Daniel Bernal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daniel Bernal has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Iñaki Hurtado
Mechanical and Manufacturing Department, Mondragon University, Loramendi 4, E20500 Arrasate-Mondragon, Gipuzkoa, Spain
5 shared publications - Xabier Chamorro
Mechanical and Manufacturing Department, Mondragon University, Loramendi 4, 20500 Mondragon, Gipuzkoa, Spain
5 shared publications - Iñaki Madariaga
Materials and Processes Department, Industria de Turbopropulsores, SAU, Parque Tecnológico No 300, 48170 Zamudio, Spain
2 shared publications - Alberto Cobos
LORTEK Technological Centre, Basque Research and Technology Alliance (BRTA), Ordizia, Spain
1 shared publication - Andrea Niklas
Fundación AZTERLAN, Basque Research and Technology Alliance (BRTA), Aliendalde Auzunea 6, 48200 Durango, Spain
1 shared publication - David Bürger
Institute for Materials, Ruhr University Bochum, Universitätsstr. 150, 44801 Bochum, Germany
1 shared publication
Latest Publications
- Open Access
- 6 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 3351-3361
Effect of the crucible composition on the Inconel 718 vacuum induction melting process efficiency
- 6 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 3351-3361
Open AccessEffect of the crucible composition on the Inconel 718 vacuum induction melting process efficiency
- Open Access
Integration of Hot Isostatic Pressing and Heat Treatment for Advanced Modified γ-TiAl TNM Alloys
The conventional processing route of TNM (Ti-Nb-Mo) alloys combines casting and Hot Isostatic Pressing (HIP) followed by forging and multiple heat treatments to establish optimum properties. This is a time-consuming and costly process. In this study we present an advanced alternative TNM alloy processing route combining HIP and heat treatments into a single process, which we refer to as IHT (integrated HIP heat treatment), applied to a modified TNM alloy with 1.5B. A Quintus HIP lab unit with a quenching module was used, achieving fast and controlled cooling, which differs from the slow cooling rates of conventional HIP units. A Ti-42.5Al-3.5Nb-1Mo-1.5B (at.%) was subjected to an integrated two HIP steps at 200 MPa, one at 1250 °C for 3 h and another at 1260 °C for 1 h, both under a protective Ar atmosphere and followed by cooling at 30 K/min down to room temperature. The results were compared against the Ti-43.5Al-3.5Nb-1Mo-0.8B (at.%) thermomechanically processed in a conventional way. Applying IHT processing to the 1.5B alloy does indeed achieve good creep strength, and the secondary creep rate of the IHT processed materials is similar to that of conventionally forged TNM alloys. Thus, the proposed advanced IHT processing route could manufacture more cost-effective TiAl components.
Open AccessIntegration of Hot Isostatic Pressing and Heat Treatment for Advanced Modified γ-TiAl TNM Alloys
The conventional processing route of TNM (Ti-Nb-Mo) alloys combines casting and Hot Isostatic Pressing (HIP) followed by forging and multiple heat treatments to establish optimum properties. This is a time-consuming and costly process. In this study we present an advanced alternative TNM alloy processing route combining HIP and heat treatments into a single process, which we refer to as IHT (integrated HIP heat treatment), applied to a modified TNM alloy with 1.5B. A Quintus HIP lab unit with a quenching module was used, achieving fast and controlled cooling, which differs from the slow cooling rates of conventional HIP units. A Ti-42.5Al-3.5Nb-1Mo-1.5B (at.%) was subjected to an integrated two HIP steps at 200 MPa, one at 1250 °C for 3 h and another at 1260 °C for 1 h, both under a protective Ar atmosphere and followed by cooling at 30 K/min down to room temperature. The results were compared against the Ti-43.5Al-3.5Nb-1Mo-0.8B (at.%) thermomechanically processed in a conventional way. Applying IHT processing to the 1.5B alloy does indeed achieve good creep strength, and the secondary creep rate of the IHT processed materials is similar to that of conventionally forged TNM alloys. Thus, the proposed advanced IHT processing route could manufacture more cost-effective TiAl components.
