Zhimin Liang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhimin Liang has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
Dianlong Wang
4 shared publications- Dianlong Wang
Hebei Key Laboratory of Material Near-Net Forming Technology, School of Materials Science and Engineering, Hebei University of Science and Technology, Shijiazhuang 050018, China
4 shared publications - Liwei Wang
Research Institute of Petroleum Exploration and Development, Beijing 100083, China
4 shared publications - Congwei Cai
School of Materials Science and Engineering, Hebei University of Science and Technology , No. 26 Yuxiang Avenue, Yuhua District , Shijiazhuang 050018 , China
3 shared publications - Dianlong Wang
School of Mechanical Engineering, Yanshan University, Qinhuangdao, China
3 shared publications Balaji Narayanaswamy
Deakin Univ, Sch Engn, Waurn Ponds, Vic 3216, Australia
2 shared publications
Latest Publications
- Open Access
- 18 June 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 31, 733-738
Pulsing-induced healing of a surface crack of a nickel-based alloy
- 18 June 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 31, 733-738
Open AccessPulsing-induced healing of a surface crack of a nickel-based alloy
- Open Access
- 1 May 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (5) , 1754-1768
Synergetic deformation mechanisms in an Mg-Zn-Y-Zr alloy with intragranular LPSO structures
- 1 May 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (5) , 1754-1768
Open AccessSynergetic deformation mechanisms in an Mg-Zn-Y-Zr alloy with intragranular LPSO structures
- 4 October 2022
- Published by Elsevier in Microelectronics Reliability
- Vol. 139
Effect of Ag and Cu co-addition on the microstructure and creep properties of Sn-5Sb solder under current stressing
- 4 October 2022
- Published by Elsevier in Microelectronics Reliability
- Vol. 139
Effect of Ag and Cu co-addition on the microstructure and creep properties of Sn-5Sb solder under current stressing
- Open Access
Failure Analysis of a Chromium Plating Layer on a Piston Rod Surface and the Study of Ni-Based Composite Coating with Nb Addition by Laser Cladding
The failure of a chromium plating layer on the surface of a piston rod was analyzed, and an Ni-based alloy mixed with a niobium (Nb) composite coating was investigated by means of stereomicroscopy, metallographic microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), Vickers hardness testing, and wear testing. The results show that penetrating cracks were present in the chromium layer. Subsequently, the corrosion intensified, resulting in the bubbling, cracking, and peeling of the chromium layer. The cladding layer presented a structure morphology of planar crystalline at the bottom, dendritic at the middle, and equiaxial crystalline at the top. The solidification parameters, which were derived from simulation results, confirmed that the ratios between temperature gradient (G) and solidification speed (S) decreased, and the values of the cooling speeds increased from the bottom to the top of the cladding layer. With an increase in Nb content, the structure became gradually refined and uniformly dense. The cladding layer of the Ni-based alloy mixed with Nb was mainly composed of γ-Ni, Cr23C6, Cr7C3, NbC, and Ni3Nb. NbC could be formed in situ and presented itself in four forms: particles, dendrites, polyhedrals, and networks. The microhardness of the coating with 15% added Nb was enhanced to 400 HV0.2, and the wear resistance thereof was 11.14 times higher than the substrate. After the 15% Nb coating had aged for 16 h, the diffraction peak intensities of Cr23C6 and Cr7C3 significantly increased, and the volume fraction of granular NbC increased from 1.67% to 2.54%. The microhardness was enhanced to 580 HV0.2, and the wear resistance thereof was better than that of the chromium plating layer.
Open AccessFailure Analysis of a Chromium Plating Layer on a Piston Rod Surface and the Study of Ni-Based Composite Coating with Nb Addition by Laser Cladding
The failure of a chromium plating layer on the surface of a piston rod was analyzed, and an Ni-based alloy mixed with a niobium (Nb) composite coating was investigated by means of stereomicroscopy, metallographic microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), Vickers hardness testing, and wear testing. The results show that penetrating cracks were present in the chromium layer. Subsequently, the corrosion intensified, resulting in the bubbling, cracking, and peeling of the chromium layer. The cladding layer presented a structure morphology of planar crystalline at the bottom, dendritic at the middle, and equiaxial crystalline at the top. The solidification parameters, which were derived from simulation results, confirmed that the ratios between temperature gradient (G) and solidification speed (S) decreased, and the values of the cooling speeds increased from the bottom to the top of the cladding layer. With an increase in Nb content, the structure became gradually refined and uniformly dense. The cladding layer of the Ni-based alloy mixed with Nb was mainly composed of γ-Ni, Cr23C6, Cr7C3, NbC, and Ni3Nb. NbC could be formed in situ and presented itself in four forms: particles, dendrites, polyhedrals, and networks. The microhardness of the coating with 15% added Nb was enhanced to 400 HV0.2, and the wear resistance thereof was 11.14 times higher than the substrate. After the 15% Nb coating had aged for 16 h, the diffraction peak intensities of Cr23C6 and Cr7C3 significantly increased, and the volume fraction of granular NbC increased from 1.67% to 2.54%. The microhardness was enhanced to 580 HV0.2, and the wear resistance thereof was better than that of the chromium plating layer.
