Qingjun Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qingjun Liu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ze Jiang
Jiangsu University, Engineering Institute of Advanced Manufacturing and Modern Equipment Technology, China, Zhenjiang, ZhenJiang, JiangSu, 212013, CHINA
10 shared publications - Hao Chen
Jiangsu University, Engineering Institute of Advanced Manufacturing and Modern Equipment Technology, ZhenJiang, JiangSu, CHINA
9 shared publications - Xu Zhang
Research Institute of Safety & Environment Technology, China National Petroleum Corporation, Beijing 102206, China
9 shared publications - Qiang Mao
Engineering Institute of Advanced Manufacturing and Modern Equipment Technology, Jiangsu University, Zhenjiang,Chin, Zhenjiang, 212013, CHINA
8 shared publications - Tianci Zhang
Jiangsu University, Zhenjiang, 212013, CHINA
7 shared publications - Vitus Mwinteribo Tabie
Department of Mechanical Engineering Wa Polytechnic, Ghana, P. O. Box 553, Wa, UWR, GHANA
5 shared publications
Latest Publications
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265g4
Effect of solid solution heat treatment following age hardening on microstructure and mechanical properties of 7000 series power aluminum alloy
In this paper, Al-11.1Zn-2.7Mg-1.7Cu-1.4Ti-0.2Zr alloy material was prepared by powder metallurgy to study the effect of the different solid-solution aging systems on the microstructure and mechanical properties of this 7000 series aluminum alloy. The microstructure of the alloy under the three different solid-solution processes S1, S2, and S3 were observed using an optical microscope, scanning electron microscope, and X-ray diffraction analysis. The mechanical properties were tested to determine the best solid-solution process. The results show that under the S2 solid-solution process, the alloy has the best mechanical properties, with a compressive strength of 646.7(±6.5) MPa and a fracture strain of 5.9(±0.06)%. The maximum hardness trends in the three solid-solution processes after aging are S2>S3>S1. The maximum hardness 220.7(±5.5 )HV occurs after S2 solid-solution and 121℃×18 h aging. Moreover, after S2 solid-solution treatment, the solid-solution degree is close to saturation, the solid-solution strengthening effect is the best, and dislocations contribute the most to the strength.
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265g4
Open AccessEffect of solid solution heat treatment following age hardening on microstructure and mechanical properties of 7000 series power aluminum alloy
In this paper, Al-11.1Zn-2.7Mg-1.7Cu-1.4Ti-0.2Zr alloy material was prepared by powder metallurgy to study the effect of the different solid-solution aging systems on the microstructure and mechanical properties of this 7000 series aluminum alloy. The microstructure of the alloy under the three different solid-solution processes S1, S2, and S3 were observed using an optical microscope, scanning electron microscope, and X-ray diffraction analysis. The mechanical properties were tested to determine the best solid-solution process. The results show that under the S2 solid-solution process, the alloy has the best mechanical properties, with a compressive strength of 646.7(±6.5) MPa and a fracture strain of 5.9(±0.06)%. The maximum hardness trends in the three solid-solution processes after aging are S2>S3>S1. The maximum hardness 220.7(±5.5 )HV occurs after S2 solid-solution and 121℃×18 h aging. Moreover, after S2 solid-solution treatment, the solid-solution degree is close to saturation, the solid-solution strengthening effect is the best, and dislocations contribute the most to the strength.
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265b7
Effect of La2O3 on resistance to high-temperature oxidation and corrosion of aluminized and aluminum-chrome coating
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265b7
Open AccessEffect of La2O3 on resistance to high-temperature oxidation and corrosion of aluminized and aluminum-chrome coating
- 25 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126593
Effect of pre-recovery and aging treatment on anisotropy of microstructure and properties of Al–7.0Zn–1.41Mg–1.50Cu–0.14Zr–0.023 Sr alloy
The Al - 7.0Zn - 1.41Mg - 1.50Cu - 0.14Zr - 0.023Sr alloy (7085 aluminum alloy) was treated by hot compression-solution and aging treatment (CS) and hot compression-pre-recovery-solution and aging treatment (CPS), respectively. Electron Backscatter Diffraction Analysis (EBSD), X-ray Diffraction Analysis (XRD), Optical Microscope (OM), Conductivity Test, Tensile Test and Intergranular Aging were used to study the effect of pre-recovery on the anisotropy of structure and properties of 7085 aluminum alloy treated by hot compression and aging treatment. The results show that pre-recovery treatment can restrain recrystallization, refine grains and significantly increase the percentage of low-angle grain boundary. After the pre-recovery treatment, the average grain size in Y direction changes from 18.016 μm to 10.650 μm, and the proportion of low-angle grain boundary increases from 42.3% to 76.0%. The hardness of the alloy increased slightly, and the electrical conductivity of the alloy decreased. And the intergranular corrosion resistance of 7085 alloy has been greatly improved, especially in Y direction, which has increased by nearly 69.5%.
