Prashant Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Prashant Sharma has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Manoj Kumar
Department of Physics, Malaviya National Institute of Technology Jaipur, Jaipur, India
2 shared publications Ravindra Mukhiya
CSIR-Central Electronics Engineering Research Institute (CEERI), Pilani, India
2 shared publicationsRishi Sharma
CSIR-Central Electronics Engineering Research Institute (CEERI), Pilani, India
2 shared publications- Amit Kumar
CSIR-Central Electronics Engineering Research Institute
1 shared publication - Deepak Bansal
CSIR-Central Electronics Engineering Research Institute
1 shared publication Kamlendra Awasthi
Department of Physics, Malaviya National Institute of Technology, Jaipur, India
1 shared publication
Latest Publications
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 39 (1) , 28-35
Buckling and Stress-Controlled RF MEMS Structures Using Annealing
Micro-Electro-Mechanical System (MEMS) devices show better performance as compared to solid-state devices in terms of radio frequency (RF) response, like insertion loss and isolation. However, MEMS devices face reliability issues, and stress is one of the main concerns. MEMS devices involve many non-traditional fabrication steps, like releasing hanging structures. Released MEMS structures show built-in stress from the fabrication process. This stress can cause them to bend, curl, or buckle. Especially in the case of Radio Frequency (RF) MEMS switches, curling buckling increases the pull-in voltage. In the literature, to address stress-related buckling, thermal annealing was applied at different temperatures after release. However, post-release annealing reduces the stress and results in curled-up and unstable structures. The present paper explores a novel and innovative method for thermally annealing structures at an appropriate stage to reduce stress and buckling in released cantilever structures. Annealing at the appropriate step results in a significant reduction in cantilever bending and warping, indicating effective stress relaxation and yielding straight, mechanically stable cantilevers. After controlling the stress and buckling, the pull-in voltage is reduced to 40 V, which is in close agreement with the simulated results. The measured insertion loss of the switch is -0.4 dB, and isolation is -22 dB for the DC to 20 GHz frequency range.
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 39 (1) , 28-35
Buckling and Stress-Controlled RF MEMS Structures Using Annealing
Micro-Electro-Mechanical System (MEMS) devices show better performance as compared to solid-state devices in terms of radio frequency (RF) response, like insertion loss and isolation. However, MEMS devices face reliability issues, and stress is one of the main concerns. MEMS devices involve many non-traditional fabrication steps, like releasing hanging structures. Released MEMS structures show built-in stress from the fabrication process. This stress can cause them to bend, curl, or buckle. Especially in the case of Radio Frequency (RF) MEMS switches, curling buckling increases the pull-in voltage. In the literature, to address stress-related buckling, thermal annealing was applied at different temperatures after release. However, post-release annealing reduces the stress and results in curled-up and unstable structures. The present paper explores a novel and innovative method for thermally annealing structures at an appropriate stage to reduce stress and buckling in released cantilever structures. Annealing at the appropriate step results in a significant reduction in cantilever bending and warping, indicating effective stress relaxation and yielding straight, mechanically stable cantilevers. After controlling the stress and buckling, the pull-in voltage is reduced to 40 V, which is in close agreement with the simulated results. The measured insertion loss of the switch is -0.4 dB, and isolation is -22 dB for the DC to 20 GHz frequency range.
- 9 March 2022
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 51 (5) , 2673-2681
Bismuth Oxide Extended-Gate Field-Effect Transistor as pH Sensor
- 9 March 2022
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 51 (5) , 2673-2681
Bismuth Oxide Extended-Gate Field-Effect Transistor as pH Sensor
- 19 March 2020
- Published by Springer Nature in Applied Physics A
- Vol. 126 (4) , 1-7
Development of ZnO nanostructure film for pH sensing application
- 19 March 2020
- Published by Springer Nature in Applied Physics A
- Vol. 126 (4) , 1-7
Development of ZnO nanostructure film for pH sensing application