- 31 March 2022
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 841
Rapidly improved tensile strength of 6N01 Al alloy FSW joints by electropulsing and artificial aging treatment
- 31 March 2022
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 841
Rapidly improved tensile strength of 6N01 Al alloy FSW joints by electropulsing and artificial aging treatment
- Open Access
Effects of Isothermal Aging on Interfacial Microstructure and Shear Properties of Sn-4.5Sb-3.5Bi-0.1Ag Soldering with ENIG and ENEPIG Substrates
Sn–Sb system solders and ENIG/ENEPIG surface finish layers are commonly used in electronic products. To illustrate the thermal reliability evaluation of such solder joints, we studied the interfacial microstructure and shear properties of Sn-4.5Sb-3.5Bi-0.1Ag/ENIG and Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG solder joints after aging at 150 °C for 250, 500 and 1000 h. The results show that the intermetallic compound of Sn-4.5Sb-3.5Bi-0.1Ag/ENIG interface was more continuous and uniform compared with that of Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG interface after reflow. The thickness of the interfacial intermetallic compounds of the former was significantly thinner than that of the latter before and after aging. With extension of aging time, the former interface was stable, while obvious voids appeared at the interface of the latter after 500 h aging and significant fracture occurred after 1000 h aging. The shear tests proved that shear strength of solder joints decreased with increasing aging time. For the Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG joint after 1000 h aging, the fracture mode is ductile-brittle mixed type, which means fracture could occur at the solder matrix or the solder/IMC interface. For other samples of these two types of joints, ductile fracture occurred inside of the solder. The Sn-4.5Sb-3.5Bi-0.1Ag/ENIG solder joint was thermally more reliable than Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG.
Open AccessEffects of Isothermal Aging on Interfacial Microstructure and Shear Properties of Sn-4.5Sb-3.5Bi-0.1Ag Soldering with ENIG and ENEPIG Substrates
Sn–Sb system solders and ENIG/ENEPIG surface finish layers are commonly used in electronic products. To illustrate the thermal reliability evaluation of such solder joints, we studied the interfacial microstructure and shear properties of Sn-4.5Sb-3.5Bi-0.1Ag/ENIG and Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG solder joints after aging at 150 °C for 250, 500 and 1000 h. The results show that the intermetallic compound of Sn-4.5Sb-3.5Bi-0.1Ag/ENIG interface was more continuous and uniform compared with that of Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG interface after reflow. The thickness of the interfacial intermetallic compounds of the former was significantly thinner than that of the latter before and after aging. With extension of aging time, the former interface was stable, while obvious voids appeared at the interface of the latter after 500 h aging and significant fracture occurred after 1000 h aging. The shear tests proved that shear strength of solder joints decreased with increasing aging time. For the Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG joint after 1000 h aging, the fracture mode is ductile-brittle mixed type, which means fracture could occur at the solder matrix or the solder/IMC interface. For other samples of these two types of joints, ductile fracture occurred inside of the solder. The Sn-4.5Sb-3.5Bi-0.1Ag/ENIG solder joint was thermally more reliable than Sn-4.5Sb-3.5Bi-0.1Ag/ENEPIG.
