JLJinran Lin

Jinran Lin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jinran Lin has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization of Deposition Parameters for Ni-P-WC-BN(h) Composite Coatings via Orthogonal Experimentation and Wear Behavior of the Optimized Coating

    by Yingyue Li, Zehao Liu, Yana Li, Jinran Lin

    Ni–P–WC–BN(h) nanocomposite coatings were fabricated on 20CrMnTi substrates using ultrasonic-assisted pulsed electrodeposition. 20CrMnTi is a low-carbon steel that is commonly used in the manufacturing gears and shaft components. To enhance the wear resistance and extend the service life of such mechanical parts, ultrasonic-assisted pulsed electrodeposition was employed as an effective surface modification technique. The microhardness, phase structure, surface morphology, and wear behavior of the coating were also characterized. An orthogonal experimental design was employed to examine the effects of current density, bath temperature, ultrasonic power, and pulse duty cycle on the microhardness and wear behavior of the coatings, aiming to optimize the deposition parameters. The optimal process combination was identified as a current density of 3 A·dm−2, a bath temperature of 55 °C, an ultrasonic power of 210 W, and a duty cycle of 0.7. Under these conditions, the coatings exhibited enhanced hardness and wear resistance. Based on the optimized parameters, additional tribological tests were conducted under various operating conditions to further evaluate wear performance. The results showed that the dominant wear mechanisms were chemical wear and adhesive wear. This study offers new insights into the fabrication of high-performance nanocomposite coatings and expands the application scope of ultrasonic-assisted pulsed electrodeposition in multiphase composite systems.


  • Open Access

    Microstructure and Tribological Properties of Fe-Based-Al2O3-B4C Composite Coatings Prepared by High-Velocity Arc Spraying

    by Hao Li, Fang Huang, Jinran Lin, Min Kang, Joseph Ndiithi Ndumia, Jitao Liu

    Fe-based-Al2O3-B4C coating was prepared on the low-carbon steel substrates using high-velocity arc spraying. The effects of voltage, current, and distance on the porosity and microhardness of the coating were studied by an orthogonal test, and the optimum spraying parameters were determined. The microstructure and properties of Fe-based-Al2O3-B4C coatings prepared under optimum process parameters were characterized by X-ray diffractometer (XRD), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), microhardness and friction wear tester. The results showed that the optimum process parameters were a spraying voltage of 41 V, a spraying current of 200 A, and a spraying distance of 150 mm. The porosity was 2.24 ± 0.32%, and the microhardness was 1543 ± 145 Hv0.1, which was 8 times that of the substrate. Under the same load of 4.2 N and varying sliding speeds of 500 t/min, 750 t/min, and 1000 t/min, the coefficient of friction of the coating was less than that of the low-carbon steel, and the wear rate of the coating was 65%, 70%, and 63% lower than that of the low-carbon steel, respectively. The main wear mechanism of the coating was material spalling, accompanied by slight oxidative wear and abrasive wear.


  • Open Access

    Effects of Flow Velocity and Sand Concentration on Hydro-Abrasive Erosion Behavior of HVOF-Sprayed WC-Cr3C2-Ni Coating in 3.5 wt.% NaCl Aqueous Solution

    by Jinran Lin, Sheng Hong, Yuan Zheng, Wei Sun, Zhengwei Zhang, Min Kang, Xiuqing Fu

    To explore the hydro-abrasive erosion (HAE) behaviors of a high-velocity oxygen fuel (HVOF)-sprayed WC-Cr3C2-Ni coating in 3.5 wt.% NaCl aqueous solution, various flow velocities (FVs) and sand concentrations (SCs) were designed using a rotating disk rig facility. In comparison with 1Cr18Ni9Ti stainless steel, the WC-Cr3C2-Ni coating possessed higher hardness (H) and elastic modulus (E) values, worse anticorrosion properties, and superior HAE resistances in 3.5 wt.% NaCl aqueous solution. Higher FVs and SCs caused more severe HAE degradations for both the WC-Cr3C2-Ni coating and the 1Cr18Ni9Ti stainless steel, while FV had a greater influence on HAE resistances than SC. With an increase in the FV and SC, uncontinuous corrosion product films and erosion pits, the micro-cutting of the soft binder matrix and the fracturing of hard-phase grains, and crater formation and coating spalling were addressed as the HAE failure mechanisms in the 3.5 wt.% NaCl aqueous solution of the WC-Cr3C2-Ni coating.


