Norbert Kępczak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Norbert Kępczak has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Witold Pawłowski
Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Lodz, Poland
11 shared publications - Grzegorz Bechciński
Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Lodz, Poland
6 shared publications - Radosław Rosik
Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Lodz, Poland
6 shared publications - Małgorzata Sikora
Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Lodz, Poland
5 shared publications - Wojciech Stachurski
Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Lodz, Poland
4 shared publications Radosław Rosik
Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology , Stefanowskiego 1/15 , 90-537 Lodz , Poland
3 shared publications
Latest Publications
- Open Access
Influence of Machining Parameters on the Surface Roughness and Tool Wear During Slot Milling of a Polyurethane Block
The aim of the work was to investigate the influence of the machining parameters on the surface roughness and tool wear during slot milling of a polyurethane block (PUB). In the experiment, the influence of the cutting speed, the feed per tooth and the depth of cut on the roughness Ra and Rz of the milling slot surface and wear of the end mill was analyzed. A three-axis CNC milling machine Emco Concept Mill 55 was used to perform the study. After the machining, the values of parameters Ra and Rz were measured using the Hommel Tester T500 induction profilometer. Three polyurethane materials of different densities were considered: the Labelite 45, the Prolab 65 and the LAB 1000. The wear of the end mill was also examined for each of the tested materials by a workshop microscope. In conclusion, it was indicated how and to what extent the variation in the machining parameters affects the surface geometrical structure of a polyurethane plate. Moreover, the research results for the tested materials were compared with each other.
Open AccessInfluence of Machining Parameters on the Surface Roughness and Tool Wear During Slot Milling of a Polyurethane Block
The aim of the work was to investigate the influence of the machining parameters on the surface roughness and tool wear during slot milling of a polyurethane block (PUB). In the experiment, the influence of the cutting speed, the feed per tooth and the depth of cut on the roughness Ra and Rz of the milling slot surface and wear of the end mill was analyzed. A three-axis CNC milling machine Emco Concept Mill 55 was used to perform the study. After the machining, the values of parameters Ra and Rz were measured using the Hommel Tester T500 induction profilometer. Three polyurethane materials of different densities were considered: the Labelite 45, the Prolab 65 and the LAB 1000. The wear of the end mill was also examined for each of the tested materials by a workshop microscope. In conclusion, it was indicated how and to what extent the variation in the machining parameters affects the surface geometrical structure of a polyurethane plate. Moreover, the research results for the tested materials were compared with each other.
- Open Access
Mathematical Models of Grinding Forces in the Hob Cutter Sharpening Process
The article presents the results of research aimed at developing mathematical models for determining the components of grinding force occurring during the sharpening of the rake face of hob cutters. The development of the models was based on the results obtained during experimental tests conducted in the first stage of the research. The studies were carried out using a tool grinder and an aluminum oxide grinding wheel. During the tests, two components of the grinding force were measured, using a piezoelectric dynamometer. A sample made of HS6-5-2 high-speed steel was ground. Grinding was carried out using different sets of cutting parameters. Based on the obtained measurement results, two mathematical models were developed in the form of (1) a multiple regression function and (2) a polynomial function, enabling the calculation of the normal and the tangential force. The experimentally obtained results were then compared with those calculated based on the developed models, and the results of this comparison showed that the developed models provide a good basis for analyzing the sharpening process of hob cutters in terms of variable grinding parameters.
Open AccessMathematical Models of Grinding Forces in the Hob Cutter Sharpening Process
The article presents the results of research aimed at developing mathematical models for determining the components of grinding force occurring during the sharpening of the rake face of hob cutters. The development of the models was based on the results obtained during experimental tests conducted in the first stage of the research. The studies were carried out using a tool grinder and an aluminum oxide grinding wheel. During the tests, two components of the grinding force were measured, using a piezoelectric dynamometer. A sample made of HS6-5-2 high-speed steel was ground. Grinding was carried out using different sets of cutting parameters. Based on the obtained measurement results, two mathematical models were developed in the form of (1) a multiple regression function and (2) a polynomial function, enabling the calculation of the normal and the tangential force. The experimentally obtained results were then compared with those calculated based on the developed models, and the results of this comparison showed that the developed models provide a good basis for analyzing the sharpening process of hob cutters in terms of variable grinding parameters.
