Jitendra Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jitendra Kumar has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Tarun Soota
Department of Mechanical Engineering, Bundelkhand Institute of Engineering and Technology Jhansi, Uttar Pradesh, India
7 shared publications- S. K. Rajput
Department of Mechanical Engineering, Bundelkhand Institute of Engineering and Technology, Jhansi, India
2 shared publications S.K. Rajput
2 shared publicationsA Shukla
Bundelkhand Institute of Engineering and Technology, Jhansi, U.P., India 284001
1 shared publicationAmit Kumar
Bundelkhand Institute of Engineering and Technology
1 shared publicationFaijan Khan
1 shared publication
Latest Publications
- 13 March 2022
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 37 (15) , 1746-1755
Machining of Zircaloy-2 using progressive tool design in EDM
Zircaloy-2 is used in nuclear and biomedical industries therefore required high accuracy and precision, and achieved by application of electrical discharge machine (EDM). In this study, a new horizon of tool design is investigated for improvement in the performance of EDM. To measure the effect of tool design, Zircaloy-2 is machined with EDM using progressive Cu tool and measured the response parameters (MRR, TWR, radial overcut (Roc), radial undercut (Ruc), taper angle (Φ), and surface roughness). The progressive tool with varying design parameters of rake angle (0°, 45°, and 60°), flat land (2 mm), trunk diameters (10, 8, and 6 mm), and relief angle (0°, 45°, and 60°) are used to perform rough and finish machining in single EDM operation. MRR and SR are increased with increase in rake angle due to reduction in oxide and carbide deposition on the machined surface. Best combination for maximum MRR (1.131 × 10−3 mm3/min), minimum SR (4.313 µm), and minimum taper angle (2.17°) is obtained when machining is performed using T7. Multiresponse optimization (R-method) gives highest rank to progressive tool T7. Tool design improved TWR and significant reduction in radial overcut over conventional tool.
- 13 March 2022
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 37 (15) , 1746-1755
Machining of Zircaloy-2 using progressive tool design in EDM
Zircaloy-2 is used in nuclear and biomedical industries therefore required high accuracy and precision, and achieved by application of electrical discharge machine (EDM). In this study, a new horizon of tool design is investigated for improvement in the performance of EDM. To measure the effect of tool design, Zircaloy-2 is machined with EDM using progressive Cu tool and measured the response parameters (MRR, TWR, radial overcut (Roc), radial undercut (Ruc), taper angle (Φ), and surface roughness). The progressive tool with varying design parameters of rake angle (0°, 45°, and 60°), flat land (2 mm), trunk diameters (10, 8, and 6 mm), and relief angle (0°, 45°, and 60°) are used to perform rough and finish machining in single EDM operation. MRR and SR are increased with increase in rake angle due to reduction in oxide and carbide deposition on the machined surface. Best combination for maximum MRR (1.131 × 10−3 mm3/min), minimum SR (4.313 µm), and minimum taper angle (2.17°) is obtained when machining is performed using T7. Multiresponse optimization (R-method) gives highest rank to progressive tool T7. Tool design improved TWR and significant reduction in radial overcut over conventional tool.
- 14 April 2021
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 36 (13) , 1513-1523
Machining and optimization of Zircaloy-2 using different tool electrodes
To explore machining parameters for tool wear rate, surface roughness, and material removal rate, Zircaloy-2 was machined with EDM using Cu, CuW and graphite tool. Taguchi L18 Design was used to perform experiments with five independent process parameters (tool material, on-time, off-time, polarity, and current). Response parameters were evaluated and optimized using gray relation analysis and entropy-integrated-gray-VIKOR methods. FESEM was used to observe tool material and oxide layer deposition on machined surface. Maximum material removal rate (1.53 × 10−3 mm3/min) was obtained when the graphite tool with negative tool polarity was used. A confirmation test performed on the optimal factor level process parameters gives an error of 1.9%, 6.4%, and 9.8% for TWR, SR, and MRR respectively.
