VNVitaly O. Nekhoroshev

Vitaly O. Nekhoroshev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Vitaly O. Nekhoroshev has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Application of Pulse Gas-Discharge Electroacoustic Transducer for Non-Destructive Testing

    by D. A. Derusova, V. O. Nekhoroshev, V. Yu. Shpilnoy, A. V. Raut, Шпильной В. Ю.

    This paper presents the results of a gas-discharge electro acoustic transducer of two configurations, operating on the basis of a pulsed discharge in air at atmospheric pressure. The influence of the electrode configuration on the acoustic characteristics of the transducer is considered. It is shown that a change in the volume of the discharge chamber and the inter electrode gap have a significant effect on the radiation intensity of the transducer. The features that arise when using open and closed type electro acoustic transducers in flaw detection problems are revealed. It is shown that an open type gas-discharge electroacoustic transducer is a sufficiently powerful broadband source of the excitation signal and has prospects for use in non-destructive testing. A closed type gas-discharge electroacoustic transducer has advantages when testing materials with special requirements for surface cleanliness or the magnitude of the applied external electric field.

  • Application of Pulse Gas-Discharge Electroacoustic Transducer for Nondestructive Testing

    by D. A. Derusova, V. O. Nekhoroshev, V. Yu. Shpil’NOy, A. V. Raut

    The results of the study of a gas-discharge electroacoustic transducer operating based on a pulse discharge in air at atmospheric pressure are presented. The influence of the electrode system configuration on the acoustic characteristics of the transducer is considered. It is shown that changing the discharge chamber volume and the interelectrode gap significantly affects the radiation intensity. Features that arise when using electroacoustic transducers of open and closed types for NDT tasks are identified. It is demonstrated that the open-type gas-discharge electroacoustic transducer is a sufficiently powerful broadband excitation signal source and has prospects for application in non-destructive testing. The closed-type gas-discharge electroacoustic transducer has advantages when studying materials with special requirements for surface cleanliness or the magnitude of the applied external electric field.


  • Analysis and NDT Applications of a Gas Discharge Electroacoustic Transducer

    by D. A. Derusova, V. P. Vavilov, V. O. Nekhoroshev, V. Yu. Shpil’NOy, D. A. Zuza, E. N. Kolobova

    In this study, a gas discharge electroacoustic transducer (GDEAT) based on a pulsed electric discharge in the air under atmospheric pressure has been investigated. The acoustic characteristic of GDEATs have been determined in the frequency range from 40 Hz to 4 MHz by evaluating acoustic pressure and recording amplitude–frequency characteristics of membranes. The electrothermoacoustic processes have been studied in open type gas discharge systems where the electrode space is in a direct contact with the environment. Some features of using the above-mentioned GDEATs in material nondestructive testing (NDT) have been demonstrated. It has been shown that, on the one hand, the wear of both electrodes and insulation limits the work life of transducer’s electrode system; however, on the other hand, this may lead to deposition of microparticles on the test object surface. The wear of the electrode system was evaluated quantitatively. The results of the chemical analysis of the deposited microparticles are presented. The possibility of using GDEATs for noncontact stimulation of local resonant vibrations in subsurface defects and visualizing vibrations by means of laser Doppler vibrometry is shown in the case of NDT of a glass fiber composite.


  • A Study of the Plasma Jet Formed by the Glow Discharge in an Air Flow in the Electrode System of a Gliding Arc

    by N. V. Landl, V. O. Nekhoroshev, Y. D. Korolev, O. B. Frants, V. S. Kasyanov


  • Open Access

    Organosilicon coating mass distribution in plasma-chemical reactor based on glow discharge in gas flow

    by Institute of High Current Electronics of the Siberian Branch of RAS, Даниил Александрович Зуза, Vitaly O. Nekhoroshev, Alexander V. Batrakov, Irina A. Kurzina, Tomsk State University

    Using the Plasma-Enhanced Chemical Vapour Deposition (PECVD) method, it is possible to synthesize a wide range of different materials, in particular, organosilicon polymer-like coatings. In the present work, a plasma-chemical reactor with coaxial hollow electrodes based on a DC glow discharge maintained in a plasmaforming gas flow at low pressure is used for deposition of a polymer-like coating. Argon was used as a plasma gas with a flow rate of 230 mg/min. Hexamethyldisiloxane was used as a precursor for deposition. Hexamethyldisiloxane was a molecular impurity in the inert gas flow and its flow rate was 10 mg/min. The purpose of the present work is an experimental study of the mass distribution of deposited organosilicon polymer-like coating on various constituent parts of the plasma chemical system based on glow discharge - on the internal surfaces of the reactor and on the substrate located at a distance of 15 mm from the reactor outlet. The experiment showed that at a discharge power of 30 W the total measured mass of the coating amounted to 33 mg. Thus, the mass conversion of the initial substance was over 33%. It is shown that about 90% of the total measured mass of the coating was deposited inside the plasma chemical reactor - on the inner surface of the hollow cathode and the inner surface of the glass tube, and 10% on the substrate. Thus, the present system can be used not only for remote local deposition but also for coating the inner walls of the tubes with a polymer-like coating. It was also revealed that due to the different conditions of processes in the cathode layers and the plasma of the positive column of the glow discharge, some peculiarities of deposition on different surfaces in the system appear. For example, the microstructure of the coatings obtained on the cathode, on the glass tube and on the substrate was investigated using an optical microscope. In this way it was revealed that the coatings consist of rounded microparticles and have a significant difference - the average size of microparticles on the glass tube and substrate cathode is 2-5 microns, which is an order of magnitude lower than the average size of particles deposited on the cathode.