- 1 September 2020
- Published by Elsevier in Intermetallics
- Vol. 124, 106842
Evolution of lamellar microstructures in a cast TNM alloy modified with boron through single-step heat treatments
- 1 September 2020
- Published by Elsevier in Intermetallics
- Vol. 124, 106842
Evolution of lamellar microstructures in a cast TNM alloy modified with boron through single-step heat treatments
- Open Access
Effect of Boron Content and Cooling Rate on the Microstructure and Boride Formation of β-Solidifying γ-TiAl TNM Alloy
Boron is a unique and popular grain refiner element in cast titanium aluminide (TiAl) alloys, as it helps to improve mechanical properties if properly alloyed. However, the formation mechanism of different types of borides in cast TiAl alloys is not yet clearly understood. This study seeks to correlate the chemical composition and cooling rate during solidification of cast TiAl alloys, with the type of boride precipitated and the resulting microstructure. Several β-solidifying γ-TiAl alloys of the TNM family were cast, alloying boron to a starting Ti-44.5Al-4Nb-1Mo-0.1B (at.%) alloy. The alloys were manufactured with an induction skull melting furnace and poured into a stepped 2, 4, 8 and 16 mm thickness mold to achieve different cooling rates. On one hand, the results reveal that boron contents below 0.5 at.% and cooling rates during solidification above 10 K/s promote the formation of detrimental ribbon borides. On the other hand, boron contents above 0.5 at.% and cooling rates during solidification below 10 K/s promote the formation of a refined microstructure with blocky borides. Finally, the formation mechanisms of both ribbon and blocky borides are proposed.
Open AccessEffect of Boron Content and Cooling Rate on the Microstructure and Boride Formation of β-Solidifying γ-TiAl TNM Alloy
Boron is a unique and popular grain refiner element in cast titanium aluminide (TiAl) alloys, as it helps to improve mechanical properties if properly alloyed. However, the formation mechanism of different types of borides in cast TiAl alloys is not yet clearly understood. This study seeks to correlate the chemical composition and cooling rate during solidification of cast TiAl alloys, with the type of boride precipitated and the resulting microstructure. Several β-solidifying γ-TiAl alloys of the TNM family were cast, alloying boron to a starting Ti-44.5Al-4Nb-1Mo-0.1B (at.%) alloy. The alloys were manufactured with an induction skull melting furnace and poured into a stepped 2, 4, 8 and 16 mm thickness mold to achieve different cooling rates. On one hand, the results reveal that boron contents below 0.5 at.% and cooling rates during solidification above 10 K/s promote the formation of detrimental ribbon borides. On the other hand, boron contents above 0.5 at.% and cooling rates during solidification below 10 K/s promote the formation of a refined microstructure with blocky borides. Finally, the formation mechanisms of both ribbon and blocky borides are proposed.
- Open Access
Induction Skull Melting of Ti-6Al-4V: Process Control and Efficiency Optimization
Titanium investment casting is one of the leading and most efficient near-net-shape manufacturing processes, since complex shape components are possible to obtain with a very low amount of material waste. But melting these reactive alloys implies the usage of specific melting technologies such as the Induction Skull Melting (ISM) method. In this work the ISM was extensively studied with the aim of deepening the characteristics of this specific melting method and improving the too low energy efficiency and overall process performance. A 16 segment copper crucible and 3 turns coil was employed for the melting of 1 kg of Ti-6Al-4V alloy. Through the calorimetric balance, real-time evolution of the process parameters and power losses arising from the crucible and coil sub-assemblies was displayed. Results revealed the impact of coil working conditions in the overall ISM thermal efficiency and titanium melt properties, revealing the use of these conditions as an effective optimization strategy. This unstudied melting control method allowed more heat into charge and 13% efficiency enhancement; leading to a shorter melting process, less energy consumption and increased melt superheat, which reached 49 °C. The experimental data published in this paper represent a valuable empiric reference for the development and validation of current and future induction heating models.
Open AccessInduction Skull Melting of Ti-6Al-4V: Process Control and Efficiency Optimization
Titanium investment casting is one of the leading and most efficient near-net-shape manufacturing processes, since complex shape components are possible to obtain with a very low amount of material waste. But melting these reactive alloys implies the usage of specific melting technologies such as the Induction Skull Melting (ISM) method. In this work the ISM was extensively studied with the aim of deepening the characteristics of this specific melting method and improving the too low energy efficiency and overall process performance. A 16 segment copper crucible and 3 turns coil was employed for the melting of 1 kg of Ti-6Al-4V alloy. Through the calorimetric balance, real-time evolution of the process parameters and power losses arising from the crucible and coil sub-assemblies was displayed. Results revealed the impact of coil working conditions in the overall ISM thermal efficiency and titanium melt properties, revealing the use of these conditions as an effective optimization strategy. This unstudied melting control method allowed more heat into charge and 13% efficiency enhancement; leading to a shorter melting process, less energy consumption and increased melt superheat, which reached 49 °C. The experimental data published in this paper represent a valuable empiric reference for the development and validation of current and future induction heating models.