Vladimir Yu. Savin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vladimir Yu. Savin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Viktor V. Nikitin
Bryansk State Agrarian University
4 shared publications - Виктор Николаевич Ожерельев
Брянский государственный аграрный университет
4 shared publications Bryansk State Agrarian University
1 shared publication- Ivan P. Adylin
Bryansk State Agrarian University
1 shared publication Kaluga branch of Moscow State Technical University named after N.E. Bauman
1 shared publication- Natalia V. Sinyaya
Bryansk State Agrarian University
1 shared publication
Latest Publications
- Open Access
- 22 December 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (4) , 641-657
Experimental Study of the Process of Preliminary Separation of Light Impurities from Combed Heap
Introduction. There are specified and considered the trends determining the directionsfor the development of grain harvesting equipment. One of the most important issues is increasing the productivity of a grain harvester while maintaining its acceptable metalcontent and energy consumption. Traditional solutions have largely exhausted themselves, so a promising solution is the use of the technology for combing of standing plants.Aim of the Study. The study is aimed at determining the proportion of light impuritiesseparated from the grain heap depending on the height of the combing header outlet.Materials and Methods. There was used an experimental method to examine a combingheader with preliminary separation of light impurities. During the experiment, the height of the stripper header outlet was varied. The mass of the separated chaff and its composition were determined. When processing the experimental data, there were obtained relationships meeting the study objectives. The results are divided into two groups: the results with the use of solid shields installed on the combing header rear wall and those without solid shields, when the rear wall is a mesh surface.Results. There has been developed a method for determining the proportion of separated light impurities. There have been found the dependences of the proportion of separated light impurities and the proportion of lost grain on the combing header outlet height. There has been identified an optimal range of the combing header outlet height if the solid shields removed from the combing header rear wall. If the range of combing header outlet height is from 124 to 130 mm, the proportion of separated light impurities reaches 13%, while grain losses remain relatively low.Discussion and Conclusion. In the context of separating the heap light impurities, there has been obtained a significant result, which allows not only unloading significantly the grain harvester cleaning system and increasing its productivity, but also improving the efficiency of separating grain on the pre-drum separating device or directly on the grate bottom of the inclined chamber.
- 22 December 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (4) , 641-657
Open AccessExperimental Study of the Process of Preliminary Separation of Light Impurities from Combed Heap
Introduction. There are specified and considered the trends determining the directionsfor the development of grain harvesting equipment. One of the most important issues is increasing the productivity of a grain harvester while maintaining its acceptable metalcontent and energy consumption. Traditional solutions have largely exhausted themselves, so a promising solution is the use of the technology for combing of standing plants.Aim of the Study. The study is aimed at determining the proportion of light impuritiesseparated from the grain heap depending on the height of the combing header outlet.Materials and Methods. There was used an experimental method to examine a combingheader with preliminary separation of light impurities. During the experiment, the height of the stripper header outlet was varied. The mass of the separated chaff and its composition were determined. When processing the experimental data, there were obtained relationships meeting the study objectives. The results are divided into two groups: the results with the use of solid shields installed on the combing header rear wall and those without solid shields, when the rear wall is a mesh surface.Results. There has been developed a method for determining the proportion of separated light impurities. There have been found the dependences of the proportion of separated light impurities and the proportion of lost grain on the combing header outlet height. There has been identified an optimal range of the combing header outlet height if the solid shields removed from the combing header rear wall. If the range of combing header outlet height is from 124 to 130 mm, the proportion of separated light impurities reaches 13%, while grain losses remain relatively low.Discussion and Conclusion. In the context of separating the heap light impurities, there has been obtained a significant result, which allows not only unloading significantly the grain harvester cleaning system and increasing its productivity, but also improving the efficiency of separating grain on the pre-drum separating device or directly on the grate bottom of the inclined chamber.