- Open Access
Operating Properties of Deep Hole Boring Tools with Modified Design
This paper presents the results of research work on the revised design of a deep hole boring tool. The study was divided into three stages: theoretical, experimental and operational. In the theoretical part, a 3D model of the actual boring bar was created, which was subjected to strength tests using the Finite Element Method (FEM), and then prototypes of new deep hole boring tools were made with structural modifications to the shank part of the tool. For the polymer concrete core of a shank, there was a 14.59% lower displacement, and for the rubber-doped polymer concrete (SBR—styrene butadiene rubber) core of a shank there was a 4.84% lower displacement in comparison to the original boring bar. In the experimental part of the study, the original boring bar and the prototypes were subjected to experimental modal analysis and static analysis tests to compare dynamic and static properties. In the operational part of the study, boring tests were carried out for various workpiece materials, during which the basic parameters of the surface geometric structure (SGS), such as roughness Ra and Rz, were studied. Despite the promising preliminary results of the theoretical and experimental studies, using the described modifications to the boring bar is not recommended.
Open AccessOperating Properties of Deep Hole Boring Tools with Modified Design
This paper presents the results of research work on the revised design of a deep hole boring tool. The study was divided into three stages: theoretical, experimental and operational. In the theoretical part, a 3D model of the actual boring bar was created, which was subjected to strength tests using the Finite Element Method (FEM), and then prototypes of new deep hole boring tools were made with structural modifications to the shank part of the tool. For the polymer concrete core of a shank, there was a 14.59% lower displacement, and for the rubber-doped polymer concrete (SBR—styrene butadiene rubber) core of a shank there was a 4.84% lower displacement in comparison to the original boring bar. In the experimental part of the study, the original boring bar and the prototypes were subjected to experimental modal analysis and static analysis tests to compare dynamic and static properties. In the operational part of the study, boring tests were carried out for various workpiece materials, during which the basic parameters of the surface geometric structure (SGS), such as roughness Ra and Rz, were studied. Despite the promising preliminary results of the theoretical and experimental studies, using the described modifications to the boring bar is not recommended.
- Open Access
Oblique Vibratory Surface Grinding—Experimental Study
The article reports the results of experimental study of vibratory surface grinding in the range of low excitation frequencies and variable directions of excited vibrations in the plane of the table, and investigates the effect of these directions on the roughness and waviness of the ground surface. The tests were conducted on a production surface grinder with a vibrating table on which the samples were mounted. The table made it possible to change the direction for the introduction of vibrations to the workpiece (longitudinally, transversely, and obliquely to the longitudinal feed of the table) and the parameters of the introduced vibrations, frequency and amplitude. In the course of the study, selected parameters of surface roughness and waviness of samples ground conventionally and with vibrations introduced on the workpiece were compared. The results show an improvement in the roughness and waviness parameters of the vibration-ground surfaces compared to surfaces ground without vibration (conventionally). The profile of the ground surface was subjected to Fourier analysis and the harmonic components of the surface shape of the ground samples were determined to characterize the effect of the introduced vibrations on the surface roughness. It was determined that the direction of vibration introduction, which is most favorable in terms of the parameters of the geometric structure of the ground surface, is the direction perpendicular to the longitudinal feed of the grinding table. In other directions of vibration introduction, the simultaneous effect of improving both parameters of the geometric structure of the ground surface profile was not obtained.
Open AccessOblique Vibratory Surface Grinding—Experimental Study
The article reports the results of experimental study of vibratory surface grinding in the range of low excitation frequencies and variable directions of excited vibrations in the plane of the table, and investigates the effect of these directions on the roughness and waviness of the ground surface. The tests were conducted on a production surface grinder with a vibrating table on which the samples were mounted. The table made it possible to change the direction for the introduction of vibrations to the workpiece (longitudinally, transversely, and obliquely to the longitudinal feed of the table) and the parameters of the introduced vibrations, frequency and amplitude. In the course of the study, selected parameters of surface roughness and waviness of samples ground conventionally and with vibrations introduced on the workpiece were compared. The results show an improvement in the roughness and waviness parameters of the vibration-ground surfaces compared to surfaces ground without vibration (conventionally). The profile of the ground surface was subjected to Fourier analysis and the harmonic components of the surface shape of the ground samples were determined to characterize the effect of the introduced vibrations on the surface roughness. It was determined that the direction of vibration introduction, which is most favorable in terms of the parameters of the geometric structure of the ground surface, is the direction perpendicular to the longitudinal feed of the grinding table. In other directions of vibration introduction, the simultaneous effect of improving both parameters of the geometric structure of the ground surface profile was not obtained.