- 25 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126593
Effect of pre-recovery and aging treatment on anisotropy of microstructure and properties of Al–7.0Zn–1.41Mg–1.50Cu–0.14Zr–0.023 Sr alloy
The Al - 7.0Zn - 1.41Mg - 1.50Cu - 0.14Zr - 0.023Sr alloy (7085 aluminum alloy) was treated by hot compression-solution and aging treatment (CS) and hot compression-pre-recovery-solution and aging treatment (CPS), respectively. Electron Backscatter Diffraction Analysis (EBSD), X-ray Diffraction Analysis (XRD), Optical Microscope (OM), Conductivity Test, Tensile Test and Intergranular Aging were used to study the effect of pre-recovery on the anisotropy of structure and properties of 7085 aluminum alloy treated by hot compression and aging treatment. The results show that pre-recovery treatment can restrain recrystallization, refine grains and significantly increase the percentage of low-angle grain boundary. After the pre-recovery treatment, the average grain size in Y direction changes from 18.016 μm to 10.650 μm, and the proportion of low-angle grain boundary increases from 42.3% to 76.0%. The hardness of the alloy increased slightly, and the electrical conductivity of the alloy decreased. And the intergranular corrosion resistance of 7085 alloy has been greatly improved, especially in Y direction, which has increased by nearly 69.5%.
- 25 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126597
Effect of SiCw volume fraction and cold pressure on microstructure and mechanical properties of aluminum matrix composites
The alloy powder and SiCw reinforcement were ball milled, cold-pressed, sintered, hot extruded and solution aged to obtain excellent mechanical properties such as hardness and compressive strength. The microstructure and properties of the material were characterized by metallographic microscope, scanning electron microscope (SEM), EDS, X-ray diffraction (XRD), HV-1000 microhardness and 7051 eddy current conductivity. The results show that the distribution of SiC whiskers in the mixed powder is relatively uniform, but there is still a small amount of agglomeration phenomenon in the sintered sample. The optimum cold pressure is 740 MPa. With the increase in SiCw content, the hardness, dislocation density and compressive strength of aluminum matrix composites are improved. The compressive strength of 5%SiCw reinforced aluminum matrix composite is 658.9 MPa and the elongation is 6.7%.
- 25 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126597
Effect of SiCw volume fraction and cold pressure on microstructure and mechanical properties of aluminum matrix composites
The alloy powder and SiCw reinforcement were ball milled, cold-pressed, sintered, hot extruded and solution aged to obtain excellent mechanical properties such as hardness and compressive strength. The microstructure and properties of the material were characterized by metallographic microscope, scanning electron microscope (SEM), EDS, X-ray diffraction (XRD), HV-1000 microhardness and 7051 eddy current conductivity. The results show that the distribution of SiC whiskers in the mixed powder is relatively uniform, but there is still a small amount of agglomeration phenomenon in the sintered sample. The optimum cold pressure is 740 MPa. With the increase in SiCw content, the hardness, dislocation density and compressive strength of aluminum matrix composites are improved. The compressive strength of 5%SiCw reinforced aluminum matrix composite is 658.9 MPa and the elongation is 6.7%.
- 17 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126510
Hot corrosion resistance of a Ti–Mo–Nb–Al–Si titanium matrix composites reinforced with in-situ TiC prepared by powder metallurgy
A mixture of the Ti-Mo-Nb-Al-Si matrix powder and Carbon nanotubes (CNTs) particles were used as the raw powder to produce the in-situ TiC reinforced titanium matrix composites (TMCs) via powder metallurgy. The effects of various contents of CNTs on the microstructure, phase composition and hot corrosion behavior of the composites were investigated. The results show that the corrosion mass gain of the composites with CNTs content of 1.0 wt.% was the minimum (18.73 mgcm-2), which was about 44.4% lighter than that of the matrix (33.70 mgcm-2). XRD results show that the corrosion phases were mainly composed of TiO2, Al2O3, SiO2, Ti(SO4)2, NaTiO2 and TiS. According to the SEM results, the grain size of the as-sintered composites can be refined by adding CNTs. With the increase of CNTs content, the grain size became smaller and smaller. The cross-sectional morphology shows that the oxide layer of the composites with 1.0 wt.% CNTs after corrosion was denser and thinner (21.44 μm). It was about 82.13% thinner than the oxide layer of the matrix (120.00 μm). All the results show that the TMCs with 1.0 wt.% CNTs have better hot corrosion resistance.
