AUAlena Uhnáková

Alena Uhnáková

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Alena Uhnáková has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Size effects in molecular dynamic simulations of fracture in bcc iron crystals

    by Petr Pařík, Anna Machová, Jan Červ, Alena Uhnáková, Petr Hora

    Three-dimensional (3D) simulations via molecular dynamics (MD) show that the brittle or ductile behavior of the atomistic samples with the edge crack (001)[110] (crack plane/crack front) depend on size of the self-similar atomistic crystals. Since the basic continuum predictions concerning cracks do not consider the random thermal atomic motion, we are restricted in this study to MD simulations with initial temperature of 0 K. For all samples tested, the crack initiation is brittle. However, the subsequent crack growth can be inhibited by twin formation on oblique planes {112}, crack branching along {011} planes and new dislocation emissions on {123} slip planes and the final fracture can also be then ductile, which depends predominantly on the thickness of the atomistic sample. The representative quantity, the atomistic fracture toughness initially increases with increasing sample thickness and later saturates near Griffith level for plane strain state along the crack front. The tested loading rates are equivalent to a cross head speed of 0.833 · 10−4 m s−1 used in one our previous experiment. These new MD results comply with the stress analysis performed by the anisotropic linear fracture mechanics (LFM) and with some experimental observations.


  • Fracture toughness of Fe–Si single crystals in mode I: Effect of loading rate on an edge crack (–110)[110] at macroscopic and atomistic level

    by Alena Uhnáková, Anna Machová, Michaela Janovská, Martin Ševčík, Jan Štefan, Petr Hora, Jaroslav Čapek, Pavel Lejček

    This paper is devoted to an experimental and 3D atomistic study of the influence of loading rate on fracture toughness in dilute Fe–Si alloys and in bcc iron. We analyze new and previous experimental results from fracture tests performed at room temperature on bcc iron–silicon single crystals with edge cracks (1¯10) [110] (crack plane/crack front). The specimens of single edge notch-type were loaded in tension mode I under different loading rates. The ductile–brittle behavior at the crack front was monitored online via optical microscopy together with external force and prolongation of the specimens. About 30% decrease in fracture toughness was monitored in the new experiment under the highest loading rate. The nanoscopic processes produced by the crack itself were studied at room temperature via 3D molecular dynamics (MD) simulations in bcc iron under equivalent boundary conditions as in experiments to reveal (explain) the sensitivity of the crack to loading rate. For this purpose, this MD study utilizes the self-similar character of linear fracture mechanics. The results show that the emission of blunting dislocations from the crack is the most difficult under the highest loading rate, which leads to the reduced fracture toughness of the atomistic sample. This is in a qualitative agreement with the experimental (macro) results. Moreover, MD indicates that there may be some synergetic (resonant) effect between the loading rate and thermal activation that promotes dislocation emission.


  • Open Access

    Ductile-brittle transition at edge cracks (001)[110] in BCC iron under different loading rates in mode I: a 3D atomistic study

    by Alena Uhnáková, Anna Machová, Jan Červ, Petr Hora, Jaroslav Joch

    3D atomistic simulations via molecular dynamics (MD) at temperature of 0 K and 295 K (22 °C) with a high quasi-static loading rate dP/dt of 2.92 kN s−1 show that cleavage fracture is supported by surface emission of oblique dislocations 11 1 ¯ 011 and by their subsequent cross slip to {112} planes, which increases separation of the (001) cleavage planes inside the crystal. Under the slower loading rate by a factor 5, the crack growth is hindered by twin generation on oblique planes {112} and the fracture is ductile. The MD results explain the contribution of the crack itself to the ductile-brittle transition observed in our fracture experiments on Fe-3wt%Si single crystals of the same orientation and geometry, loaded at the same rates dP/dt as in MD. The loading rates are equivalent to the cross head speed of 5 mm min−1 and 1 mm min−1 used in the experiment. The MD results also agree with the stress analysis performed by the anisotropic LFM and comply with experimental observations.


  • Open Access

    Thermal Activation and Ductile vs. Brittle Behavior of Microcracks in 3D BCC Iron Crystals under Biaxial Loading by Atomistic Simulations

    by Alena Uhnáková, Anna Machová, Petr Hora

    We present the results of free 3D molecular dynamics (MD) simulations, focused on the influence of temperature on the ductile-brittle behavior of a pre-existing central Griffith through microcrack (1¯10)[110] (crack plane/crack front) under biaxial loading σA and σB in tension mode I. At temperatures of 300 K and 600 K, the MD results provide new information on the threshold values of the stress intensity factor K and the energy release rate G, needed for the emission of {112} blunting dislocations that support crack stability. A simple procedure for the evaluation of thermal activation from MD results is proposed in the paper. 3D atomistic results are compared with continuum predictions on thermal activation of the crack induced dislocation generation. At elevated temperature T and biaxiality ratios σB/σA ≤ 0.8 dislocation emission in MD is observed, supported by thermal activation energy of about ~30 kBT. With increasing temperature, the ductile-brittle transition moves to a higher biaxiality ratios in comparison with the situation at temperature of ~0 K. Near the transition, dislocation emission occurs at lower loadings than expected by continuum predictions. For the ratios σB/σA ≥ 1, the elevated temperature facilitates (surprisingly) the microcrack growth below Griffith level.


  • Dislocation emission and crack growth in 3D bcc iron crystals under biaxial loading by atomistic simulations

    by Alena Uhnáková, Anna Machová, Petr Hora

    This paper is devoted to the study of the ductile-brittle behavior of a central nanocrack ( 1 ¯ 10 ) [ 110 ] (crack plane/crack front) under biaxial loading via free 3D molecular dynamics (MD) simulations, as well as the comparison of MD results with continuum predictions concerning T-stress. The so called T-stress is a constant stress component acting along the crack plane, which should be considered (together with the stress intensity factor K) in the assessment of brittle-ductile behavior, namely, in the case of the short cracks. Previous 2D atomistic simulations under plane strain conditions indicated that the level of T-stress (controlled by the biaxiality ratio σB/σA from the external loading) affects dislocation emission from the crack and can cause the ductile-brittle transition. The plane strain simulations using the periodic or translational boundary conditions in the bcc lattice have certain limitations: they enable the in-plane dislocation emission (Burgers vector lies in the observation plane), but they do not allow the complete dislocation emission on the all slip systems favored by the shear stress. As presented, our new free 3D atomistic simulations (without periodic or symmetry conditions) enable the activity of the all favored slip systems. Thus, they offer a more realistic insight into the microscopic processes generated by the crack itself in dependence on the T-stress level.