Kuan-Lin Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kuan-Lin Lee has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Lung-Chien Chen
National Taipei University of Technology
4 shared publications - Ching-Ho Tien
Department of Electro-Optical Engineering, National Taipei University of Technology, Taipei, Taiwan
2 shared publications - Chzu-Chiang Tseng
Department of Electronic Engineering, Institute of Electro-Optical Engineering, Chang Gung University, Chang Gung Memorial Hospital, Taoyuan 333, Taiwan
2 shared publications - Gwomei Wu
Institute of Electro-Optical Engineering, Chang Gung University, Chang Gung Memorial Hospital, Taoyuan 333, Taiwan
2 shared publications - Liann-Be Chang
Department of Electronic Engineering, Chang Gung University, Taoyuan 333, Taiwan
2 shared publications - Ming-Jer Jeng
Department of Electronic Engineering, Chang Gung University, Taoyuan 333, Taiwan
2 shared publications
Latest Publications
- Open Access
Two-Dimensional (PEA)2PbBr4 Perovskites Sensors for Highly Sensitive Ethanol Vapor Detection
Two-dimensional (2D) perovskite have been widely researched for solar cells, light-emitting diodes, photodetectors because of their excellent environmental stability and optoelectronic properties in comparison to three-dimensional (3D) perovskite. In this study, we demonstrate the high response of 2D-(PEA)2PbBr4 perovskite of the horizontal vapor sensor was outstandingly more superior than 3D-MAPbBr3 perovskite. 2D transverse perovskite layer have the large surface-to-volume ratio and reactive surface, with the charge transfer mechanism, which was suitable for vapor sensing and trapping. Thus, 2D perovskite vapor sensors demonstrate the champion current response ratio R of 107.32 under the ethanol vapors, which was much faster than 3D perovskite (R = 2.92).
Open AccessTwo-Dimensional (PEA)2PbBr4 Perovskites Sensors for Highly Sensitive Ethanol Vapor Detection
Two-dimensional (2D) perovskite have been widely researched for solar cells, light-emitting diodes, photodetectors because of their excellent environmental stability and optoelectronic properties in comparison to three-dimensional (3D) perovskite. In this study, we demonstrate the high response of 2D-(PEA)2PbBr4 perovskite of the horizontal vapor sensor was outstandingly more superior than 3D-MAPbBr3 perovskite. 2D transverse perovskite layer have the large surface-to-volume ratio and reactive surface, with the charge transfer mechanism, which was suitable for vapor sensing and trapping. Thus, 2D perovskite vapor sensors demonstrate the champion current response ratio R of 107.32 under the ethanol vapors, which was much faster than 3D perovskite (R = 2.92).
- Open Access
The Effects of Temperature on the Growth of a Lead-Free Perovskite-Like (CH3NH3)3Sb2Br9 Single Crystal for An MSM Photodetector Application
We have fabricated a photodetector based on (CH3NH3)3Sb2Br9 (MA3Sb2Br9) lead-free perovskite-like single crystal, which plays an important role in the optoelectronic characteristics of the photodetector as a perovskite-like photosensitive layer. Here, MA3Sb2Br9 single crystals were synthesized by an inverse temperature crystallization process with a precursor solution at three different growth temperatures, 60 °C, 80 °C, and 100 °C. As a result, a MA3Sb2Br9 single crystal with an optimum growth temperature of 60 °C presented a low trap density of 2.63 × 1011 cm−3, a high charge carrier mobility of 0.75 cm2 V−1 s−1, and excellent crystal structure and optical absorption properties. This MA3Sb2Br9 perovskite-like photodetector displayed a low dark current of 8.09 × 10−9 A, high responsivity of 0.113 A W−1, and high detectivity of 4.32 × 1011 Jones.
Open AccessThe Effects of Temperature on the Growth of a Lead-Free Perovskite-Like (CH3NH3)3Sb2Br9 Single Crystal for An MSM Photodetector Application
We have fabricated a photodetector based on (CH3NH3)3Sb2Br9 (MA3Sb2Br9) lead-free perovskite-like single crystal, which plays an important role in the optoelectronic characteristics of the photodetector as a perovskite-like photosensitive layer. Here, MA3Sb2Br9 single crystals were synthesized by an inverse temperature crystallization process with a precursor solution at three different growth temperatures, 60 °C, 80 °C, and 100 °C. As a result, a MA3Sb2Br9 single crystal with an optimum growth temperature of 60 °C presented a low trap density of 2.63 × 1011 cm−3, a high charge carrier mobility of 0.75 cm2 V−1 s−1, and excellent crystal structure and optical absorption properties. This MA3Sb2Br9 perovskite-like photodetector displayed a low dark current of 8.09 × 10−9 A, high responsivity of 0.113 A W−1, and high detectivity of 4.32 × 1011 Jones.