  • Open Access

    Chemical constitution of coatings deposited under hexamethyldisiloxane activation in a glow discharge in a gas flow

    by Institute of High Current Electronics of the Siberian Branch of RAS, Даниил Александрович Зуза, Vitaly O. Nekhoroshev, Alexander V. Batrakov, Irina A. Kurzina, Tomsk State University

    The aim of the present work is to reveal peculiarities and regularities of formation of chemical constitution of polymer-like coatings deposited under plasmachemical activation of hexamethyldisiloxane in cathode layers and positive column plasma of glow discharge. The glow discharge was maintained in an argon/hexamethyldisiloxane mixture flow. The argon flow rate was 230 mg/min. The coatings were deposited in six different modes of the plasma-chemical system. The modes were determined by the flow rate of hexamethyldisiloxane, which ranged from 1 to 10 mg/min, and the average discharge current, which was set between 5 and 50 mA. The chemical constitution of the obtained coatings was identified using X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. It is shown that varying the discharge current and hexamethyldisiloxane flow rate in this system produces a wide range of coatings of different chemical constitution. Four different types of coatings obtained were identified: polymethylsiloxane-like structure cross-linked with aliphatic hydrocarbon links with high (C/Si = 9.4) and low (C/Si = 2.9) hydrocarbon linkages, polyhedral oligomeric silsesquioxanes cross-linked with carbosilane, siloxane and aliphatic links with high (C/Si = 5.1) and low (C/Si = 1.5) hydrocarbon linkages. A significant effect of hexamethyldisiloxane flow rate on the chemical structure was found. The most interesting feature of some of the obtained organosilicon coatings is the high relative carbon content. The amount of hydrocarbon links in the coating was found to increase with discharge current. The assumption of formation of hydrocarbon film-forming particles in the cathode layers of the discharge due to ion-induced processes is put forward.

  • Initial stages of pulsed discharge in saline solutions in a vicinity of threshold voltages

    by Y D Korolev, N V Landl, A V Bolotov, V S Kasyanov, V O Nekhoroshev, I A Shemyakin

    Data are presented on an investigation of pulsed discharges in a solution of 30 g of NaCl per liter of distilled water. The interelectrode gap consists of the active pin electrode and the return plane electrode. The voltage pulse of positive polarity forms by means of an electric circuit where a capacitor bank of 40 μ F with an initial voltage V 0 of up to 1500 V is discharged via the gap. In a range of initial voltages V 0 = (550 – 1100) V vapor cavities in a form of the microbubbles are generated near the active electrode and at the electrode surface. The microbubbles are able to merge with each other thus forming macrobubbles and vapor layers, which shield the active electrode from current passage. The process of vapor cavity generation and the effect of shielding are discussed in detail. The discharge at the vapor layer appears at the critical voltage V 0 = 1100 V. The principal prerequisite for discharge arising is that the electrode has to be completely shielded by the vapor layer and the voltage at the layer at the instant of discharge initiation has to be at least at a level of 500 V. However, when the voltage at the gap exceeds the critical value, the condition of complete shielding is not obligatory.


  • Open Access

    Nonsteady-state processes in a low-current discharge in airflow and formation of a plasma jet

    by Y D Korolev, V O Nekhoroshev, O B Frants, N V Landl, A I Suslov, V G Geyman

    The paper describes the investigations of a low-current discharge in airflow with the electrode configuration of coaxial plasmatron. An inner diameter of the plasmatron nozzle is of 0.5 cm and the mass airflow rate is from 0.1 to 0.3 g s−1. Typical averaged discharge current is varied from 0.06 to 0.2 A. In these conditions, due to airflow the so-called plasma jet forms in the plasmatron nozzle and at its exit. The total current in plasmatron mainly flows via the constricted plasma column of the glow discharge and only a small fraction of current is carried by the jet. The principal idea of the experiments is to reveal the mechanism of the jet formation and to elucidate how the nonsteady discharge regimes influence on the jet properties. We have proposed the method for the jet diagnostics, which is based on measuring the currents to the additional diagnostic electrodes located outside the nozzle. The obtained data show that the jet current forms due to electrons that are emitted from the boundary of plasma column. The temporal behavior of the jet current is determined by the position of the column inside the plasmatron nozzle, which changes with time. Hence, the term ‘plasma jet’ has to be used with care, since the charged particles in the jet area are the electrons. The estimated electron density in the jet is of about 109 cm–3.