ВОВиктор Николаевич Ожерельев

Виктор Николаевич Ожерельев

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Виктор Николаевич Ожерельев has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Verification of a mathematical model for the territorial distribution of potato farming (case study of Russian regions)

    by V. N. Ozherelyev, A. O. Nikitina, В. Н. Ожерельев, А. О. Никитина

    The article presents the results of an empirical verification of a previously developed mathematical model that allows predicting the efficiency of potato production in different regions, taking into account agroclimatic and macroeconomic factors. Based on data from 23 regions of Central Russia for 2000–2023, a strong correlation was established between the relative cost calculated by the model and the actual dynamics of potato gross harvests. It has been confirmed that the optimum zone for commercial potato farming has shifted to the Bryansk, Tula, and Nizhny Novgorod regions, which is consistent with the model's theoretical conclusions regarding changes in climatic conditions. The obtained results testify to the high prognostic value of the model and the possibility of its use for strategic planning in the agro-industrial complex. The paper provides a detailed analysis of global potato production trends for the period 2000–2024. It shows that Russia, following the global trend in developed countries, reduced its gross harvest by 37.4%, while simultaneously decreasing the sown area from 2.834 million hectares to 1.075 million hectares. Profound regional differentiation is revealed: against the backdrop of a general decline, three regions (Bryansk, Tula, and Nizhny Novgorod Oblasts) demonstrated production growth of 179.3%, 125.7%, and 114.3%, respectively. It is established that it is in these regions that the share of private household plots in the gross harvest is minimal (from 12.4% to 36.2%), indicating the industrialization of potato farming. The determination coefficient (R² = 0.7312) confirms that the model explains more than 73% of the variance in regional changes. The extreme drought of 2010 served as a natural experiment: in the Bryansk region, crop yields declined by only 17.5% (compared to an average decline of 38% for the Central Federal District), confirming the adequacy of the moisture availability and drought risk factors factored into the model. The verification results allow the model to be recommended for substantiating investment decisions, assessing the effectiveness of government support, and developing strategies for the spatial distribution of potato farming in a changing climate.

  • Open Access

    Experimental Study of the Process of Preliminary Separation of Light Impurities from Combed Heap

    by Vladimir Yu. Savin, Viktor N. Ozherelev, Viktor V. Nikitin, Ivan P. Adylin

    Introduction. There are specified and considered the trends determining the directionsfor the development of grain harvesting equipment. One of the most important issues is increasing the productivity of a grain harvester while maintaining its acceptable metalcontent and energy consumption. Traditional solutions have largely exhausted themselves, so a promising solution is the use of the technology for combing of standing plants.Aim of the Study. The study is aimed at determining the proportion of light impuritiesseparated from the grain heap depending on the height of the combing header outlet.Materials and Methods. There was used an experimental method to examine a combingheader with preliminary separation of light impurities. During the experiment, the height of the stripper header outlet was varied. The mass of the separated chaff and its composition were determined. When processing the experimental data, there were obtained relationships meeting the study objectives. The results are divided into two groups: the results with the use of solid shields installed on the combing header rear wall and those without solid shields, when the rear wall is a mesh surface.Results. There has been developed a method for determining the proportion of separated light impurities. There have been found the dependences of the proportion of separated light impurities and the proportion of lost grain on the combing header outlet height. There has been identified an optimal range of the combing header outlet height if the solid shields removed from the combing header rear wall. If the range of combing header outlet height is from 124 to 130 mm, the proportion of separated light impurities reaches 13%, while grain losses remain relatively low.Discussion and Conclusion. In the context of separating the heap light impurities, there has been obtained a significant result, which allows not only unloading significantly the grain harvester cleaning system and increasing its productivity, but also improving the efficiency of separating grain on the pre-drum separating device or directly on the grate bottom of the inclined chamber.