- Open Access
- 6 December 2024
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 91 (5) , 553-561
The influence of the composition of the combed grain heap on the preliminary separation of loose grain
BACKGROUND: The paper reviews the state of the problem of grain harvesting by the method of combing plants on the root. Attention is focused on the potential economic efficiency of the method and on the scientific and technological problems hindering its widespread implementation. In particular, in order to reduce the degree of crushing of loose grain, it is necessary to separate it preliminary and prevent it from entering the threshing device. It is proposed to remove grain directly on the lattice bottom of the inclined chamber of the combine harvester. The scientific hypothesis of the study suggests that in order to improve separation, it is advisable to remove a significant part of light impurities from the pile directly preliminary in the body of the combing adapter. AIM: Evaluation of the efficiency of separation of loose grain by removing a significant part of light impurities from the combed pile before it enters the inclined chamber. METHODS: To confirm the hypothesis, the experiment was conducted in which a combed grain pile of wheat of the «Moskovskaya 56» variety of different component composition was fed to a lattice surface equipped with a scraper conveyor. The weight content of the grain varied from 70 to 100%. The experiment took into account the proportion of loose grain that passed through the holes of the grate at its length of 920 mm and the width of the holes of 12 mm. It ranged from 65 to 80% as the content of loose grain in the pile increased. RESULTS: According to the study results, it was found that the passage of loose grain through the openings of the lattice bottom varies between 65-80%. At the same time, a decrease in the mass fraction of loose grain in the pile reduces its passage through the openings of the lattice surface by 15%. CONCLUSION: Preliminary removal of light impurities from the combed grain pile, comparable in size to loose grain, can be carried out by using an inertial separation system. Reducing the proportion of light impurities in the pile entering the combine harvester cleaning system makes it possible to significantly increase the efficiency of its operation.
- 6 December 2024
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 91 (5) , 553-561
Open AccessThe influence of the composition of the combed grain heap on the preliminary separation of loose grain
BACKGROUND: The paper reviews the state of the problem of grain harvesting by the method of combing plants on the root. Attention is focused on the potential economic efficiency of the method and on the scientific and technological problems hindering its widespread implementation. In particular, in order to reduce the degree of crushing of loose grain, it is necessary to separate it preliminary and prevent it from entering the threshing device. It is proposed to remove grain directly on the lattice bottom of the inclined chamber of the combine harvester. The scientific hypothesis of the study suggests that in order to improve separation, it is advisable to remove a significant part of light impurities from the pile directly preliminary in the body of the combing adapter. AIM: Evaluation of the efficiency of separation of loose grain by removing a significant part of light impurities from the combed pile before it enters the inclined chamber. METHODS: To confirm the hypothesis, the experiment was conducted in which a combed grain pile of wheat of the «Moskovskaya 56» variety of different component composition was fed to a lattice surface equipped with a scraper conveyor. The weight content of the grain varied from 70 to 100%. The experiment took into account the proportion of loose grain that passed through the holes of the grate at its length of 920 mm and the width of the holes of 12 mm. It ranged from 65 to 80% as the content of loose grain in the pile increased. RESULTS: According to the study results, it was found that the passage of loose grain through the openings of the lattice bottom varies between 65-80%. At the same time, a decrease in the mass fraction of loose grain in the pile reduces its passage through the openings of the lattice surface by 15%. CONCLUSION: Preliminary removal of light impurities from the combed grain pile, comparable in size to loose grain, can be carried out by using an inertial separation system. Reducing the proportion of light impurities in the pile entering the combine harvester cleaning system makes it possible to significantly increase the efficiency of its operation.
