Jens Neumann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Jens Neumann has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Christian Hasse
Technical University of Darmstadt
8 shared publications - Michael Wensing
Erlangen Graduate School in Advanced Optical Technologies (SAOT), FAU, Erlangen, Germany
4 shared publications Hans Wengle
3 shared publications- Manuel Dorsch
Development Powertrain, BMW Group, Munich, Germany
2 shared publications Sebastian Grasreiner
2 shared publicationsA. Zschutschke
1 shared publication
Latest Publications
- 23 March 2022
- Published by Elsevier in Chemical Engineering Journal
- Vol. 441
A model-based analysis of washcoat distribution on zoned coated gasoline particulate filters
- 23 March 2022
- Published by Elsevier in Chemical Engineering Journal
- Vol. 441
A model-based analysis of washcoat distribution on zoned coated gasoline particulate filters
- Open Access
- 3 January 2020
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 22 (4) , 1166-1179
A phenomenological modelling framework for particle emission simulation in a direct-injection gasoline engine
A phenomenological modelling framework is presented that allows the simulation of the engine-out particle emissions of direct-injection gasoline engines based on physical principles. It is applicable both at steady-state operating conditions and in transient driving cycles. Within the modelling framework, a multi-zone model with gas-phase reaction kinetics is coupled with a stochastic reactor model considering the soot formation dynamics. Both model parts are fed with inputs from an accompanying engine process simulation. Particle emissions from injector deposits and inhomgeneous gaseous mixture preparation are taken into account. Pyrolysis reactions are considered in a zone with remaining fuel film at the injector, whereas in gas-phase zones that arise from inhomogeneous mixture preparation, the reaction of the air–fuel mixture is calculated under sub-stoichiometric conditions. The setup of those mixture-induced zones is generated by an existing homogenisation sub-model. The modelling framework is evaluated by test bench measurements of the engine operating map, a variation of engine actuator settings and transient driving profiles. Hereby, an accuracy of less than 20% deviation for particle number and mass is achieved.
- 3 January 2020
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 22 (4) , 1166-1179
Open AccessA phenomenological modelling framework for particle emission simulation in a direct-injection gasoline engine
A phenomenological modelling framework is presented that allows the simulation of the engine-out particle emissions of direct-injection gasoline engines based on physical principles. It is applicable both at steady-state operating conditions and in transient driving cycles. Within the modelling framework, a multi-zone model with gas-phase reaction kinetics is coupled with a stochastic reactor model considering the soot formation dynamics. Both model parts are fed with inputs from an accompanying engine process simulation. Particle emissions from injector deposits and inhomgeneous gaseous mixture preparation are taken into account. Pyrolysis reactions are considered in a zone with remaining fuel film at the injector, whereas in gas-phase zones that arise from inhomogeneous mixture preparation, the reaction of the air–fuel mixture is calculated under sub-stoichiometric conditions. The setup of those mixture-induced zones is generated by an existing homogenisation sub-model. The modelling framework is evaluated by test bench measurements of the engine operating map, a variation of engine actuator settings and transient driving profiles. Hereby, an accuracy of less than 20% deviation for particle number and mass is achieved.