- 19 October 2021
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 17 (2) , 1077-1086
A 5.6 kW 11.7 kW per kg Four-Phase Interleaved Buck Converter for the Unmanned Aerial Vehicle
- 19 October 2021
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 17 (2) , 1077-1086
A 5.6 kW 11.7 kW per kg Four-Phase Interleaved Buck Converter for the Unmanned Aerial Vehicle
- 1 October 2021
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 296
Low energy ultrasonic welding for Cu-Cu joining accelerated via Cu nanoparticles
- 1 October 2021
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 296
Low energy ultrasonic welding for Cu-Cu joining accelerated via Cu nanoparticles
- Open Access
- 1 January 2021
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 40 (1) , 214-227
Microstructure and mechanical properties of 2060 Al–Li alloy welded by alternating current cold metal transfer with high-frequency pulse current
Al–Li alloy has been widely used in the aerospace field owing to its high strength and low density. In this study, alternating current cold metal transfer (AC CMT) along with a high-frequency pulse current technique was used to weld a 2060 Al–Li alloy using an ER5356 wire. The effect of pulse frequency on the arc shape, microstructure, and mechanical properties of the welded joints was examined, and mechanical performance testing was conducted. The results revealed that the arc diameter, arc length, and arc volume showed a trend of increasing first and then decreasing with an increase in the pulse frequency and reached their peak values when the pulse frequency was 50 kHz. Coupling the welding process with a high-frequency pulse resulted in grain refinement, which was attributed to the stirring action of the arc force. Both the porosity levels and grain size decreased with increasing frequency. When the pulse frequency was 70 kHz, the porosity level was the lowest, and the grain size was refined to 24.1 μm. The tensile strength of the welded joints also increased with the pulse frequency, and a maximum tensile strength of 249 MPa was observed at 70 kHz.
- 1 January 2021
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 40 (1) , 214-227
Open AccessMicrostructure and mechanical properties of 2060 Al–Li alloy welded by alternating current cold metal transfer with high-frequency pulse current
Al–Li alloy has been widely used in the aerospace field owing to its high strength and low density. In this study, alternating current cold metal transfer (AC CMT) along with a high-frequency pulse current technique was used to weld a 2060 Al–Li alloy using an ER5356 wire. The effect of pulse frequency on the arc shape, microstructure, and mechanical properties of the welded joints was examined, and mechanical performance testing was conducted. The results revealed that the arc diameter, arc length, and arc volume showed a trend of increasing first and then decreasing with an increase in the pulse frequency and reached their peak values when the pulse frequency was 50 kHz. Coupling the welding process with a high-frequency pulse resulted in grain refinement, which was attributed to the stirring action of the arc force. Both the porosity levels and grain size decreased with increasing frequency. When the pulse frequency was 70 kHz, the porosity level was the lowest, and the grain size was refined to 24.1 μm. The tensile strength of the welded joints also increased with the pulse frequency, and a maximum tensile strength of 249 MPa was observed at 70 kHz.
- 8 October 2020
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 35 (9) , 993-1005
Research on the corrosion behavior of double-side friction stir welded 6082Al alloy thick plate
In order to study the influences of microstructures on corrosion behavior of double-side friction stir welded 6082Al thick plate. The corrosion behavior was firstly clarified by potentiodynamic polarization and exfoliation corrosion (EXCO) tests. The microstructures before and after corrosion were identified by optical microscopy (OM), SEM and transmission electron microscope (TEM). The results showed that the corrosion resistance of heat-affected zone (HAZ) and base material (BM) was lower than those of thermo mechanically affected zone (TMAZ), top of NZ and middle of NZ. Bottom part of NZ was the most severe corroded zone. Intergranular corrosion along grain boundaries was the dominant corrosion type in BM, HAZ, TMAZ and bottom of NZ, while the top and middle part of NZ were susceptibility to pitting. The corrosion resistance decreased with the increase of weld pass. The precipitates mainly precipitated in NZ of the first pass and HAZ of both two passes during double side friction stir welding (FSW) due to the over aging process, which deteriorated the corrosion resistance.
- 8 October 2020
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 35 (9) , 993-1005
Research on the corrosion behavior of double-side friction stir welded 6082Al alloy thick plate
In order to study the influences of microstructures on corrosion behavior of double-side friction stir welded 6082Al thick plate. The corrosion behavior was firstly clarified by potentiodynamic polarization and exfoliation corrosion (EXCO) tests. The microstructures before and after corrosion were identified by optical microscopy (OM), SEM and transmission electron microscope (TEM). The results showed that the corrosion resistance of heat-affected zone (HAZ) and base material (BM) was lower than those of thermo mechanically affected zone (TMAZ), top of NZ and middle of NZ. Bottom part of NZ was the most severe corroded zone. Intergranular corrosion along grain boundaries was the dominant corrosion type in BM, HAZ, TMAZ and bottom of NZ, while the top and middle part of NZ were susceptibility to pitting. The corrosion resistance decreased with the increase of weld pass. The precipitates mainly precipitated in NZ of the first pass and HAZ of both two passes during double side friction stir welding (FSW) due to the over aging process, which deteriorated the corrosion resistance.