Xiaohua Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaohua Liu has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Tianfeng Zhou
State Key Laboratory of Chips and Systems for Advanced Light Field Display, School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China
3 shared publications - Allen Y. Yi
Department of Integrated Systems Engineering, The Ohio State University, Columbus, OH 43210, USA
2 shared publications - Cheng Guo
Guangdong Provincial Key Laboratory of Micro/Nano Optomechatronics Engineering, College of Mechatronics and Control Engineering, Shenzhen University, Shenzhen 518060, China
2 shared publications - Jianfeng Yu
Nanomaterial Innovation Ltd., 1109 Millcreek Lane, Columbus, OH 43220-4949
2 shared publications - Lin Zhang
Department of Integrated Systems Engineering, The Ohio State University, Columbus, OH 43210
2 shared publications - Ly James Lee
Department of Chemical and Biomolecular Engineering, The Ohio State University, Columbus, OH, 43210, USA
2 shared publications
Latest Publications
- Open Access
The Interface Thermal Resistance Evolution between Carbide-Bonded Graphene Coating and Polymer in Rapid Molding for Microlens Array
Surface rapid heating process is an efficient and green method for large-volume production of polymer optics by adopting 3D graphene network coated silicon molds with high thermal conductivity. Nevertheless, the heat transfer mechanism including the interface thermal resistance evolution between 3D graphene network coating and polymer has not been thoroughly revealed. In this study, the interface thermal resistance model was established by simplifying the contact situation between the coating and polymethylmethacrylate (PMMA), and then embedding into the finite element method (FEM) model to study the temperature variations of PMMA in surface rapid heating process. Heating experiments for graphene network were then carried out under different currents to provide the initial heat for heat transfer model. In addition, residual stress of the PMMA lens undergoing the non-uniform thermal history during molding was presented by the simulation model together. Finally, the optimal molding parameters including heating time and pressure will be determined according to calculation results of the interface thermal resistance model and microlens array molding experiment was conducted to illustrate that the interface thermal resistance model can predict the temperature of the polymer to achieve a better filling of microlens array with smooth surface and satisfactory optical performance.
Open AccessThe Interface Thermal Resistance Evolution between Carbide-Bonded Graphene Coating and Polymer in Rapid Molding for Microlens Array
Surface rapid heating process is an efficient and green method for large-volume production of polymer optics by adopting 3D graphene network coated silicon molds with high thermal conductivity. Nevertheless, the heat transfer mechanism including the interface thermal resistance evolution between 3D graphene network coating and polymer has not been thoroughly revealed. In this study, the interface thermal resistance model was established by simplifying the contact situation between the coating and polymethylmethacrylate (PMMA), and then embedding into the finite element method (FEM) model to study the temperature variations of PMMA in surface rapid heating process. Heating experiments for graphene network were then carried out under different currents to provide the initial heat for heat transfer model. In addition, residual stress of the PMMA lens undergoing the non-uniform thermal history during molding was presented by the simulation model together. Finally, the optimal molding parameters including heating time and pressure will be determined according to calculation results of the interface thermal resistance model and microlens array molding experiment was conducted to illustrate that the interface thermal resistance model can predict the temperature of the polymer to achieve a better filling of microlens array with smooth surface and satisfactory optical performance.
- Open Access
Surface Finishing of FDM-Fabricated Amorphous Polyetheretherketone and Its Carbon-Fiber-Reinforced Composite by Dry Milling
In recent years, many investigations have been devoted to fused deposition modeling (FDM) of high-performance polymer-polyetheretherketone (PEEK) and carbon-fiber-reinforced PEEK (CF/PEEK) for biomedical and aerospace applications. However, the staircase effect naturally brought about by FDM restricts further applications of 3D-printed PEEK and its composites in high-temperature molds, medical implants, and precision components, which require better or customized surface qualities. Hence, this work aimed to reduce the staircase effect and improve the surface quality of 3D-printed PEEK and CF/PEEK parts by dry milling of the fluctuant exterior surface. The co-dependency between 3D printing parameters (raster angle and layer thickness) and milling parameters (depth of cut, spindle speed, and feed rate per tooth) were investigated through experiments. The difference in removal mechanisms for PEEK and CF/PEEK was revealed. It was confirmed that the smearing effect enhanced the surface quality based on the morphology analysis and the simulation model. Both the raster angle of +45°/−45° and the small layer thickness could improve the surface quality of these 3D-printed polymers after dry milling. A large depth of cut and a large feed rate per tooth were likely to deteriorate the finished polymer surface. The spindle speed could influence the morphologies without significant changes in roughness values. Finally, a demonstration was performed to verify that dry milling of 3D-printed amorphous PEEK and CF/PEEK parts could lead to a high surface quality for critical requirements.