- Open Access
- 24 September 2024
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 34 (3) , 370-387
Separating Light Impurities from the Combed Heap in the Adapter Case
Introduction. It is possible to increase the separating of loose grain on the lattice bottom of the combine harvester feeder house by removing most of the light impurities from the combed heap using an inertial cleaning system built into the combing adapter body.Aim of the Study. The study is aimed at developing an inertial system for separating light impurities in the combing header body and optimizing its main parameters.Materials and Methods. The object of the study was a large-scale model of a pneumatic cleaning device to simulate the motion of air and components of a combed grain heap inside the combing adapter body. It was a two-factor experiment with three variations of the air flow velocity (4.5; 5.5; 6.5 m/s) and the width of the air channel (0.26; 0.29; 0.32 m). The studies were conducted on a combed heap of Moskovskaya 56 wheat with a moisture content of about 12%. As a parameter for optimization and response function, a portion of the combed heap was selected from the body of the installation with an air flow.Results. According to the results of the experimental studies, it was found that the air flow velocity has a greater effect on separating glumes than the width of the air channel. A simultaneous increase in both factors leads to an improved separation. At the same time, if increasing the air flow velocity ensures a stable increase in the proportion of the combed heap and is limited only by the air velocity at which grain appears in the combed heap along with the glumes, then changing the channel width allows achieving the parameter optimal value.Discussion and Conclusions. The use of an inertial cleaning system makes it possible to remove almost completely light impurities from the combed heap. The optimal parameters of the device are: channel width 0.28...0.3 m, air flow velocity 6...6.5 m/s.
- 24 September 2024
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 34 (3) , 370-387
Open AccessSeparating Light Impurities from the Combed Heap in the Adapter Case
Introduction. It is possible to increase the separating of loose grain on the lattice bottom of the combine harvester feeder house by removing most of the light impurities from the combed heap using an inertial cleaning system built into the combing adapter body.Aim of the Study. The study is aimed at developing an inertial system for separating light impurities in the combing header body and optimizing its main parameters.Materials and Methods. The object of the study was a large-scale model of a pneumatic cleaning device to simulate the motion of air and components of a combed grain heap inside the combing adapter body. It was a two-factor experiment with three variations of the air flow velocity (4.5; 5.5; 6.5 m/s) and the width of the air channel (0.26; 0.29; 0.32 m). The studies were conducted on a combed heap of Moskovskaya 56 wheat with a moisture content of about 12%. As a parameter for optimization and response function, a portion of the combed heap was selected from the body of the installation with an air flow.Results. According to the results of the experimental studies, it was found that the air flow velocity has a greater effect on separating glumes than the width of the air channel. A simultaneous increase in both factors leads to an improved separation. At the same time, if increasing the air flow velocity ensures a stable increase in the proportion of the combed heap and is limited only by the air velocity at which grain appears in the combed heap along with the glumes, then changing the channel width allows achieving the parameter optimal value.Discussion and Conclusions. The use of an inertial cleaning system makes it possible to remove almost completely light impurities from the combed heap. The optimal parameters of the device are: channel width 0.28...0.3 m, air flow velocity 6...6.5 m/s.
- 27 April 2024
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 2
INFLUENCE OF THE COMPOSITION OF COLLECTED GRAIN HEAP ON THE EFFICIENCY OF ITS SEPARATION ON A GRID SURFACE
The separating ability of the lattice surface when working with combed grain heaps of various fractional compositions was studied. The scientific hypothesis of the study is the assumption that with an increase in the mass fraction of chaff in the heap, the separation efficiency should decrease due to an increase in the volume of grain with a constant mass of the sample of the heap under study as the grain content decreases due to the larger volumetric mass of the latter compared to the chaff. It is a legitimate assumption that the passage of a larger volume of heap through the holes of the lattice surface requires more time, that is, the separation rate should decrease. Experimental studies were carried out on a combed grain heap of wheat variety Moskovskaya 56 with a relative humidity of 12%. The mass fraction of grain in the heap varied from 100 to 60% in increments of 10%. The experimental installation was made on the basis of the grain elevator of the KZS 1218 combine harvester, in which, instead of the dismantled lower wall, a lattice surface with longitudinal holes 900 mm long and 12 mm wide was installed. The installation simulated the operation of the inclined chamber of a combine harvester, the lattice bottom of which should separate free grain from the combed heap and direct it for cleaning, bypassing the threshing apparatus. In this regard, the speed of the scraper conveyor was 3 m/s. The heap that passed through the holes in the lattice was caught, after which it was disassembled into fractions and accounted for. As a result of the experiment, it was established that as the mass fraction of grain in the heap decreases, the separation rate of the latter within the zone of variation of the initial parameter decreases by 4%. Therefore, it is advisable to first remove a significant portion of light impurities from the combed heap before it enters the inclined chamber.