- 6 July 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 144 (1) , 1-36
Experimental Oscillation-Assisted Cylindrical Plunge Grinding
The paper presents experimental studies of the influence of amplitude, frequency, time of oscillation, and average value of the rotational speed of the workpiece on the waviness of the ground surface during cylindrical outer diameter plunge grinding on a mass-produced cylindrical grinder. Oscillations were introduced in order to counteract the development of self-excited vibrations during spark-out. The waviness of the surface was determined by a laser distance measurement system. The results of the experiments indicate the important positive influence of the oscillations applied during spark-out on the waviness of the ground surface. The conclusions of the study regarding the process as well as the technology of cylindrical plunge grinding are presented.
- 6 July 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 144 (1) , 1-36
Experimental Oscillation-Assisted Cylindrical Plunge Grinding
The paper presents experimental studies of the influence of amplitude, frequency, time of oscillation, and average value of the rotational speed of the workpiece on the waviness of the ground surface during cylindrical outer diameter plunge grinding on a mass-produced cylindrical grinder. Oscillations were introduced in order to counteract the development of self-excited vibrations during spark-out. The waviness of the surface was determined by a laser distance measurement system. The results of the experiments indicate the important positive influence of the oscillations applied during spark-out on the waviness of the ground surface. The conclusions of the study regarding the process as well as the technology of cylindrical plunge grinding are presented.
- 2 January 2021
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 23 (1) , 55-62
Experimental verification of the deep hole boring bar model
The article presents the results of the experimental verification of the deep hole boring bar tool model. The aim of the work was to obtain a verified boring bar tool model, which in further scientific research will be a starting point for creating a prototype of a tool with a new design, in which dynamic properties will be improved. The research was divided into two stages. In the first stage, modal studies of the model and the real object were carried out. The obtained discrepancy between numerical and experimental results below 8% allows to state that the model is characterized by dynamic properties occurring in the real boring bar. In the second stage of the research, static tests were carried out. The object was loaded with forces of 98.6 N, 195.0 N, 293.8 N. The obtained slight discrepancy in the results of numerical and experimental tests below 3% allows to state that the model reflects the static properties of the real boring bar. The high convergence of the theoretical and experimental results allows for the conclusion that the numerical model has been verified positively.
- 2 January 2021
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 23 (1) , 55-62
Experimental verification of the deep hole boring bar model
The article presents the results of the experimental verification of the deep hole boring bar tool model. The aim of the work was to obtain a verified boring bar tool model, which in further scientific research will be a starting point for creating a prototype of a tool with a new design, in which dynamic properties will be improved. The research was divided into two stages. In the first stage, modal studies of the model and the real object were carried out. The obtained discrepancy between numerical and experimental results below 8% allows to state that the model is characterized by dynamic properties occurring in the real boring bar. In the second stage of the research, static tests were carried out. The object was loaded with forces of 98.6 N, 195.0 N, 293.8 N. The obtained slight discrepancy in the results of numerical and experimental tests below 3% allows to state that the model reflects the static properties of the real boring bar. The high convergence of the theoretical and experimental results allows for the conclusion that the numerical model has been verified positively.
- Open Access
- 1 January 2021
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 25 (1) , 6-14
Dynamic properties of hybrid machine tool body – Theoretical and experimental investigation
The article presents theoretical and experimental investigation in order to obtain dynamic properties of hybrid machine tool body in comparison with cast iron body. For this purpose, the theoretical and experimental modal analyses were carried out. The influence of the mineral cast material for filling voids on the dynamic properties of the machine tool body was discussed. During the analysis, the modes and frequencies of free vibrations, the amplitude values and the damping ratios were compared. Despite lowering the free vibration frequency of the hybrid construction, compared to the cast iron body, in some cases, the dynamic properties were affected. This could be determined on the basis of decreasing the amplitude value of the transfer function (from 12.16% to 58.66%) and the increasing the vibration damping coefficient ratio (from 12.22% to 75.24%) in the case of a hybrid body as compared to a cast iron body. The final conclusions were drawn about the application of mineral casts in the construction of machine tools and its impact on the dynamic properties of the structure.
