Tsinghua University, Beijing, China
3 shared publications - Jingyi Kang
School of Materials Science and Engineering, Tsinghua University, Beijing, China
3 shared publications - Longfei Ma
School of Biomedical Engineering, Tsinghua University, Beijing, China
2 shared publications
Latest Publications
- 10 September 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (10) , 105017
Spring-reinforced pneumatic actuator and soft robotic applications
Compared to rigid-structure robots, soft robots possess higher degrees of freedom and stronger environmental adaptability, which has aroused increasing attention in the robotic field. Among them, soft pneumatic robots have excellent performances in various practical applications. However, the nonlinearity and instability of pressure response of soft actuators caused by lateral expansion come to a great challenge. To address this problem, we proposed to embed a spring constraint layer around each single air chamber. Following the design concept, we obtained single-cavity and multi-DoF pneumatic actuators and evaluated their elongation and bending characteristics. Experimental results demonstrated that our proposed actuators have more linear pressure response as well as higher consistency. Eventually, through robotic applications, including soft robotic hand and gripper our proposed actuators could facilitate flexible manipulation and elaborate performance.
- 10 September 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (10) , 105017
Spring-reinforced pneumatic actuator and soft robotic applications
Compared to rigid-structure robots, soft robots possess higher degrees of freedom and stronger environmental adaptability, which has aroused increasing attention in the robotic field. Among them, soft pneumatic robots have excellent performances in various practical applications. However, the nonlinearity and instability of pressure response of soft actuators caused by lateral expansion come to a great challenge. To address this problem, we proposed to embed a spring constraint layer around each single air chamber. Following the design concept, we obtained single-cavity and multi-DoF pneumatic actuators and evaluated their elongation and bending characteristics. Experimental results demonstrated that our proposed actuators have more linear pressure response as well as higher consistency. Eventually, through robotic applications, including soft robotic hand and gripper our proposed actuators could facilitate flexible manipulation and elaborate performance.
- 11 June 2024
- Published by Springer Nature in International Journal of Computer Assisted Radiology and Surgery
- Vol. 19 (8) , 1495-1504
A robot-assisted tracheal intubation system based on a soft actuator
Purpose Tracheal intubation is the gold standard of airway protection and constitutes a pivotal life-saving technique frequently employed in emergency medical interventions. Hence, in this paper, a system is designed to execute tracheal intubation tasks automatically, offering a safer and more efficient solution, thereby alleviating the burden on physicians. Methods The system comprises a tracheal tube with a bendable front end, a drive system, and a tip endoscope. The soft actuator provides two degrees of freedom for precise orientation. It is fabricated with varying-hardness silicone and reinforced with fibers and spiral steel wire for flexibility and safety. The hydraulic actuation system and tube feeding mechanism enable controlled bending and delivery. Object detection of key anatomical features guides the robotic arm and soft actuator. The control strategy involves visual servo control for coordinated robotic arm and soft actuator movements, ensuring accurate and safe tracheal intubation. Results The kinematics of the soft actuator were established using a constant curvature model, allowing simulation of its workspace. Through experiments, the actuator is capable of 90° bending as well as 20° deflection on the left and right sides. The maximum insertion force of the tube is 2 N. Autonomous tracheal intubation experiments on a training manikin were successful in all 10 trials, with an average insertion time of 45.6 s. Conclusion Experimental validation on the manikin demonstrated that the robot tracheal intubation system based on a soft actuator was able to perform safe, stable, and automated tracheal intubation. In summary, this paper proposed a safe and automated robot-assisted tracheal intubation system based on a soft actuator, showing considerable potential for clinical applications.
- 11 June 2024
- Published by Springer Nature in International Journal of Computer Assisted Radiology and Surgery
- Vol. 19 (8) , 1495-1504
A robot-assisted tracheal intubation system based on a soft actuator
Purpose Tracheal intubation is the gold standard of airway protection and constitutes a pivotal life-saving technique frequently employed in emergency medical interventions. Hence, in this paper, a system is designed to execute tracheal intubation tasks automatically, offering a safer and more efficient solution, thereby alleviating the burden on physicians. Methods The system comprises a tracheal tube with a bendable front end, a drive system, and a tip endoscope. The soft actuator provides two degrees of freedom for precise orientation. It is fabricated with varying-hardness silicone and reinforced with fibers and spiral steel wire for flexibility and safety. The hydraulic actuation system and tube feeding mechanism enable controlled bending and delivery. Object detection of key anatomical features guides the robotic arm and soft actuator. The control strategy involves visual servo control for coordinated robotic arm and soft actuator movements, ensuring accurate and safe tracheal intubation. Results The kinematics of the soft actuator were established using a constant curvature model, allowing simulation of its workspace. Through experiments, the actuator is capable of 90° bending as well as 20° deflection on the left and right sides. The maximum insertion force of the tube is 2 N. Autonomous tracheal intubation experiments on a training manikin were successful in all 10 trials, with an average insertion time of 45.6 s. Conclusion Experimental validation on the manikin demonstrated that the robot tracheal intubation system based on a soft actuator was able to perform safe, stable, and automated tracheal intubation. In summary, this paper proposed a safe and automated robot-assisted tracheal intubation system based on a soft actuator, showing considerable potential for clinical applications.