- 27 April 2024
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 2
INFLUENCE OF THE COMPOSITION OF COLLECTED GRAIN HEAP ON THE EFFICIENCY OF ITS SEPARATION ON A GRID SURFACE
The separating ability of the lattice surface when working with combed grain heaps of various fractional compositions was studied. The scientific hypothesis of the study is the assumption that with an increase in the mass fraction of chaff in the heap, the separation efficiency should decrease due to an increase in the volume of grain with a constant mass of the sample of the heap under study as the grain content decreases due to the larger volumetric mass of the latter compared to the chaff. It is a legitimate assumption that the passage of a larger volume of heap through the holes of the lattice surface requires more time, that is, the separation rate should decrease. Experimental studies were carried out on a combed grain heap of wheat variety Moskovskaya 56 with a relative humidity of 12%. The mass fraction of grain in the heap varied from 100 to 60% in increments of 10%. The experimental installation was made on the basis of the grain elevator of the KZS 1218 combine harvester, in which, instead of the dismantled lower wall, a lattice surface with longitudinal holes 900 mm long and 12 mm wide was installed. The installation simulated the operation of the inclined chamber of a combine harvester, the lattice bottom of which should separate free grain from the combed heap and direct it for cleaning, bypassing the threshing apparatus. In this regard, the speed of the scraper conveyor was 3 m/s. The heap that passed through the holes in the lattice was caught, after which it was disassembled into fractions and accounted for. As a result of the experiment, it was established that as the mass fraction of grain in the heap decreases, the separation rate of the latter within the zone of variation of the initial parameter decreases by 4%. Therefore, it is advisable to first remove a significant portion of light impurities from the combed heap before it enters the inclined chamber.
- Open Access
- 30 September 2021
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 31 (3) , 403-413
Study of a Stripper Header for Grain Harvesting as a Vibrating System
Grain losses caused by stripping defects are the main problem to be solved in designing a stripper header. To reduce these losses, a design of a stripper header with a vibration drive is proposed. This device combines the processes of stripping grain crops and the vibration effect of the stripping fingers upon the ears of plants. The most important stage of the mathematical description of these processes is composing the differential equation of the stripping fingers motion.
- 30 September 2021
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 31 (3) , 403-413
Open AccessStudy of a Stripper Header for Grain Harvesting as a Vibrating System
Grain losses caused by stripping defects are the main problem to be solved in designing a stripper header. To reduce these losses, a design of a stripper header with a vibration drive is proposed. This device combines the processes of stripping grain crops and the vibration effect of the stripping fingers upon the ears of plants. The most important stage of the mathematical description of these processes is composing the differential equation of the stripping fingers motion.
- Open Access
- 30 September 2020
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 30 (3) , 413-425
Determination of the Friction Angle between the Wheat Ear and Stripper Fingers
Introduction. Determining the angle of friction between stripper fingers and a wheat ear is an important task aimed at finding the optimal design parameters and operating modes of stripping devices. When stripper fingers and wheat ears interact, the relative position of the ear glumes, flower glumes, and grains is densified. In this case, the spikelet surface roughness changes. Materials and Methods. A series of experiments was carried out to determine the angles of friction between a steel stripper fingers and wheat ears. Wheat varieties “Moskovskaya 40” and “Moskovskaya 56” were selected for the study. The experimental measuring installation is a frame with a rotatable platform mounted on it with the adjustable angle of rotation. The goniometer head provides the ability to fix the platform rotation angle value. The weight suspended from the stem of the plant imitated the forces arising in the process of stripping. The width and thickness of the wheat ear were also measured and recorded. Results. The influence of the size of the wheat ear on the angle of friction is determined. The results of the study are divided into two groups. The following values of the friction angles were obtained: 26.4–31.5° for the wheat with ear width of less than 10.4 mm; 22.0–27.1° for the wheat with ear width of more than 10.4 mm. Discussion and Conclusion. The angles of friction of wheat ears on the stripper fingers for wheat varieties specific to the Central region are obtained. The dependence of the angle of friction on the ratio of the geometric dimensions of the wheat ear and the slit width of the stripper fingers is established. When a wheat ear width is less than 10.4 mm, an effect of pinching the spikelets between the stripper fingers was observed. In this case, the coefficient of friction noticeably increased.