- 1 January 2021
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 25 (1) , 6-14
Open AccessDynamic properties of hybrid machine tool body – Theoretical and experimental investigation
The article presents theoretical and experimental investigation in order to obtain dynamic properties of hybrid machine tool body in comparison with cast iron body. For this purpose, the theoretical and experimental modal analyses were carried out. The influence of the mineral cast material for filling voids on the dynamic properties of the machine tool body was discussed. During the analysis, the modes and frequencies of free vibrations, the amplitude values and the damping ratios were compared. Despite lowering the free vibration frequency of the hybrid construction, compared to the cast iron body, in some cases, the dynamic properties were affected. This could be determined on the basis of decreasing the amplitude value of the transfer function (from 12.16% to 58.66%) and the increasing the vibration damping coefficient ratio (from 12.22% to 75.24%) in the case of a hybrid body as compared to a cast iron body. The final conclusions were drawn about the application of mineral casts in the construction of machine tools and its impact on the dynamic properties of the structure.
- Open Access
- 1 January 2021
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 28 (1) , 343-351
Material-removing machining wastes as a filler of a polymer concrete (industrial chips as a filler of a polymer concrete)
The paper presents an impact of the addition of industrial machining chips on the mechanical properties of polymer concrete. As an additional filler, six types of industrial waste machining chips were used: steel fine chips, steel medium chips, steel thick chips, aluminium fine chips, aluminium medium chips, and titanium fine chips. During the research, the influence of the addition of chips on the basic parameters of mechanical properties, i.e., tensile strength, compressive strength, splitting tensile strength, and Young’s modulus, was analyzed. On the basis of the obtained results, conclusions were drawn that the addition of chips from machining causes a decrease in the value of the mechanical properties parameters of the polymer concrete even by 30%. The mechanism of cracking of samples, which were subjected to durability tests, was also explored. In addition, it was found that some chip waste can be used as a substitute for natural fillers during preparation of a mineral cast composition without losing much of the strength parameters.
- 1 January 2021
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 28 (1) , 343-351
Open AccessMaterial-removing machining wastes as a filler of a polymer concrete (industrial chips as a filler of a polymer concrete)
The paper presents an impact of the addition of industrial machining chips on the mechanical properties of polymer concrete. As an additional filler, six types of industrial waste machining chips were used: steel fine chips, steel medium chips, steel thick chips, aluminium fine chips, aluminium medium chips, and titanium fine chips. During the research, the influence of the addition of chips on the basic parameters of mechanical properties, i.e., tensile strength, compressive strength, splitting tensile strength, and Young’s modulus, was analyzed. On the basis of the obtained results, conclusions were drawn that the addition of chips from machining causes a decrease in the value of the mechanical properties parameters of the polymer concrete even by 30%. The mechanism of cracking of samples, which were subjected to durability tests, was also explored. In addition, it was found that some chip waste can be used as a substitute for natural fillers during preparation of a mineral cast composition without losing much of the strength parameters.
- Open Access
- 2 January 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (7-8) , 3017-3032
Influence of machining parameters on the polymer concrete milling process
The paper examines the wear of end mill cutters, the parameters of a workpiece’s surface layer and the values of cutting forces during the machining of polymer concrete, which is one of the most difficult-to-cut materials. Increased abrasive wear of the active cutting edges is a result of the heterogeneous structure of this material, and it has a negative effect on the cutting process, the durability of the cutting tools as well as the roughness of the workpiece. It is very important to determine the machining parameters for this material from a tool durability and quality of machining point of view. The research was divided into two stages. In the first stage, the appropriate machining parameters were determined based on the measurement of the components of the cutting force. In the second stage, durability tests of four end mill cutters were carried out. During the tests, the component cutting forces, tool wear and surface roughness were measured. The highest tool durability was recorded for the monolithic cemented carbide cutter with coating NC Mill G9F42120N 4F. Tools made of high-speed steel should not be used for machining polymer concrete, as they exhibited the highest intensity of tool wear. The rapid loss of machinability of these tools leads to a rapid increase in cutting force and the roughness of the machined surface. From an economic point of view, cemented carbide end mill cutters with coatings seem to be the appropriate choice for machining polymer concrete.