  • DESIGN FEATURES OF THE VERTICAL CUTTER FOR PLANTATION OF CURRANTS

    by Bryansk State Agrarian University, Viktor Ozherelev

    The problem of maintaining a level transverse profile of the currant bush row spacing is discussed in this article. It has been established that the most suitable method is to use a specialized machine with vertical milling tools. To reduce the negative impact on the bush crowns, it is proposed to move the drive bevel gearbox to an area located above the plants, with the gearbox connected to the milling rotor via a cardan shaft. The rotor is equipped with four L-shaped, outward-curving blades. Its axis of rotation is tilted forward and toward the row spacing, resulting in the throwing of soil cut by the blade back and toward the row spacing, which leads to a leveling of the transverse profile of the surface. It is noted that when the milling support wheel follows deep furrows, the telescopic portion of the cardan shaft temporarily jams. Measurements of the cutting force during interaction between the L-shaped blade and the soil at different depths of its stroke were performed to correctly explain this phenomenon. The maximum force was determined to be 941.76 N with a working width of 35 mm. Based on these results, the normal pressure between the square shaft rib and the contact surfaces of the telescopic tube was calculated. The friction force in the cardan shaft sliding coupler was calculated to be 2972 N. Since this friction force significantly exceeds the cutter's weight, this is the cause of the telescopic joint jamming. This negative phenomenon can be virtually eliminated by lubricating the telescopic coupler or mounting the gearbox on a articulated linkage system, allowing it to replicate the vertical oscillations of the cutter as its wheel follows the row spacing.

  • RESULTS OF STUDYING THE ELASTIC PROPERTIES OF BARLEY AND WHEAT CEREAL

    by Bryansk State Agrarian University, Viktor Ozherelev, Viktor Nikitin, Ivan Adylin

    The possibility of using the accelerator drum of the threshing device of a combine harvester for separating the stripped heap in order to extract free grain from it is considered in the article. It is indicated that a significant change in the composition and main characteristics of the incoming heap can lead to a radical change in the principle of interaction with it of the beaters of the accelerator drum. It is noted that in order to optimize the process, a more in-depth study of the physical and mechanical properties of the heap, in particular, the elastic properties of the grain grains, is advisable. 170 grain grains of barley of the Nadezhny variety and 150 grains of wheat of the Moskovskaya 56 variety. Each grain was dropped from a height of 123 mm onto a steel plate 25 mm thick were subjected to study. The process was recorded using video filming and the exact rebound height was established. The resulting distribution of grain grains by rebound height ranges was tested for compliance with the normal law using the Pearson criterion. A negative result was obtained, since the distributions have a pronounced asymmetric character with a shift towards a lower rebound height. It was found that most of the kinetic energy of the grain accumulated as a result of the fall does not transform into rebound energy, but dissipates into interacting bodies. As a result, the internal structure of the grain is transformed at the micro level, up to its partial or complete destruction. The high degree of differentiation of the rebound height from 2 to 59 mm in the experiment can be explained by the preliminary interaction of the grains with the beaters of the threshing drum during harvesting. It is advisable to provide the surfaces of the beaters in contact with the grain with an elastic coating when reorienting the accelerator drum to separate the combed heap.

  • Open Access

    The effect of the recirculation coefficient of the drying agent on its temperature in the aerodynamic heating dryer

    by Viktor N. Ozherelyev, Aleksey I. Kupreenko, Dmitry A. Bezik, Khafiz M. Isaev, Oleg A. Kupreenko, Исаев Хафиз Мубариз-Оглы

    BACKGROUND: The expansion of the functionality of chamber dryers of aerodynamic heating is possible by equipping them with additional modules, for example, in the form of a drying shaft for grain. However, it is necessary to ensure the implementation of the basic principle of operation of aerodynamic heating dryers – recirculation of the drying agent with its partial discharge during the drying process. AIM: Determination of the dependence of the temperature of the drying agent on the recirculation coefficient of the spent drying agent when using an additional module in the form of a drying shaft for grain. MATERIALS AND METHODS: A differential equation was obtained from the heat balance equation of the dryer in an infinitesimal period of time, as a result of solving which the desired dependence was found by the second-order Euler method. Graphs of the temperature change of the drying agent during the grain drying process are constructed for the accepted initial data with a value of the recirculation coefficient equal to 0.3, 0.5, 0.7 and the moisture content of the spent drying agent equal to 0.012 and 0.041 kg/kg d.a. RESULTS: The analysis of the dependencies showed that the temperature of the drying agent increases with an increase in the recirculation coefficient and moisture content of the drying agent. The maximum possible temperature of the drying agent for a recirculation coefficient equal to 0.3 will be 135 °C, for a recirculation coefficient equal to 0.5–158 ° C, for a recirculation coefficient equal to 0.7–198 ° C. Maintaining the set temperature of the drying agent is ensured by adjusting the recirculation coefficient of the spent drying agent by changing its flow rate in the recirculation channel. CONCLUSION: The dependence obtained on the basis of the heat balance of the dryer makes it possible to predict the temperature of the drying agent depending on the established recirculation coefficient of the spent drying agent at a given range of changes in its moisture content. At the same time, the operating mode of the aerodynamic heating dryer is ensured even when using its additional modules.