- 18 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (3) , 2120-2127
Peristaltic Pump-Based Palm-Sized Multi-Mode Pressure Supply System for Soft Robots
Soft robots have garnered considerable interest in recent years in terms of structure and functionality, while commercially viable pressure supply systems with various pressure supply modes for soft robots remain slow to progress. Hence, in this work, a palm-sized multi-mode pressure supply system based on a peristaltic pump is proposed for the first time, and precise pneumatic pressure control is achieved with a model reference adaptive control (MRAC) method based on the system dynamics. Further performance evaluation demonstrates that our system can deliver precise positive (mean error < 0.48 kPa for 0 $\sim$ 50 kPa) and negative pressures (mean error < 0.85 kPa for −50 $\sim$ 0 kPa) with minimal fluctuations, which outperforms the PID method. Application experiments indicate that our system can accommodate various pressure supply requirements, including controllable pressurization and depressurization, and has the potential for both pneumatic and hydraulic applications. In addition, by incorporating the MRAC method into the system, we have achieved excellent stability and high repeatability in controlling the position of a retractable soft pneumatic actuator, thus demonstrating the system's high accuracy and repeatability in pressure output. The phantom experiment of the injection soft robotic system further validates the system's diverse pressure supply capabilities for complex manipulations of soft robots.
- 18 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (3) , 2120-2127
Peristaltic Pump-Based Palm-Sized Multi-Mode Pressure Supply System for Soft Robots
Soft robots have garnered considerable interest in recent years in terms of structure and functionality, while commercially viable pressure supply systems with various pressure supply modes for soft robots remain slow to progress. Hence, in this work, a palm-sized multi-mode pressure supply system based on a peristaltic pump is proposed for the first time, and precise pneumatic pressure control is achieved with a model reference adaptive control (MRAC) method based on the system dynamics. Further performance evaluation demonstrates that our system can deliver precise positive (mean error < 0.48 kPa for 0 $\sim$ 50 kPa) and negative pressures (mean error < 0.85 kPa for −50 $\sim$ 0 kPa) with minimal fluctuations, which outperforms the PID method. Application experiments indicate that our system can accommodate various pressure supply requirements, including controllable pressurization and depressurization, and has the potential for both pneumatic and hydraulic applications. In addition, by incorporating the MRAC method into the system, we have achieved excellent stability and high repeatability in controlling the position of a retractable soft pneumatic actuator, thus demonstrating the system's high accuracy and repeatability in pressure output. The phantom experiment of the injection soft robotic system further validates the system's diverse pressure supply capabilities for complex manipulations of soft robots.
- 31 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 8 (9) , 5704-5711
A Miniaturized Variable Stiffness Soft Manipulator With a Customizable LMPA Pattern
Safe human-robot interaction and excellent motion flexibility ensure a wide range of potential applications for soft robots in industry and medicine. Although many efforts have been made to empower soft robots with variable stiffness, solutions for miniaturization, wide-range, and rapid-response stiffness have yet to be realized. To maintain the combination of motion flexibility and operation stability, in this work a soft variable stiffness manipulator with a diameter of 10.7 mm based on a low melting point alloy (LMPA) solution is proposed. Inspired by reinforced concrete structures, LMPA structures can be freely designed and optimized by a novel 2D to 3D fabrication method for the first time. The crossed pattern LMPA was selected as the variable stiffness skeleton of the manipulator through comparative experiments. Under hot and cold water circulation, the rigid-soft transition time is reduced to 10–15 seconds due to structure optimization. Tests have shown that the omnidirectional steering manipulator can easily be bent over $180^{\circ }$ with high repeatability (standard deviation of $1.37^{\circ }$ ) in the soft state and lock the shape at any bend angle with a stiffness of about 415.45 N/m in the rigid state. The rapid and wide variation in stiffness of the soft manipulator can be used as a small platform for minimally invasive surgical tools in confined spaces.