- 14 April 2021
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 36 (13) , 1513-1523
Machining and optimization of Zircaloy-2 using different tool electrodes
To explore machining parameters for tool wear rate, surface roughness, and material removal rate, Zircaloy-2 was machined with EDM using Cu, CuW and graphite tool. Taguchi L18 Design was used to perform experiments with five independent process parameters (tool material, on-time, off-time, polarity, and current). Response parameters were evaluated and optimized using gray relation analysis and entropy-integrated-gray-VIKOR methods. FESEM was used to observe tool material and oxide layer deposition on machined surface. Maximum material removal rate (1.53 × 10−3 mm3/min) was obtained when the graphite tool with negative tool polarity was used. A confirmation test performed on the optimal factor level process parameters gives an error of 1.9%, 6.4%, and 9.8% for TWR, SR, and MRR respectively.
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 1151-1158
Experimental evaluation and modelling of wire-EDM process parameter for stainless steel AISI 630
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 1151-1158
Experimental evaluation and modelling of wire-EDM process parameter for stainless steel AISI 630
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 21, 1544-1550
Multi-response optimization of machining parameter for Zircaloy by response surface methodology and grey relation analysis
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 21, 1544-1550
Multi-response optimization of machining parameter for Zircaloy by response surface methodology and grey relation analysis
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 25, 635-638
Optimization of EDM process parameter for stainless steel D3
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 25, 635-638
Optimization of EDM process parameter for stainless steel D3
- Open Access
- 1 November 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 691 (1) , 012003
Performance characteristics of non-edible Jatropha oil with adjustable compression ratios
Non-edible biodiesel extracted from jatropha oil is broadly studied to solve the twin problem of reduction of fossil fuels and environmental degradation. The present study is conducted on unmodified variable compression ratio (VCR) diesel engine for exploring the effect of biodiesel blends. The performance characteristics of Jatropha oil are compared with diesel fuel at two compression ratios 17 and 18. The viscosity and density are 23% and 3.9% higher with respect to diesel for pure jatropha methyl ester and calorific value is lower for J100, 6.8% with respect to diesel. Performance and emission have been observed better when compression ratio increases from 17 to 18 and also notice that the hydrocarbon (HC) and carban monoxide (CO) emission reduced but corban dioxide CO2 and NOX emission increases.
- 1 November 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 691 (1) , 012003
Open AccessPerformance characteristics of non-edible Jatropha oil with adjustable compression ratios
Non-edible biodiesel extracted from jatropha oil is broadly studied to solve the twin problem of reduction of fossil fuels and environmental degradation. The present study is conducted on unmodified variable compression ratio (VCR) diesel engine for exploring the effect of biodiesel blends. The performance characteristics of Jatropha oil are compared with diesel fuel at two compression ratios 17 and 18. The viscosity and density are 23% and 3.9% higher with respect to diesel for pure jatropha methyl ester and calorific value is lower for J100, 6.8% with respect to diesel. Performance and emission have been observed better when compression ratio increases from 17 to 18 and also notice that the hydrocarbon (HC) and carban monoxide (CO) emission reduced but corban dioxide CO2 and NOX emission increases.
- 1 January 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 18, 2984-2992
Modelling and optimization of EN 31 work material on wire electric discharge machining
- 1 January 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 18, 2984-2992
Modelling and optimization of EN 31 work material on wire electric discharge machining
- Open Access
- 21 March 2018
- Published by Springer Nature in Journal of Industrial Engineering International
- Vol. 14 (4) , 821-829
Optimisation of wire-cut EDM process parameter by Grey-based response surface methodology
- 21 March 2018
- Published by Springer Nature in Journal of Industrial Engineering International
- Vol. 14 (4) , 821-829
Open AccessOptimisation of wire-cut EDM process parameter by Grey-based response surface methodology