Open AccessSurface Finishing of FDM-Fabricated Amorphous Polyetheretherketone and Its Carbon-Fiber-Reinforced Composite by Dry Milling
In recent years, many investigations have been devoted to fused deposition modeling (FDM) of high-performance polymer-polyetheretherketone (PEEK) and carbon-fiber-reinforced PEEK (CF/PEEK) for biomedical and aerospace applications. However, the staircase effect naturally brought about by FDM restricts further applications of 3D-printed PEEK and its composites in high-temperature molds, medical implants, and precision components, which require better or customized surface qualities. Hence, this work aimed to reduce the staircase effect and improve the surface quality of 3D-printed PEEK and CF/PEEK parts by dry milling of the fluctuant exterior surface. The co-dependency between 3D printing parameters (raster angle and layer thickness) and milling parameters (depth of cut, spindle speed, and feed rate per tooth) were investigated through experiments. The difference in removal mechanisms for PEEK and CF/PEEK was revealed. It was confirmed that the smearing effect enhanced the surface quality based on the morphology analysis and the simulation model. Both the raster angle of +45°/−45° and the small layer thickness could improve the surface quality of these 3D-printed polymers after dry milling. A large depth of cut and a large feed rate per tooth were likely to deteriorate the finished polymer surface. The spindle speed could influence the morphologies without significant changes in roughness values. Finally, a demonstration was performed to verify that dry milling of 3D-printed amorphous PEEK and CF/PEEK parts could lead to a high surface quality for critical requirements.
- 21 June 2019
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 141 (8)
Fabrication of Plano-Concave Plastic Lens by Novel Injection Molding Using Carbide-Bonded Graphene-Coated Silica Molds
Injection molding of plastic optical lenses prevails over many other techniques in both efficiency and cost; however, polymer shrinkage during cooling, high level of uneven residual stresses, and refractive index variations have limited its potential use for high precision lens fabrication. In this research, we adopted a newly developed strong graphene network to both plano and convex fused silica mold surfaces and proposed a novel injection molding with graphene-coated fused silica molds. This advanced injection molding process was implemented in the molding of polymer-based plano-concave lenses resulting in reduced polymer shrinkage. In addition, internal residual stresses and refractive index variations were also analyzed and discussed in detail. Meanwhile, as a comparison of conventional injection mold material, aluminum mold inserts with the same shape and size were also diamond machined and then employed to mold the same plano-concave lenses. Finally, a simulation model using moldex3d was utilized to interpret stress distributions of both graphene and aluminum molds and then validated by experiments. The comparison between graphene-coated mold and aluminum mold reveals that the novel injection molding with carbide-bonded graphene-coated fused silica mold inserts is capable of molding high-quality optical lenses with much less shrinkage and residual stresses with a more uniform refractive index distribution.
- 21 June 2019
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 141 (8)
Fabrication of Plano-Concave Plastic Lens by Novel Injection Molding Using Carbide-Bonded Graphene-Coated Silica Molds
Injection molding of plastic optical lenses prevails over many other techniques in both efficiency and cost; however, polymer shrinkage during cooling, high level of uneven residual stresses, and refractive index variations have limited its potential use for high precision lens fabrication. In this research, we adopted a newly developed strong graphene network to both plano and convex fused silica mold surfaces and proposed a novel injection molding with graphene-coated fused silica molds. This advanced injection molding process was implemented in the molding of polymer-based plano-concave lenses resulting in reduced polymer shrinkage. In addition, internal residual stresses and refractive index variations were also analyzed and discussed in detail. Meanwhile, as a comparison of conventional injection mold material, aluminum mold inserts with the same shape and size were also diamond machined and then employed to mold the same plano-concave lenses. Finally, a simulation model using moldex3d was utilized to interpret stress distributions of both graphene and aluminum molds and then validated by experiments. The comparison between graphene-coated mold and aluminum mold reveals that the novel injection molding with carbide-bonded graphene-coated fused silica mold inserts is capable of molding high-quality optical lenses with much less shrinkage and residual stresses with a more uniform refractive index distribution.