- 31 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 8 (9) , 5704-5711
A Miniaturized Variable Stiffness Soft Manipulator With a Customizable LMPA Pattern
Safe human-robot interaction and excellent motion flexibility ensure a wide range of potential applications for soft robots in industry and medicine. Although many efforts have been made to empower soft robots with variable stiffness, solutions for miniaturization, wide-range, and rapid-response stiffness have yet to be realized. To maintain the combination of motion flexibility and operation stability, in this work a soft variable stiffness manipulator with a diameter of 10.7 mm based on a low melting point alloy (LMPA) solution is proposed. Inspired by reinforced concrete structures, LMPA structures can be freely designed and optimized by a novel 2D to 3D fabrication method for the first time. The crossed pattern LMPA was selected as the variable stiffness skeleton of the manipulator through comparative experiments. Under hot and cold water circulation, the rigid-soft transition time is reduced to 10–15 seconds due to structure optimization. Tests have shown that the omnidirectional steering manipulator can easily be bent over $180^{\circ }$ with high repeatability (standard deviation of $1.37^{\circ }$ ) in the soft state and lock the shape at any bend angle with a stiffness of about 415.45 N/m in the rigid state. The rapid and wide variation in stiffness of the soft manipulator can be used as a small platform for minimally invasive surgical tools in confined spaces.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 28 (5) , 2716-2727
A Novel Miniature Spring-Based Continuum Manipulator for Minimally Invasive Surgery: Design and Evaluation
Minimally invasive surgery is gaining wide-spread attention in the laboratory and the clinic due to its advantages of less trauma, less pain, and faster recovery. Miniature continuum instruments with a large central channel are needed for reducing damage to healthy tissue and delivering multiple surgical tools in microsurgery such as fetal surgery and maxillary sinus surgery. In this article, we proposed a novel miniature spring-based cable-driven continuum manipulator characterized by its offset neutral bending plane and its simple and clever structure. These features enable the manipulator to have several advantages such as easy miniaturization, bending stability and uniformity, a large central channel, smaller cable tension required, and low cost. A piecewise constant curvature model, with the offset neutral bending plane taken into account, is presented for the kinematic control of the proposed manipulator. To explore the relationship between the cable tension and manipulator bending angle, the statics model based on the equivalent model principle, is exhaustively discussed. The accuracy of kinematics and statics models, as well as the design superiority, was verified experimentally. Furthermore, teleoperation experiments of peg-transfer tasks and porcine tissue laser ablation are conducted to verify the feasibility and effectiveness of the proposed manipulator in different forms. Final, design variations are showcased to enrich manipulator design and functionality.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 28 (5) , 2716-2727
A Novel Miniature Spring-Based Continuum Manipulator for Minimally Invasive Surgery: Design and Evaluation
Minimally invasive surgery is gaining wide-spread attention in the laboratory and the clinic due to its advantages of less trauma, less pain, and faster recovery. Miniature continuum instruments with a large central channel are needed for reducing damage to healthy tissue and delivering multiple surgical tools in microsurgery such as fetal surgery and maxillary sinus surgery. In this article, we proposed a novel miniature spring-based cable-driven continuum manipulator characterized by its offset neutral bending plane and its simple and clever structure. These features enable the manipulator to have several advantages such as easy miniaturization, bending stability and uniformity, a large central channel, smaller cable tension required, and low cost. A piecewise constant curvature model, with the offset neutral bending plane taken into account, is presented for the kinematic control of the proposed manipulator. To explore the relationship between the cable tension and manipulator bending angle, the statics model based on the equivalent model principle, is exhaustively discussed. The accuracy of kinematics and statics models, as well as the design superiority, was verified experimentally. Furthermore, teleoperation experiments of peg-transfer tasks and porcine tissue laser ablation are conducted to verify the feasibility and effectiveness of the proposed manipulator in different forms. Final, design variations are showcased to enrich manipulator design and functionality.
- 17 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (3) , 2645-2652
Design and Modularization of Multi-DoF Soft Robotic Actuators
Soft robotic technologies offer a promising solution for unconstructed applications due to their complete softness, robustness and flexibility. In this letter, we explore the design and modularization of the flexible pneumatic robotic actuators designed for applications in minimally invasive surgery or other constrained spaces. We first identify the basic multi-cavity structure and subsequently explore three basic morphologies of the multi-DoF actuator, which are differentiated by the shapes of their inner chambers. The corresponding fabrication methods are developed to create the standard fabrication processes for such complicated structures. Furthermore, we propose the modular concept and method of assembling these actuators into flexible robotic manipulators for different applications. Results show that the fabrication methods are suitable for the corresponding different chamber structures and are adaptive for fabricating multiple scales from the miniature size (diameter of 3.5 mm) to larger size. Detailed characterizations show that the multi-DoF actuators can freely adjust the heading direction in the three dimensional space. Additionally, application experiments show that the modular design achieves to rapidly assemble flexible robotic manipulators, which are potential in future applications that require closer inspection and manipulation.
- 17 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (3) , 2645-2652
Design and Modularization of Multi-DoF Soft Robotic Actuators
Soft robotic technologies offer a promising solution for unconstructed applications due to their complete softness, robustness and flexibility. In this letter, we explore the design and modularization of the flexible pneumatic robotic actuators designed for applications in minimally invasive surgery or other constrained spaces. We first identify the basic multi-cavity structure and subsequently explore three basic morphologies of the multi-DoF actuator, which are differentiated by the shapes of their inner chambers. The corresponding fabrication methods are developed to create the standard fabrication processes for such complicated structures. Furthermore, we propose the modular concept and method of assembling these actuators into flexible robotic manipulators for different applications. Results show that the fabrication methods are suitable for the corresponding different chamber structures and are adaptive for fabricating multiple scales from the miniature size (diameter of 3.5 mm) to larger size. Detailed characterizations show that the multi-DoF actuators can freely adjust the heading direction in the three dimensional space. Additionally, application experiments show that the modular design achieves to rapidly assemble flexible robotic manipulators, which are potential in future applications that require closer inspection and manipulation.