MSMałgorzata Sikora

Małgorzata Sikora

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Małgorzata Sikora has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Machining Parameters on the Surface Roughness and Tool Wear During Slot Milling of a Polyurethane Block

    by Karolina Szadkowska, Norbert Kępczak, Wojciech Stachurski, Witold Pawłowski, Radosław Rosik, Grzegorz Bechciński, Małgorzata Sikora, Błażej Witkowski, Jakub Sikorski

    The aim of the work was to investigate the influence of the machining parameters on the surface roughness and tool wear during slot milling of a polyurethane block (PUB). In the experiment, the influence of the cutting speed, the feed per tooth and the depth of cut on the roughness Ra and Rz of the milling slot surface and wear of the end mill was analyzed. A three-axis CNC milling machine Emco Concept Mill 55 was used to perform the study. After the machining, the values of parameters Ra and Rz were measured using the Hommel Tester T500 induction profilometer. Three polyurethane materials of different densities were considered: the Labelite 45, the Prolab 65 and the LAB 1000. The wear of the end mill was also examined for each of the tested materials by a workshop microscope. In conclusion, it was indicated how and to what extent the variation in the machining parameters affects the surface geometrical structure of a polyurethane plate. Moreover, the research results for the tested materials were compared with each other.


  • Open Access

    Mathematical Models of Grinding Forces in the Hob Cutter Sharpening Process

    by Błażej Witkowski, Wojciech Stachurski, Witold Pawłowski, Małgorzata Sikora, Norbert Kępczak

    The article presents the results of research aimed at developing mathematical models for determining the components of grinding force occurring during the sharpening of the rake face of hob cutters. The development of the models was based on the results obtained during experimental tests conducted in the first stage of the research. The studies were carried out using a tool grinder and an aluminum oxide grinding wheel. During the tests, two components of the grinding force were measured, using a piezoelectric dynamometer. A sample made of HS6-5-2 high-speed steel was ground. Grinding was carried out using different sets of cutting parameters. Based on the obtained measurement results, two mathematical models were developed in the form of (1) a multiple regression function and (2) a polynomial function, enabling the calculation of the normal and the tangential force. The experimentally obtained results were then compared with those calculated based on the developed models, and the results of this comparison showed that the developed models provide a good basis for analyzing the sharpening process of hob cutters in terms of variable grinding parameters.


  • Open Access

    The influence of grinding conditions on surface roughness parameters of 20MnCr5 steel vacuum-carburised by single-piece flow method

    by M Sikora, P Zgórniak, E Wołowiec-Korecka

    The purpose of the experimental tests described in the article was to determine the effect of selected abrasive machining conditions on the value of surface roughness of 20MnCr5 steel samples. The samples were subjected to vacuum carburising (LPC) using the ‘single-piece flow’ method and high-pressure gas quenching (HPGQ) in a 4D Quenching chamber to obtain an effective case depth (ECD) of 0.4 mm. Next, the samples were ground with a Norton Vortex corundum grinding wheel. Cooling and lubricating fluid was delivered to the grinding zone using the flooding method (WET) and with the minimum quantity lubrication method (MQL). The samples were ground in one pass of the grinding wheel using two grinding depths – ae = 0.01 mm and ae = 0.02 mm. For each grinding test, surface roughness measurements were made using a stationary laboratory profilometer T8000 from Hommel Werke. These measurements enabled the determination of the 2D and 3D roughness parameters. Analysis of the measurement results showed that for the adopted test conditions, the use of the MQL method resulted in a decrease in surface roughness compared to the surface ground using the WET method. This property applies to both tested grinding depths.