- 13 July 2019
- Published by Springer Nature in Automotive and Engine Technology
- Vol. 4 (3-4) , 125-137
Fully coupled control of a spark-ignited engine in driving cycle simulations
- 13 July 2019
- Published by Springer Nature in Automotive and Engine Technology
- Vol. 4 (3-4) , 125-137
Fully coupled control of a spark-ignited engine in driving cycle simulations
- 1 July 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 121, 190-199
Model-based virtual engine calibration with the help of phenomenological methods for spark-ignited engines
- 1 July 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 121, 190-199
Model-based virtual engine calibration with the help of phenomenological methods for spark-ignited engines
- 6 June 2017
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 19 (2) , 168-178
A phenomenological mixture homogenization model for spark-ignition direct-injection engines
In modern turbocharged direct-injection, spark-ignition engines, proper calibration of the engine control unit is essential to handle the increasing variability of actuators. The physically based simulation of engine processes such as mixture homogenization enables a model-based calibration of the engine control unit to identify an ideal set of actuator settings, for example, for efficient combustion with reduced exhaust emissions. In this work, a zero-dimensional phenomenological model for direct-injection, spark-ignition engines is presented that allows the equivalence ratio distribution function in the combustion chamber to be calculated and its development is tracked over time. The model considers the engine geometry, mixing time, charge motion and spray–charge interaction. Accompanying three-dimensional computational fluid dynamics, simulations are performed to obtain information on homogeneity at different operating conditions and to calibrate the model. The calibrated model matches the three-dimensional computational fluid dynamics reference both for the temporal homogeneity development and for the equivalence ratio distribution at the ignition time, respectively. When the model is validated outside the calibrated operating conditions, this shows satisfying results in terms of mixture homogeneity at the time of ignition. Additionally, only a slight modification of the calibration is shown to be required when transferring the model to a comparable engine. While the model is primarily aimed at target applications such as a direct-injection, spark-ignition soot emission model, its application to other issues, such as gaseous exhaust emissions, engine knock or cyclic fluctuations, is conceivable due to its general structure. The fast calculation enables mixture inhomogeneities to be estimated during driving cycle simulations.
- 6 June 2017
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 19 (2) , 168-178
A phenomenological mixture homogenization model for spark-ignition direct-injection engines
In modern turbocharged direct-injection, spark-ignition engines, proper calibration of the engine control unit is essential to handle the increasing variability of actuators. The physically based simulation of engine processes such as mixture homogenization enables a model-based calibration of the engine control unit to identify an ideal set of actuator settings, for example, for efficient combustion with reduced exhaust emissions. In this work, a zero-dimensional phenomenological model for direct-injection, spark-ignition engines is presented that allows the equivalence ratio distribution function in the combustion chamber to be calculated and its development is tracked over time. The model considers the engine geometry, mixing time, charge motion and spray–charge interaction. Accompanying three-dimensional computational fluid dynamics, simulations are performed to obtain information on homogeneity at different operating conditions and to calibrate the model. The calibrated model matches the three-dimensional computational fluid dynamics reference both for the temporal homogeneity development and for the equivalence ratio distribution at the ignition time, respectively. When the model is validated outside the calibrated operating conditions, this shows satisfying results in terms of mixture homogeneity at the time of ignition. Additionally, only a slight modification of the calibration is shown to be required when transferring the model to a comparable engine. While the model is primarily aimed at target applications such as a direct-injection, spark-ignition soot emission model, its application to other issues, such as gaseous exhaust emissions, engine knock or cyclic fluctuations, is conceivable due to its general structure. The fast calculation enables mixture inhomogeneities to be estimated during driving cycle simulations.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Powertrains
- Vol. 6 (4) , 323
Mean value engine model for early stage design of powertrains with turbocharged SI engines
Due to complexity and computing time, crank-angle resolved engine simulation does not fit the needs of early stage powertrain development. Therefore, a mean value model is developed to design powertrains with exhaust turbocharged spark ignition engines. As turbocharger size strongly affects the transient engine process, the interaction between turbocharger and internal combustion engine is investigated and a new method is presented to consider different turbocharger sizes within the same set of mean value engine data. To compensate the linearisation error in the mean value turbine, two new equations are derived. The newly introduced turbine factors enable the model to predict the transient engine behaviour. The model is successfully validated against measured data from transient driving manoeuvres and sample applications are given. The developed model offers a speed-up factor of 30-40 compared to a crank-angle resolved engine model and is especially suited when a large quantity of design parameters is varied.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Powertrains
- Vol. 6 (4) , 323
Mean value engine model for early stage design of powertrains with turbocharged SI engines
Due to complexity and computing time, crank-angle resolved engine simulation does not fit the needs of early stage powertrain development. Therefore, a mean value model is developed to design powertrains with exhaust turbocharged spark ignition engines. As turbocharger size strongly affects the transient engine process, the interaction between turbocharger and internal combustion engine is investigated and a new method is presented to consider different turbocharger sizes within the same set of mean value engine data. To compensate the linearisation error in the mean value turbine, two new equations are derived. The newly introduced turbine factors enable the model to predict the transient engine behaviour. The model is successfully validated against measured data from transient driving manoeuvres and sample applications are given. The developed model offers a speed-up factor of 30-40 compared to a crank-angle resolved engine model and is especially suited when a large quantity of design parameters is varied.
