Kemin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kemin Li has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Yupeng Shen
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi'an, China
2 shared publications - Zhifu Huang
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications Hui Li
Xi'an Jiaotong University, Xi'an, Shaanxi, China
1 shared publication- Lei Zhang
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Lin He
State Key Laboratory for Mechanical Behavior of Materials, Xi'an, CHINA
1 shared publication Qiaoling Zheng
Xi'an Jiaotong University, Xi'an, Shaanxi, China
1 shared publication
Latest Publications
- 25 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106506
Effect of oxidation time on the short time oxidation behavior and tribological performance of bulk Fe2B
The effects of oxidation time on the short time oxidation behavior and tribological performance of bulk Fe2B have been investigated in this present study. The results reveal that oxidation weight gain, average roughness of oxidation surface and oxidation layer thickness increase with oxidation time increases. Micro-bulges appear and grow up gradually on the oxidation surface as the increasing of oxidation time. The oxidation produces consisting of ɑ-Fe, Fe2O3, Fe3O4, FeBO3,Fe2OBO3, B2O3 and H3BO3 are generated on the surface. At a relative speed of 0.075 m/s under a normal load of 8 N, the values of friction coefficient and wear rate go down first, later go up, and then go down again. The lowest friction coefficient and wear rate can be obtained for the sample with a 9 min oxidation treatment before friction.
- 25 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106506
Effect of oxidation time on the short time oxidation behavior and tribological performance of bulk Fe2B
The effects of oxidation time on the short time oxidation behavior and tribological performance of bulk Fe2B have been investigated in this present study. The results reveal that oxidation weight gain, average roughness of oxidation surface and oxidation layer thickness increase with oxidation time increases. Micro-bulges appear and grow up gradually on the oxidation surface as the increasing of oxidation time. The oxidation produces consisting of ɑ-Fe, Fe2O3, Fe3O4, FeBO3,Fe2OBO3, B2O3 and H3BO3 are generated on the surface. At a relative speed of 0.075 m/s under a normal load of 8 N, the values of friction coefficient and wear rate go down first, later go up, and then go down again. The lowest friction coefficient and wear rate can be obtained for the sample with a 9 min oxidation treatment before friction.
- 25 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (7) , 076506
Influence of Cr addition on tribological properties of bulk Fe2B under dry friction and water lubrication
In the present study, friction and wear properties of bulk Fe2B with different Cr additions were examined under dry friction and water lubrication conditions. The morphology, structure, mechanical properties and tribological properties were investigated by OM, SEM, XRD and XPS. The results show that there is no obvious new phase generated and the crystal structure has no changes with Cr addition. Cr element solubilizes in Fe2B gains without any segregation, only bits of (Fe, Cr)2B crystals formed. With the increasing of Cr addition, the fracture toughness increases first then decreases, and 2Cr sample has the highest toughness. Under dry friction condition, the friction coefficient and wear loss are all decrease first and then increase. 2Cr sample has the highest friction coefficient and wear loss. The tribochemical products form a lubricating film to reduce the friction coefficient and wear loss. And the wear mechanism is mainly brittle fracture. Under water lubrication condition, the friction coefficient drops remarkably, then slightly rises up. In contrast, the wear loss increases first and then decreases. 2Cr sample has the lowest friction coefficient, but the highest wear loss. The wear mechanism is mainly tribo-chemical wear in water. A comparison of the results under dry friction and water lubrication conditions, for the same sample, the friction coefficient is lower, but the wear loss is higher in water.
- 25 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (7) , 076506
Influence of Cr addition on tribological properties of bulk Fe2B under dry friction and water lubrication
In the present study, friction and wear properties of bulk Fe2B with different Cr additions were examined under dry friction and water lubrication conditions. The morphology, structure, mechanical properties and tribological properties were investigated by OM, SEM, XRD and XPS. The results show that there is no obvious new phase generated and the crystal structure has no changes with Cr addition. Cr element solubilizes in Fe2B gains without any segregation, only bits of (Fe, Cr)2B crystals formed. With the increasing of Cr addition, the fracture toughness increases first then decreases, and 2Cr sample has the highest toughness. Under dry friction condition, the friction coefficient and wear loss are all decrease first and then increase. 2Cr sample has the highest friction coefficient and wear loss. The tribochemical products form a lubricating film to reduce the friction coefficient and wear loss. And the wear mechanism is mainly brittle fracture. Under water lubrication condition, the friction coefficient drops remarkably, then slightly rises up. In contrast, the wear loss increases first and then decreases. 2Cr sample has the lowest friction coefficient, but the highest wear loss. The wear mechanism is mainly tribo-chemical wear in water. A comparison of the results under dry friction and water lubrication conditions, for the same sample, the friction coefficient is lower, but the wear loss is higher in water.