  • Open Access

    The influence of the composition of the combed grain heap on the preliminary separation of loose grain

    by Viktor N. Ozhereliev, Viktor V. Nikitin, Vladimir Юрьевич Yurievich Savin, Natalia V. Sinyaya, Синяя Наталия Викторовна

    BACKGROUND: The paper reviews the state of the problem of grain harvesting by the method of combing plants on the root. Attention is focused on the potential economic efficiency of the method and on the scientific and technological problems hindering its widespread implementation. In particular, in order to reduce the degree of crushing of loose grain, it is necessary to separate it preliminary and prevent it from entering the threshing device. It is proposed to remove grain directly on the lattice bottom of the inclined chamber of the combine harvester. The scientific hypothesis of the study suggests that in order to improve separation, it is advisable to remove a significant part of light impurities from the pile directly preliminary in the body of the combing adapter. AIM: Evaluation of the efficiency of separation of loose grain by removing a significant part of light impurities from the combed pile before it enters the inclined chamber. METHODS: To confirm the hypothesis, the experiment was conducted in which a combed grain pile of wheat of the «Moskovskaya 56» variety of different component composition was fed to a lattice surface equipped with a scraper conveyor. The weight content of the grain varied from 70 to 100%. The experiment took into account the proportion of loose grain that passed through the holes of the grate at its length of 920 mm and the width of the holes of 12 mm. It ranged from 65 to 80% as the content of loose grain in the pile increased. RESULTS: According to the study results, it was found that the passage of loose grain through the openings of the lattice bottom varies between 65-80%. At the same time, a decrease in the mass fraction of loose grain in the pile reduces its passage through the openings of the lattice surface by 15%. CONCLUSION: Preliminary removal of light impurities from the combed grain pile, comparable in size to loose grain, can be carried out by using an inertial separation system. Reducing the proportion of light impurities in the pile entering the combine harvester cleaning system makes it possible to significantly increase the efficiency of its operation.


  • Open Access

    Separating Light Impurities from the Combed Heap in the Adapter Case

    by Vladimir Yu. Savin, Viktor N. Ozherelev, Viktor V. Nikitin

    Introduction. It is possible to increase the separating of loose grain on the lattice bottom of the combine harvester feeder house by removing most of the light impurities from the combed heap using an inertial cleaning system built into the combing adapter body.Aim of the Study. The study is aimed at developing an inertial system for separating light impurities in the combing header body and optimizing its main parameters.Materials and Methods. The object of the study was a large-scale model of a pneumatic cleaning device to simulate the motion of air and components of a combed grain heap inside the combing adapter body. It was a two-factor experiment with three variations of the air flow velocity (4.5; 5.5; 6.5 m/s) and the width of the air channel (0.26; 0.29; 0.32 m). The studies were conducted on a combed heap of Moskovskaya 56 wheat with a moisture content of about 12%. As a parameter for optimization and response function, a portion of the combed heap was selected from the body of the installation with an air flow.Results. According to the results of the experimental studies, it was found that the air flow velocity has a greater effect on separating glumes than the width of the air channel. A simultaneous increase in both factors leads to an improved separation. At the same time, if increasing the air flow velocity ensures a stable increase in the proportion of the combed heap and is limited only by the air velocity at which grain appears in the combed heap along with the glumes, then changing the channel width allows achieving the parameter optimal value.Discussion and Conclusions. The use of an inertial cleaning system makes it possible to remove almost completely light impurities from the combed heap. The optimal parameters of the device are: channel width 0.28...0.3 m, air flow velocity 6...6.5 m/s.