- 17 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126510
Hot corrosion resistance of a Ti–Mo–Nb–Al–Si titanium matrix composites reinforced with in-situ TiC prepared by powder metallurgy
A mixture of the Ti-Mo-Nb-Al-Si matrix powder and Carbon nanotubes (CNTs) particles were used as the raw powder to produce the in-situ TiC reinforced titanium matrix composites (TMCs) via powder metallurgy. The effects of various contents of CNTs on the microstructure, phase composition and hot corrosion behavior of the composites were investigated. The results show that the corrosion mass gain of the composites with CNTs content of 1.0 wt.% was the minimum (18.73 mgcm-2), which was about 44.4% lighter than that of the matrix (33.70 mgcm-2). XRD results show that the corrosion phases were mainly composed of TiO2, Al2O3, SiO2, Ti(SO4)2, NaTiO2 and TiS. According to the SEM results, the grain size of the as-sintered composites can be refined by adding CNTs. With the increase of CNTs content, the grain size became smaller and smaller. The cross-sectional morphology shows that the oxide layer of the composites with 1.0 wt.% CNTs after corrosion was denser and thinner (21.44 μm). It was about 82.13% thinner than the oxide layer of the matrix (120.00 μm). All the results show that the TMCs with 1.0 wt.% CNTs have better hot corrosion resistance.
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 1165f4
Effect of SiCw volume fraction on microstructure and properties of SiCw/Al composite fabricated by hot isostatic pressing-hot pressing
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 1165f4
Effect of SiCw volume fraction on microstructure and properties of SiCw/Al composite fabricated by hot isostatic pressing-hot pressing
- 30 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 1065a3
Effect of SiCp volume fraction on microstructure and properties of powder metallurgy SiCp reinforced aluminum matrix composites
- 30 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 1065a3
Effect of SiCp volume fraction on microstructure and properties of powder metallurgy SiCp reinforced aluminum matrix composites
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106577
Effect of solution and aging system on microstructure and mechanical properties of 7000 series aluminum alloy produced by powder metallurgy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106577
Effect of solution and aging system on microstructure and mechanical properties of 7000 series aluminum alloy produced by powder metallurgy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106559
Anisotropy of microstructure and properties of Al-10.22 Zn-2.87 Mg-1.2 Cu-0.213 Zr alloy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106559
Anisotropy of microstructure and properties of Al-10.22 Zn-2.87 Mg-1.2 Cu-0.213 Zr alloy
- 19 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106426
Effect of submicron Sn on wear resistance and scale resistance of Ni–P–Sn composite coating
In this experiment, the microstructure and mechanical properties of Ni-P-Sn composite coatings with different Sn contents were observed by scanning electron microscope, optical contact angle measuring instrument, Vickers hardness tester and other experimental equipment. The effects of different Sn contents on wear resistance and scale resistance of Ni-P-Sn composite coatings were studied. The friction and wear properties of composite coatings with different Sn contents are tested and analyzed on friction and wear instruments, and the influence of Sn content on the scale resistance of composite coatings is analyzed through surface free energy and scale adhesion experiments. The results show that by measuring the hardness values of Ni-P- submicron Sn(2 g/L) coating, Ni-P coating and Q235, it is found that the hardness value of Ni-P- Sn composite coating is the highest, 434.9HV. At the same time, it is concluded that adding Sn to Ni-P composite coating is helpful to reduce the friction coefficient of the coating. The friction coefficient of Ni-P-Sn composite coating (6 g/L) is 16.04% lower than that of the coating without Sn. When Sn content is 6 g/L, the wear resistance is the best. When Sn content is 2 g/L, the contact angle is 120.2° at the maximum. The minimum surface free energy is 15 MJ/m2. The dirt weight gain is the minimum value of 85 g/m2. At this time, the anti-fouling performance is the best.
- 19 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106426
Effect of submicron Sn on wear resistance and scale resistance of Ni–P–Sn composite coating
In this experiment, the microstructure and mechanical properties of Ni-P-Sn composite coatings with different Sn contents were observed by scanning electron microscope, optical contact angle measuring instrument, Vickers hardness tester and other experimental equipment. The effects of different Sn contents on wear resistance and scale resistance of Ni-P-Sn composite coatings were studied. The friction and wear properties of composite coatings with different Sn contents are tested and analyzed on friction and wear instruments, and the influence of Sn content on the scale resistance of composite coatings is analyzed through surface free energy and scale adhesion experiments. The results show that by measuring the hardness values of Ni-P- submicron Sn(2 g/L) coating, Ni-P coating and Q235, it is found that the hardness value of Ni-P- Sn composite coating is the highest, 434.9HV. At the same time, it is concluded that adding Sn to Ni-P composite coating is helpful to reduce the friction coefficient of the coating. The friction coefficient of Ni-P-Sn composite coating (6 g/L) is 16.04% lower than that of the coating without Sn. When Sn content is 6 g/L, the wear resistance is the best. When Sn content is 2 g/L, the contact angle is 120.2° at the maximum. The minimum surface free energy is 15 MJ/m2. The dirt weight gain is the minimum value of 85 g/m2. At this time, the anti-fouling performance is the best.