  • Open Access

    Influence of machining parameters on the polymer concrete milling process

    by Norbert Kepczak, Piotr Zgorniak, Paweł Lajmert, Radoslaw Rosik, Malgorzata Sikora

    The paper examines the wear of end mill cutters, the parameters of a workpiece’s surface layer and the values of cutting forces during the machining of polymer concrete, which is one of the most difficult-to-cut materials. Increased abrasive wear of the active cutting edges is a result of the heterogeneous structure of this material, and it has a negative effect on the cutting process, the durability of the cutting tools as well as the roughness of the workpiece. It is very important to determine the machining parameters for this material from a tool durability and quality of machining point of view. The research was divided into two stages. In the first stage, the appropriate machining parameters were determined based on the measurement of the components of the cutting force. In the second stage, durability tests of four end mill cutters were carried out. During the tests, the component cutting forces, tool wear and surface roughness were measured. The highest tool durability was recorded for the monolithic cemented carbide cutter with coating NC Mill G9F42120N 4F. Tools made of high-speed steel should not be used for machining polymer concrete, as they exhibited the highest intensity of tool wear. The rapid loss of machinability of these tools leads to a rapid increase in cutting force and the roughness of the machined surface. From an economic point of view, cemented carbide end mill cutters with coatings seem to be the appropriate choice for machining polymer concrete.


  • Surface roughness of the Ti-6Al-4V ELI titanium alloy after the turning process

    by R. Rosik, N. Kępczak, M. Sikora, B. Witkowski, R. Wójcik, S. Midera

    Purpose: The purpose of this article is discussing the methods of determining the surface roughness of the Ti-6Al-4V ELI titanium alloy obtained after longitudinal turning. The method of determining the mathematical model used for determining the Rz roughness parameter and then the results obtained were compared with values measured and calculated on the basis of equations available in the literature. Design/methodology/approach: The mathematical model in the form of multiple regression function of exponential polynomial was determined using the algorithm of the acceptance and rejection method. The data for calculations was obtained by measuring the surface roughness after turning with different machining parameter values. Findings: A mathematical model was elaborated in the form of a multiple regression function, enabling calculation of the Rz parameter describing the Ti-6Al-4V ELI titanium alloy surface roughness after longitudinal turning. The verification of the dependence obtained confirmed its accuracy. Research limitations/implications: Further research should encompass other values of machining plate geometry, as well as other types of cooling and lubricating fluids and method of applying them. Practical implications: The mathematical model can be helpful when choosing the conditions in which the turning process will be carried out. It also constitutes a basis for further optimisation of that process. Originality/value: The results of this research are a novelty on a worldwide scale. No research of this type has been conducted with regard to analyses and optimisation of longitudinal turning of the Ti-6Al-4V ELI titanium alloy.


  • Open Access

    A dynamic model of cylindrical plunge grinding process for chatter phenomena investigation

    by Paweł Lajmert, Małgorzata Sikora, Dariusz Ostrowski

    In the paper, chatter vibrations in the cylindrical plunge grinding process are investigated. An improved model of the grinding process was developed which is able to simulate self-excited vibrations due to a regenerative effect on the workpiece and the grinding wheel surface. The model includes a finite-element model of the workpiece, two degrees of freedom model of the grinding wheel headstock and a model of wheel-workpiece geometrical interferences. The model allows to studying the influence of different factors, i.e. workpiece and machine parameters as well as grinding conditions on the stability limit and a chatter vibration growth rate. At the end, simulation results are shown and compared with exemplified real grinding results.


  • THE DYNAMICS OF WEAR OF CUTTING INSERTS DURING TURNING OF NON-HOMOGENEOUS MATERIAL ON THE EXAMPLE OF POLYMER CONCRETE

    by Norbert Kępczak, Radosław Rosik, Witold Pawłowski, Małgorzata Sikora, Błażej Witkowski, Grzegorz Bechciński, Wojciech Stachurski


  • The influence of machining conditions of Hastelloy C-276 on the effects of grinding process

    by Małgorzata Sikora, Bogdan Kruszyński, Paweł Lajmert

    Artykuł Badanie wpływu warunków szlifowania stopu Hastelloy C-276 na efekty procesu szlifowania * | Mechanik Miesięcznik Naukowo-Techniczny