  • Open Access

    Cavitation–Silt Erosion Behavior and Failure Mechanism of an HVOF-Sprayed WC-Cr3C2-Ni Coating for Offshore Hydraulic Machinery

    by Jinran Lin, Sheng Hong, Yuan Zheng, Wei Sun, Zhengwei Zhang, Min Kang, Xiuqing Fu

    WC-Cr3C2-Ni coatings are a vital class of hard ceramic/cermet coatings with potential applications as wear-resistant materials. However, their erosion wear behavior in 3.5 wt.% sodium chloride medium (SCM) remains largely unexplored. The present study investigated the cavitation–silt erosion (CSE) behavior in 3.5 wt.% SCM of WC-Cr3C2-Ni coatings sprayed with high-velocity oxygen–fuel (HVOF) under different flow velocities (FVs) and sand concentrations (SCs). Comparing the WC-Cr3C2-Ni coating with the 1Cr18Ni9Ti stainless steel, the first possessed superior CSE resistance in 3.5 wt.% SCM in a full range of FV and SC. Meanwhile, the coating appeared more influenced by FV and less influenced by SC, which was indicated by the fact that the amplification of VLR value (377.1%) when the FV ranged from 23.4 to 41.9 m·s−1 was larger than that (129.8%) when the SC increased from 10 kg·m−3 to 35 kg·m−3. With increasing FV and SC, the CSE process of the WC-Cr3C2-Ni coating in 3.5 wt.% SCM mainly included the discontinuous corrosion product films, erosion pits, fracturing of hard-phase grains, and micro-cutting of soft binder matrix, as well as crater formation and coating spalling.


  • Open Access

    Influence of Heat Treatment on the Microstructure and Wear Properties of Arc-Sprayed FeCrAl/Al Coating

    by Joseph Ndiithi Ndumia, Min Kang, Jinran Lin, Jitao Liu, Hao Li

    Intermetallic compounds formed during heat treatment of alloy coatings affect the coating structure and properties. In order to determine the phase changes and coating performance, FeCrAl (Fe Bal., Cr 26 wt.%, Al 6 wt.%) and Al (99.9 wt.%) coating was sprayed onto low carbon steel substrates and subsequently heat-treated at different temperatures. The effects of heat treatment on the microstructure, phase composition, tensile bonding strength, microhardness, and wear properties of the coatings were analyzed. The as-sprayed coating had a dense, layered structure with an average porosity of 3.6%. The microhardness of the as-sprayed coating was comprised of hard FeCrAl splats and ductile Al splats with an average microhardness value of 494 HV0.1. The coating at 300 °C had the highest tensile strength of 37.5 MPa. At 500 °C, FeAl intermetallic compounds formed at the phase boundaries due to the diffusion of elements. The coating microhardness and wear resistance were affected by the uniform coating structure and the precipitation of FeAl intermetallic compounds. Compared with the annealed coatings, the as-sprayed coating had the lowest wear rate.


  • Open Access

    A Review on the Wear, Corrosion and High-Temperature Resistant Properties of Wire Arc-Sprayed Fe-Based Coatings

    by Joseph Ndiithi Ndumia, Min Kang, Bertrand Vigninou Gbenontin, Jinran Lin, Samuel Mbugua Nyambura

    Among different thermal spraying methods, arc-spraying has been widely used due to its low operating costs and high deposition efficiency. The rapid progress of cored wire technology in arc-spraying has increased possibilities for the preparation of new Fe-based coating materials with enhanced properties by adding reinforcement particles and alloying elements to suit the different applications. Fe-based coatings have been extensively used because of their high strength, toughness, lower production costs, and availability of raw materials. This makes them suitable replacements for Ni-based coatings in ambient and high-temperature applications. This review discusses the research status and developments of the arc-sprayed Fe-based coatings. The study specifically reviews the wear behavior, corrosion analysis, and high-temperature resistant properties of arc-sprayed Fe-based coatings, aiming to develop an understanding of the protection mechanisms for Fe-based coatings. The performance of the Fe-based coatings depends on the integrity of the coating structure. Optimizing arc-spraying parameters minimizes defects (pores, grain boundaries, unmelted particles, oxides, and microcracks) that deteriorate the coating properties. High amorphous phase content, ceramic reinforcement particles and alloying elements enhance the corrosion, tribological, and high-temperature resistant properties of Fe-based coatings. In high-temperature applications, Fe-based coatings form oxide scales that protect the coating from further oxidation; thus, it is important to select the optimum composition for the alloying elements.