- Open Access
- 13 March 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (3) , 521
Effects of Annealing on Characteristics of Cu2ZnSnSe4/CH3NH3PbI3/ZnS/IZO Nanostructures for Enhanced Photovoltaic Solar Cells
This paper presents new photovoltaic solar cells with Cu2ZnSnSe4/CH3NH3PbI3(MAPbI3)/ZnS/IZO/Ag nanostructures on bi-layer Mo/FTO (fluorine-doped tin oxide) glasssubstrates. The hole-transporting layer, active absorber layer, electron-transporting layer, transparent-conductive oxide layer, and top electrode-metal contact layer, were made of Cu2ZnSnSe4, MAPbI3 perovskite, zincsulfide, indium-doped zinc oxide, and silver, respectively. The active absorber MAPbI3 perovskite film was deposited on Cu2ZnSnSe4 hole-transporting layer that has been annealed at different temperatures. TheseCu2ZnSnSe4 filmsexhibitedthe morphology with increased crystal grain sizesand reduced pinholes, following the increased annealing temperature. When the perovskitefilm thickness was designed at 700 nm, the Cu2ZnSnSe4 hole-transporting layer was 160 nm, and the IZO (indium-zinc oxide) at 100 nm, and annealed at 650 °C, the experimental results showed significant improvements in the solar cell characteristics. The open-circuit voltage was increased to 1.1 V, the short-circuit current was improved to 20.8 mA/cm2, and the device fill factor was elevated to 76.3%. In addition, the device power-conversion efficiency has been improved to 17.4%. The output power Pmax was as good as 1.74 mW and the device series-resistance was 17.1 Ω.
- 13 March 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (3) , 521
Open AccessEffects of Annealing on Characteristics of Cu2ZnSnSe4/CH3NH3PbI3/ZnS/IZO Nanostructures for Enhanced Photovoltaic Solar Cells
This paper presents new photovoltaic solar cells with Cu2ZnSnSe4/CH3NH3PbI3(MAPbI3)/ZnS/IZO/Ag nanostructures on bi-layer Mo/FTO (fluorine-doped tin oxide) glasssubstrates. The hole-transporting layer, active absorber layer, electron-transporting layer, transparent-conductive oxide layer, and top electrode-metal contact layer, were made of Cu2ZnSnSe4, MAPbI3 perovskite, zincsulfide, indium-doped zinc oxide, and silver, respectively. The active absorber MAPbI3 perovskite film was deposited on Cu2ZnSnSe4 hole-transporting layer that has been annealed at different temperatures. TheseCu2ZnSnSe4 filmsexhibitedthe morphology with increased crystal grain sizesand reduced pinholes, following the increased annealing temperature. When the perovskitefilm thickness was designed at 700 nm, the Cu2ZnSnSe4 hole-transporting layer was 160 nm, and the IZO (indium-zinc oxide) at 100 nm, and annealed at 650 °C, the experimental results showed significant improvements in the solar cell characteristics. The open-circuit voltage was increased to 1.1 V, the short-circuit current was improved to 20.8 mA/cm2, and the device fill factor was elevated to 76.3%. In addition, the device power-conversion efficiency has been improved to 17.4%. The output power Pmax was as good as 1.74 mW and the device series-resistance was 17.1 Ω.
- Open Access
- 19 February 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (4) , 719
Low-Cost CuIn1−xGaxSe2 Ultra-Thin Hole-Transporting Material Layer for Perovskite/CIGSe Heterojunction Solar Cells
This paper presents a new type of solar cellwith enhanced optical-current characteristics using an ultra-thin CuIn1−xGaxSe2 hole-transporting material (HTM) layer (3NH3PbI3 (MAPbI3) perovskite active absorbing material. It promoted carrier transportand led to an improved device with good ohmic-contacts. The solar cell was prepared as a bi-layer Mo/CuIn1−xGaxSe2/perovskite/C60/Ag multilayer of nano-structures on an FTO (fluorine-doped tin oxide) glass substrate. The ultra-thin CuIn1−xGaxSe2 HTM layers were annealed at various temperatures of 400, 500, and 600 °C. Scanning electron microscopy studies revealed that the nano-crystal grain size of CuIn1−xGaxSe2 increased with the annealing temperature. The solar cell results show an improved optical power conversion efficiency at ~14.2%. The application of the CuIn1−xGaxSe2 layer with the perovskite absorbing material could be used for designing solar cells with a reduced HTM thickness. The CuIn1−xGaxSe2 HTM has been evidenced to maintain a properopen circuit voltage, short-circuit current density and photovoltaic stability.
- 19 February 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (4) , 719
Open AccessLow-Cost CuIn1−xGaxSe2 Ultra-Thin Hole-Transporting Material Layer for Perovskite/CIGSe Heterojunction Solar Cells
This paper presents a new type of solar cellwith enhanced optical-current characteristics using an ultra-thin CuIn1−xGaxSe2 hole-transporting material (HTM) layer (3NH3PbI3 (MAPbI3) perovskite active absorbing material. It promoted carrier transportand led to an improved device with good ohmic-contacts. The solar cell was prepared as a bi-layer Mo/CuIn1−xGaxSe2/perovskite/C60/Ag multilayer of nano-structures on an FTO (fluorine-doped tin oxide) glass substrate. The ultra-thin CuIn1−xGaxSe2 HTM layers were annealed at various temperatures of 400, 500, and 600 °C. Scanning electron microscopy studies revealed that the nano-crystal grain size of CuIn1−xGaxSe2 increased with the annealing temperature. The solar cell results show an improved optical power conversion efficiency at ~14.2%. The application of the CuIn1−xGaxSe2 layer with the perovskite absorbing material could be used for designing solar cells with a reduced HTM thickness. The CuIn1−xGaxSe2 HTM has been evidenced to maintain a properopen circuit voltage, short-circuit current density and photovoltaic stability.