- 1 April 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 98, 502-512
Derivation and validation of a heat transfer model in a hydrogen combustion engine
- 1 April 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 98, 502-512
Derivation and validation of a heat transfer model in a hydrogen combustion engine
- 15 October 2015
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 138 (2) , 022201
Application of a Phenomenological Model for the Engine-Out Emissions of Unburned Hydrocarbons in Driving Cycles
In this work, the application of a phenomenological model to determine engine-out hydrocarbon (HC) emissions in driving cycles is presented. The calculation is coupled to a physical-based simulation environment consisting of interacting submodels of engine, vehicle, and engine control. As a novelty, this virtual calibration methodology can be applied to optimize the energy conversion inside a spark-ignited (SI) internal combustion engine at transient operation. Using detailed information about the combustion process, the main origins and formation mechanisms of unburned HCs like piston crevice, oil layer, and wall quenching are considered in the prediction, as well as the in-cylinder postoxidation. Several parameterization approaches, especially, of the oil layer mechanism are discussed. After calibrating the emission model to a steady-state engine map, the transient results are validated successfully against measurements of various driving cycles based on different calibration strategies of engine operation.
- 15 October 2015
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 138 (2) , 022201
Application of a Phenomenological Model for the Engine-Out Emissions of Unburned Hydrocarbons in Driving Cycles
In this work, the application of a phenomenological model to determine engine-out hydrocarbon (HC) emissions in driving cycles is presented. The calculation is coupled to a physical-based simulation environment consisting of interacting submodels of engine, vehicle, and engine control. As a novelty, this virtual calibration methodology can be applied to optimize the energy conversion inside a spark-ignited (SI) internal combustion engine at transient operation. Using detailed information about the combustion process, the main origins and formation mechanisms of unburned HCs like piston crevice, oil layer, and wall quenching are considered in the prediction, as well as the in-cylinder postoxidation. Several parameterization approaches, especially, of the oil layer mechanism are discussed. After calibrating the emission model to a steady-state engine map, the transient results are validated successfully against measurements of various driving cycles based on different calibration strategies of engine operation.
- 1 July 2015
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 137 (7) , 071502
A Quasi-dimensional Model of the Ignition Delay for Combustion Modeling in Spark-Ignition Engines
Quasi-dimensional (QD) modeling of combustion in spark-ignition (SI) engines allows to describe the most relevant processes of heat release. Here, a submodel for the ignition delay is introduced and applied. The start of combustion is considered from ignition to the crank angle of 5% burned gas fraction. The introduced physical approach identifies the turbulent propagation velocity of the initiated kernel by taking into account early flame expansion and geometric restrictions of the flame propagation. The model is applied to stationary operation within an entire engine map of a turbocharged direct injection SI engine with fully variable valvetrain. Based on provided cycle-averaged input data, the model delivers good results within the margins of measured cycle-to-cycle fluctuations. Thus, it contributes to the assessment of the interplay between engine, engine control unit, drivetrain, and vehicle dynamics, hence making a step toward optimization and virtual engine calibration.
- 1 July 2015
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 137 (7) , 071502
A Quasi-dimensional Model of the Ignition Delay for Combustion Modeling in Spark-Ignition Engines
Quasi-dimensional (QD) modeling of combustion in spark-ignition (SI) engines allows to describe the most relevant processes of heat release. Here, a submodel for the ignition delay is introduced and applied. The start of combustion is considered from ignition to the crank angle of 5% burned gas fraction. The introduced physical approach identifies the turbulent propagation velocity of the initiated kernel by taking into account early flame expansion and geometric restrictions of the flame propagation. The model is applied to stationary operation within an entire engine map of a turbocharged direct injection SI engine with fully variable valvetrain. Based on provided cycle-averaged input data, the model delivers good results within the margins of measured cycle-to-cycle fluctuations. Thus, it contributes to the assessment of the interplay between engine, engine control unit, drivetrain, and vehicle dynamics, hence making a step toward optimization and virtual engine calibration.