- 2 January 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (7-8) , 3017-3032
Open AccessInfluence of machining parameters on the polymer concrete milling process
The paper examines the wear of end mill cutters, the parameters of a workpiece’s surface layer and the values of cutting forces during the machining of polymer concrete, which is one of the most difficult-to-cut materials. Increased abrasive wear of the active cutting edges is a result of the heterogeneous structure of this material, and it has a negative effect on the cutting process, the durability of the cutting tools as well as the roughness of the workpiece. It is very important to determine the machining parameters for this material from a tool durability and quality of machining point of view. The research was divided into two stages. In the first stage, the appropriate machining parameters were determined based on the measurement of the components of the cutting force. In the second stage, durability tests of four end mill cutters were carried out. During the tests, the component cutting forces, tool wear and surface roughness were measured. The highest tool durability was recorded for the monolithic cemented carbide cutter with coating NC Mill G9F42120N 4F. Tools made of high-speed steel should not be used for machining polymer concrete, as they exhibited the highest intensity of tool wear. The rapid loss of machinability of these tools leads to a rapid increase in cutting force and the roughness of the machined surface. From an economic point of view, cemented carbide end mill cutters with coatings seem to be the appropriate choice for machining polymer concrete.
- 1 August 2019
- Published by Index Copernicus in Archives of Materials Science and Engineering
- Vol. 2 (98) , 74-80
Surface roughness of the Ti-6Al-4V ELI titanium alloy after the turning process
Purpose: The purpose of this article is discussing the methods of determining the surface roughness of the Ti-6Al-4V ELI titanium alloy obtained after longitudinal turning. The method of determining the mathematical model used for determining the Rz roughness parameter and then the results obtained were compared with values measured and calculated on the basis of equations available in the literature. Design/methodology/approach: The mathematical model in the form of multiple regression function of exponential polynomial was determined using the algorithm of the acceptance and rejection method. The data for calculations was obtained by measuring the surface roughness after turning with different machining parameter values. Findings: A mathematical model was elaborated in the form of a multiple regression function, enabling calculation of the Rz parameter describing the Ti-6Al-4V ELI titanium alloy surface roughness after longitudinal turning. The verification of the dependence obtained confirmed its accuracy. Research limitations/implications: Further research should encompass other values of machining plate geometry, as well as other types of cooling and lubricating fluids and method of applying them. Practical implications: The mathematical model can be helpful when choosing the conditions in which the turning process will be carried out. It also constitutes a basis for further optimisation of that process. Originality/value: The results of this research are a novelty on a worldwide scale. No research of this type has been conducted with regard to analyses and optimisation of longitudinal turning of the Ti-6Al-4V ELI titanium alloy.
- 1 August 2019
- Published by Index Copernicus in Archives of Materials Science and Engineering
- Vol. 2 (98) , 74-80
Surface roughness of the Ti-6Al-4V ELI titanium alloy after the turning process
Purpose: The purpose of this article is discussing the methods of determining the surface roughness of the Ti-6Al-4V ELI titanium alloy obtained after longitudinal turning. The method of determining the mathematical model used for determining the Rz roughness parameter and then the results obtained were compared with values measured and calculated on the basis of equations available in the literature. Design/methodology/approach: The mathematical model in the form of multiple regression function of exponential polynomial was determined using the algorithm of the acceptance and rejection method. The data for calculations was obtained by measuring the surface roughness after turning with different machining parameter values. Findings: A mathematical model was elaborated in the form of a multiple regression function, enabling calculation of the Rz parameter describing the Ti-6Al-4V ELI titanium alloy surface roughness after longitudinal turning. The verification of the dependence obtained confirmed its accuracy. Research limitations/implications: Further research should encompass other values of machining plate geometry, as well as other types of cooling and lubricating fluids and method of applying them. Practical implications: The mathematical model can be helpful when choosing the conditions in which the turning process will be carried out. It also constitutes a basis for further optimisation of that process. Originality/value: The results of this research are a novelty on a worldwide scale. No research of this type has been conducted with regard to analyses and optimisation of longitudinal turning of the Ti-6Al-4V ELI titanium alloy.