  • Open Access

    Influence of Element Penetration Region on Adhesion and Corrosion Performance of Ni-Base Coatings

    by Xiuqing Fu, Zhenyu Shen, Xinxin Chen, Jinran Lin, Hongbing Cao

    In this study, Ni–P/Ni–P–SiC coatings were prepared on pretreated 45 steel substrates by scanning electrodeposition. Prior to the electrodeposition, the substrates were subjected to two types of pretreatments: polishing and sandblasting. The 3D morphology of the pretreated substrates was characterized by laser scanning confocal microscopy. The micromorphology and section morphology of the coating surface were characterized by field emission scanning electron microscopy. The section element composition was characterized using an EDS energy spectrum analyzer. The adhesion and corrosion resistance of 15 coatings were analyzed using an automatic scratch tester and CS350 electrochemical workstation. The results showed the presence of an element penetration region between the coating and the substrate. The sandblasting pretreatment and SiC nanoparticle addition helped widen the penetration region of the elements. The Ni–P–SiC coating prepared by scanning electrodeposition on the sandblasted substrate exhibited the thickest penetration region, up to 28.39 µm. A scratch test conducted on this coating showed that it exhibits the best adhesion force, up to 36.5 N. In electrochemical corrosion experiments, its corrosion potential was found to be the highest, reaching −0.30 V, and the corrosion current density was the lowest, reaching 8.45 × 10−7 A·cm−2. The presence of the element penetration region increased the coating adhesion and improved the corrosion resistance.


  • Open Access

    Effect of Current Density on the Performance of Ni–P–ZrO2–CeO2 Composite Coatings Prepared by Jet-Electrodeposition

    by Zhaoyang Song, Hongwen Zhang, Xiuqing Fu, Jinran Lin, Moqi Shen, Qingqing Wang, Shuanglu Duan

    The objective of this study was to improve the surface properties, hardness, wear resistance and electrochemical corrosion resistance of #45 steel. To this end, Ni–P–ZrO2–CeO2 composite coatings were prepared on the surface of #45 steel using the jet-electrodeposition technique by varying the current density from 20 to 60 A/dm2. The effect of current density on the performance of the composite coatings was evaluated. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) were applied to explore the surface topography, elemental composition, hardness and electrochemical corrosion resistance of the composite coatings. The results showed that with the increase in the current density, the hardness, wear resistance, and electrochemical corrosion resistance tends to increase first and then decrease. At a current density of 40 A/dm2, the hardness reached a maximum of 688.9 HV0.1, the corrosion current reached a minimum of 8.2501 × 10−5 A·cm−2, and the corrosion potential reached a maximum of −0.45957 V. At these values, the performance of the composite coatings was optimal.


  • Open Access

    Improvement in Tribological Properties of Cr12MoV Cold Work Die Steel by HVOF Sprayed WC-CoCr Cermet Coatings

    by Sheng Hong, Yuping Wu, Bo Wang, Jinran Lin

    The main objective of this study was to develop an efficient coating to increase the wear resistance of cold work die steel at different temperatures. The microstructures of high-velocity oxygen-fuel (HVOF)-sprayed WC-CoCr coatings were evaluated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The effect of temperature on the tribological properties of the coatings and the reference Cr12MoV cold work die steel were both investigated by SEM, environmental scanning electron microscopy (ESEM), X-ray diffraction (XRD), and a pin-on-disk high-temperature tribometer. The coating exhibited a significantly lower wear rate and superior resistance against sliding wear as compared to the die steel at each test temperature, whereas no major differences in terms of the variation tendency of the friction coefficient as a function of temperature were observed in both the coatings and the die steels. These can be attributed to the presence of nanocrystalline grains and the fcc-Co phase in the coating. Moreover, the wear mechanisms of the coatings and the die steels were compared and discussed. The coating presented herein provided a competitive approach to improve the sliding wear performance of cold work die steel.