- Open Access
- 2 July 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (7) , 337
A Review of the Precision Glass Molding of Chalcogenide Glass (ChG) for Infrared Optics
Chalcogenide glass (ChG) is increasingly demanded in infrared optical systems owing to its excellent infrared optical properties. ChG infrared optics including ChG aspherical and freeform optics are mainly fabricated using the single point diamond turning (SPDT) technique, which is characterized by high cost and low efficiency. This paper presents an overview of the ChG infrared optics fabrication technique through precision glass molding (PGM). It introduces the thermo-mechanical properties of ChG and models the elastic-viscoplasticity constitutive of ChG. The forming accuracy and surface defects of the formed ChG are discussed, and the countermeasures to improve the optics quality are also reviewed. Moreover, the latest advancements in ChG precision molding are detailed, including the aspherical lens molding process, the ChG freeform optics molding process, and some new improvements in PGM.
- 2 July 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (7) , 337
Open AccessA Review of the Precision Glass Molding of Chalcogenide Glass (ChG) for Infrared Optics
Chalcogenide glass (ChG) is increasingly demanded in infrared optical systems owing to its excellent infrared optical properties. ChG infrared optics including ChG aspherical and freeform optics are mainly fabricated using the single point diamond turning (SPDT) technique, which is characterized by high cost and low efficiency. This paper presents an overview of the ChG infrared optics fabrication technique through precision glass molding (PGM). It introduces the thermo-mechanical properties of ChG and models the elastic-viscoplasticity constitutive of ChG. The forming accuracy and surface defects of the formed ChG are discussed, and the countermeasures to improve the optics quality are also reviewed. Moreover, the latest advancements in ChG precision molding are detailed, including the aspherical lens molding process, the ChG freeform optics molding process, and some new improvements in PGM.
- 3 November 2017
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (1)
Simulation and Measurement of Refractive Index Variation in Localized Rapid Heating Molding for Polymer Optics
Localized rapid heating process utilizing carbide-bonded graphene-coated silicon molds is a high-efficiency and energy-saving technique for high-volume fabrication of polymer optics. The graphene coating is used as a rapid heating element because of its high thermal conductivity and low electrical resistivity. However, the optical property of molded polymer and its dependence on process conditions such as heat transfer have not been thoroughly investigated. In this research, finite element method (FEM) simulation was utilized to interpret temperature changes of the graphene coating and heat transfer between graphene and polymethylmethacrylate (PMMA) in localized rapid heating. Experiments were then carried out under different voltages to validate the numerical model. In addition, refractive index variation of the PMMA lens resulting from nonuniform thermal history in molding was demonstrated by simulation modeling as well. Finally, wavefront variation of a PMMA lens molded by localized rapid heating was first studied using an FEM model and then verified by optical measurements with a Shack–Hartmann wavefront sensor (SHWFS). The wavefront variation in a PMMA lens molded by conventional method was also measured. Compared with conventional molding process, localized rapid heating is shown to be a possible alternative for better optical performance with a much shorter cycle time.
- 3 November 2017
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (1)
Simulation and Measurement of Refractive Index Variation in Localized Rapid Heating Molding for Polymer Optics
Localized rapid heating process utilizing carbide-bonded graphene-coated silicon molds is a high-efficiency and energy-saving technique for high-volume fabrication of polymer optics. The graphene coating is used as a rapid heating element because of its high thermal conductivity and low electrical resistivity. However, the optical property of molded polymer and its dependence on process conditions such as heat transfer have not been thoroughly investigated. In this research, finite element method (FEM) simulation was utilized to interpret temperature changes of the graphene coating and heat transfer between graphene and polymethylmethacrylate (PMMA) in localized rapid heating. Experiments were then carried out under different voltages to validate the numerical model. In addition, refractive index variation of the PMMA lens resulting from nonuniform thermal history in molding was demonstrated by simulation modeling as well. Finally, wavefront variation of a PMMA lens molded by localized rapid heating was first studied using an FEM model and then verified by optical measurements with a Shack–Hartmann wavefront sensor (SHWFS). The wavefront variation in a PMMA lens molded by conventional method was also measured. Compared with conventional molding process, localized rapid heating is shown to be a possible alternative for better optical performance with a much shorter cycle time.