- 30 September 2020
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 30 (3) , 413-425
Open AccessDetermination of the Friction Angle between the Wheat Ear and Stripper Fingers
Introduction. Determining the angle of friction between stripper fingers and a wheat ear is an important task aimed at finding the optimal design parameters and operating modes of stripping devices. When stripper fingers and wheat ears interact, the relative position of the ear glumes, flower glumes, and grains is densified. In this case, the spikelet surface roughness changes. Materials and Methods. A series of experiments was carried out to determine the angles of friction between a steel stripper fingers and wheat ears. Wheat varieties “Moskovskaya 40” and “Moskovskaya 56” were selected for the study. The experimental measuring installation is a frame with a rotatable platform mounted on it with the adjustable angle of rotation. The goniometer head provides the ability to fix the platform rotation angle value. The weight suspended from the stem of the plant imitated the forces arising in the process of stripping. The width and thickness of the wheat ear were also measured and recorded. Results. The influence of the size of the wheat ear on the angle of friction is determined. The results of the study are divided into two groups. The following values of the friction angles were obtained: 26.4–31.5° for the wheat with ear width of less than 10.4 mm; 22.0–27.1° for the wheat with ear width of more than 10.4 mm. Discussion and Conclusion. The angles of friction of wheat ears on the stripper fingers for wheat varieties specific to the Central region are obtained. The dependence of the angle of friction on the ratio of the geometric dimensions of the wheat ear and the slit width of the stripper fingers is established. When a wheat ear width is less than 10.4 mm, an effect of pinching the spikelets between the stripper fingers was observed. In this case, the coefficient of friction noticeably increased.
- Open Access
- 21 April 2020
- Published by FSB Educational Establishment of Higher Education Daghestan State Technical University in Herald of Dagestan State Technical University. Technical Sciences
- Vol. 47 (1) , 39-47-47
STUDY OF TORQUE NONUNIFORMITY IN DOUBLE-ACTION HYDRAULIC ROTARY VANE MO-TORS
Abstract. Aim. Hydraulic rotary vane motors rely on the principle of torque maintained at a nominal pressure. In this case, the most important parameter of the torque is its nonuniformity. The problem of determining nonuniform torque in hydraulic motors having ten and twelve vanes is investigated with the aim of ensuring the maximum stability of this parameter.Method. Braking torque occurs on the vanes of hydraulic rotary vane motors due to the pressure of the working fluid on the stator; the theoretical expression for torque does not take the braking effect of the vanes into account. Therefore, an expression is compiled for the braking torque of the vanes with a type of stator curve that provides constant acceleration of the vane relative to the rotor.Results. Plots of changes in braking torques were constructed for 10- and 12-vane motors. Ratios of the minimum and maximum braking torques equal to 0.33 and 0.5 for motors with ten and twelve vanes, respectively, were obtained.Conclusion. The torque nonuniformity coefficients for hydraulic motors for the given parameters of d =11,6% and d = 8,8% for motors having ten and twelve vanes, respectively, were obtained. The results of the analysis of the obtained parameters indicate a slight increase in the nonuniformity of torque in a ten-vane motor. In this case, a decrease in the number of vanes leads to an increase in the mechanical efficiency of the hydraulic machine.