  • INFLUENCE OF THE COMPOSITION OF COLLECTED GRAIN HEAP ON THE EFFICIENCY OF ITS SEPARATION ON A GRID SURFACE

    by Bryansk State Agrarian University, Viktor Ozherelev, Viktor Nikitin, Vladimir Savin, Kaluga branch of Moscow State Technical University named after N.E. Bauman

    The separating ability of the lattice surface when working with combed grain heaps of various fractional compositions was studied. The scientific hypothesis of the study is the assumption that with an increase in the mass fraction of chaff in the heap, the separation efficiency should decrease due to an increase in the volume of grain with a constant mass of the sample of the heap under study as the grain content decreases due to the larger volumetric mass of the latter compared to the chaff. It is a legitimate assumption that the passage of a larger volume of heap through the holes of the lattice surface requires more time, that is, the separation rate should decrease. Experimental studies were carried out on a combed grain heap of wheat variety Moskovskaya 56 with a relative humidity of 12%. The mass fraction of grain in the heap varied from 100 to 60% in increments of 10%. The experimental installation was made on the basis of the grain elevator of the KZS 1218 combine harvester, in which, instead of the dismantled lower wall, a lattice surface with longitudinal holes 900 mm long and 12 mm wide was installed. The installation simulated the operation of the inclined chamber of a combine harvester, the lattice bottom of which should separate free grain from the combed heap and direct it for cleaning, bypassing the threshing apparatus. In this regard, the speed of the scraper conveyor was 3 m/s. The heap that passed through the holes in the lattice was caught, after which it was disassembled into fractions and accounted for. As a result of the experiment, it was established that as the mass fraction of grain in the heap decreases, the separation rate of the latter within the zone of variation of the initial parameter decreases by 4%. Therefore, it is advisable to first remove a significant portion of light impurities from the combed heap before it enters the inclined chamber.

  • Open Access

    Influence of the Grid Inclination Angle on the Efficiency of Preliminary Separation of the Combed Heap

    by Viktor V. Nikitin, Viktor N. Ozherelev

    A highly topical scientific and practical task is to justify the choice of the most advanced variant of the device for pre-separating the combed heap and to optimize its design.


  • Open Access

    Mathematical model of the cross-section of wheat grain

    by Victor V. Nikitin, Victor N. Ozhereliev, Natalia V. Sinyaya, Ожерельев Виктор Николаевич, Синяя Наталия Викторовна

    BACKGROUND: When studying the optimal length of the holes in the lattice bottom of the inclined chamber of a combine harvester, which ensures preliminary separation of the combed grain heap, the cross section of wheat grain was modeled in the shape of a separate ball or a cut cylinder. This is due to the fact that the description of the technological process is significantly simplified with this shape of grain. However, such models of the grain cross-section are very far from the real shape of the object, since the dorsal side of the grains is convex, and there is a longitudinal groove on the ventral side. The kind of surface closest to the real shape of the grain is the Pascal’s snail mathematical model. For this model, the centroid coordinates are determined, and equations are obtained for calculating its cross-sectional area and moments of inertia for each coordinate axis. Verification of the obtained equations in the KOMPAS-3D software showed that the discrepancy between the real and theoretically predicted values of the centroid coordinates is about 13%, which reduces the adequacy of the calculations and requires their refinement. AIM: Refinement of the mathematical model of the cross-section of wheat grain shaped as the Pascal’s snail. METHODS: The object of the study is a cross section of wheat grain shaped as the Pascal’s snail. When determining the centroid coordinates, methods of theoretical mechanics were used, and the resulting expressions were verified in the KOMPAS-3D three-dimensional modeling software. RESULTS: Mathematical expressions for analytical calculation of the centroid coordinates are obtained for different versions of the Pascal’s snail: a = b (cardioid), a b (the Pascal’s snail without an internal loop), a b (the Pascal’s snail with an internal loop). Verification of the obtained expressions proves their adequacy, since the convergence of theoretical and experimental data is 100%. CONCLUSIONS: The use of refined mathematical models of the cross-section of wheat grain can significantly simplify the modeling of the separation process of combed heaps, as well as to increase the accuracy of calculations. To simplify the description of this process, it is advisable to use the KOMPAS-3D three-dimensional modeling software.