- 21 April 2020
- Published by FSB Educational Establishment of Higher Education Daghestan State Technical University in Herald of Dagestan State Technical University. Technical Sciences
- Vol. 47 (1) , 39-47-47
Open AccessSTUDY OF TORQUE NONUNIFORMITY IN DOUBLE-ACTION HYDRAULIC ROTARY VANE MO-TORS
Abstract. Aim. Hydraulic rotary vane motors rely on the principle of torque maintained at a nominal pressure. In this case, the most important parameter of the torque is its nonuniformity. The problem of determining nonuniform torque in hydraulic motors having ten and twelve vanes is investigated with the aim of ensuring the maximum stability of this parameter.Method. Braking torque occurs on the vanes of hydraulic rotary vane motors due to the pressure of the working fluid on the stator; the theoretical expression for torque does not take the braking effect of the vanes into account. Therefore, an expression is compiled for the braking torque of the vanes with a type of stator curve that provides constant acceleration of the vane relative to the rotor.Results. Plots of changes in braking torques were constructed for 10- and 12-vane motors. Ratios of the minimum and maximum braking torques equal to 0.33 and 0.5 for motors with ten and twelve vanes, respectively, were obtained.Conclusion. The torque nonuniformity coefficients for hydraulic motors for the given parameters of d =11,6% and d = 8,8% for motors having ten and twelve vanes, respectively, were obtained. The results of the analysis of the obtained parameters indicate a slight increase in the nonuniformity of torque in a ten-vane motor. In this case, a decrease in the number of vanes leads to an increase in the mechanical efficiency of the hydraulic machine.
- Open Access
- 30 September 2019
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 29 (3) , 456-466
Determination of the Force Required for Stripping the Wheat Ear
Introduction. The force required for stripping the ear is one of important parameters characterizing the process of stripping. The force varies within certain limits depending on the type of plant, grain moisture, and structural and morphological parameters of the ear. A series of experiments was carried out to determine forces of different types of wheat stripping. Materials and Methods.Experimental studies were carried out in the Kaluga Oblast in the fields of Kaluga Research Institute of Agriculture. The study dealt with wheat varieties “Kasar”, “Moskovskaya 56”, and “Moskovskaya 40”. Ear parameters were estimated directly before testing as structural and morphological parameters of the ear can change significantly depending on growing conditions. It was suggested that such parameters as the width and thickness of the ear affect the process of the latter interaction with stripping fingers. Results. Forces of stripping the said wheat varieties were obtained using stripping fingers with a gap of 5–7 mm. Stripping forces of the “Kasar” wheat varied from 17,4 to 24,2 N, under conditions of the gap of 6 mm, and from 13,4 to 16,8, with the gap of 7 mm. Discussion and Conclusion. Dependence of the stripping force on the gap width of stripping fingers was confirmed by results of our experiments. Forces varied in the range of 16,5–20,6 N when stripping off “Moskovskaya 40” wheat in the case of the gap of 5 mm and 8,1–14 N in the case of the 7-mm gap. The effect of such ear parameters as the width, thickness and density was established.
- 30 September 2019
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 29 (3) , 456-466
Open AccessDetermination of the Force Required for Stripping the Wheat Ear
Introduction. The force required for stripping the ear is one of important parameters characterizing the process of stripping. The force varies within certain limits depending on the type of plant, grain moisture, and structural and morphological parameters of the ear. A series of experiments was carried out to determine forces of different types of wheat stripping. Materials and Methods.Experimental studies were carried out in the Kaluga Oblast in the fields of Kaluga Research Institute of Agriculture. The study dealt with wheat varieties “Kasar”, “Moskovskaya 56”, and “Moskovskaya 40”. Ear parameters were estimated directly before testing as structural and morphological parameters of the ear can change significantly depending on growing conditions. It was suggested that such parameters as the width and thickness of the ear affect the process of the latter interaction with stripping fingers. Results. Forces of stripping the said wheat varieties were obtained using stripping fingers with a gap of 5–7 mm. Stripping forces of the “Kasar” wheat varied from 17,4 to 24,2 N, under conditions of the gap of 6 mm, and from 13,4 to 16,8, with the gap of 7 mm. Discussion and Conclusion. Dependence of the stripping force on the gap width of stripping fingers was confirmed by results of our experiments. Forces varied in the range of 16,5–20,6 N when stripping off “Moskovskaya 40” wheat in the case of the gap of 5 mm and 8,1–14 N in the case of the 7-mm gap. The effect of such ear parameters as the width, thickness and density was established.