Viktor V. Nikitin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Viktor V. Nikitin has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Виктор Николаевич Ожерельев
Брянский государственный аграрный университет
12 shared publications - Natalia V. Sinyaya
Bryansk State Agrarian University
5 shared publications - Vladimir Yu. Savin
Bauman Moscow State Technical University
4 shared publications - Синяя Наталия Викторовна
Брянский государственный аграрный университет
4 shared publications Bryansk State Agrarian University
3 shared publicationsVictor N. Ozhereliev
Bryansk State Agrarian University
3 shared publications
Latest Publications
- Open Access
- 22 December 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (4) , 641-657
Experimental Study of the Process of Preliminary Separation of Light Impurities from Combed Heap
Introduction. There are specified and considered the trends determining the directionsfor the development of grain harvesting equipment. One of the most important issues is increasing the productivity of a grain harvester while maintaining its acceptable metalcontent and energy consumption. Traditional solutions have largely exhausted themselves, so a promising solution is the use of the technology for combing of standing plants.Aim of the Study. The study is aimed at determining the proportion of light impuritiesseparated from the grain heap depending on the height of the combing header outlet.Materials and Methods. There was used an experimental method to examine a combingheader with preliminary separation of light impurities. During the experiment, the height of the stripper header outlet was varied. The mass of the separated chaff and its composition were determined. When processing the experimental data, there were obtained relationships meeting the study objectives. The results are divided into two groups: the results with the use of solid shields installed on the combing header rear wall and those without solid shields, when the rear wall is a mesh surface.Results. There has been developed a method for determining the proportion of separated light impurities. There have been found the dependences of the proportion of separated light impurities and the proportion of lost grain on the combing header outlet height. There has been identified an optimal range of the combing header outlet height if the solid shields removed from the combing header rear wall. If the range of combing header outlet height is from 124 to 130 mm, the proportion of separated light impurities reaches 13%, while grain losses remain relatively low.Discussion and Conclusion. In the context of separating the heap light impurities, there has been obtained a significant result, which allows not only unloading significantly the grain harvester cleaning system and increasing its productivity, but also improving the efficiency of separating grain on the pre-drum separating device or directly on the grate bottom of the inclined chamber.
- 22 December 2025
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 35 (4) , 641-657
Open AccessExperimental Study of the Process of Preliminary Separation of Light Impurities from Combed Heap
Introduction. There are specified and considered the trends determining the directionsfor the development of grain harvesting equipment. One of the most important issues is increasing the productivity of a grain harvester while maintaining its acceptable metalcontent and energy consumption. Traditional solutions have largely exhausted themselves, so a promising solution is the use of the technology for combing of standing plants.Aim of the Study. The study is aimed at determining the proportion of light impuritiesseparated from the grain heap depending on the height of the combing header outlet.Materials and Methods. There was used an experimental method to examine a combingheader with preliminary separation of light impurities. During the experiment, the height of the stripper header outlet was varied. The mass of the separated chaff and its composition were determined. When processing the experimental data, there were obtained relationships meeting the study objectives. The results are divided into two groups: the results with the use of solid shields installed on the combing header rear wall and those without solid shields, when the rear wall is a mesh surface.Results. There has been developed a method for determining the proportion of separated light impurities. There have been found the dependences of the proportion of separated light impurities and the proportion of lost grain on the combing header outlet height. There has been identified an optimal range of the combing header outlet height if the solid shields removed from the combing header rear wall. If the range of combing header outlet height is from 124 to 130 mm, the proportion of separated light impurities reaches 13%, while grain losses remain relatively low.Discussion and Conclusion. In the context of separating the heap light impurities, there has been obtained a significant result, which allows not only unloading significantly the grain harvester cleaning system and increasing its productivity, but also improving the efficiency of separating grain on the pre-drum separating device or directly on the grate bottom of the inclined chamber.
- 29 August 2025
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 4
RESULTS OF STUDYING THE ELASTIC PROPERTIES OF BARLEY AND WHEAT CEREAL
The possibility of using the accelerator drum of the threshing device of a combine harvester for separating the stripped heap in order to extract free grain from it is considered in the article. It is indicated that a significant change in the composition and main characteristics of the incoming heap can lead to a radical change in the principle of interaction with it of the beaters of the accelerator drum. It is noted that in order to optimize the process, a more in-depth study of the physical and mechanical properties of the heap, in particular, the elastic properties of the grain grains, is advisable. 170 grain grains of barley of the Nadezhny variety and 150 grains of wheat of the Moskovskaya 56 variety. Each grain was dropped from a height of 123 mm onto a steel plate 25 mm thick were subjected to study. The process was recorded using video filming and the exact rebound height was established. The resulting distribution of grain grains by rebound height ranges was tested for compliance with the normal law using the Pearson criterion. A negative result was obtained, since the distributions have a pronounced asymmetric character with a shift towards a lower rebound height. It was found that most of the kinetic energy of the grain accumulated as a result of the fall does not transform into rebound energy, but dissipates into interacting bodies. As a result, the internal structure of the grain is transformed at the micro level, up to its partial or complete destruction. The high degree of differentiation of the rebound height from 2 to 59 mm in the experiment can be explained by the preliminary interaction of the grains with the beaters of the threshing drum during harvesting. It is advisable to provide the surfaces of the beaters in contact with the grain with an elastic coating when reorienting the accelerator drum to separate the combed heap.
- 29 August 2025
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 4
RESULTS OF STUDYING THE ELASTIC PROPERTIES OF BARLEY AND WHEAT CEREAL
The possibility of using the accelerator drum of the threshing device of a combine harvester for separating the stripped heap in order to extract free grain from it is considered in the article. It is indicated that a significant change in the composition and main characteristics of the incoming heap can lead to a radical change in the principle of interaction with it of the beaters of the accelerator drum. It is noted that in order to optimize the process, a more in-depth study of the physical and mechanical properties of the heap, in particular, the elastic properties of the grain grains, is advisable. 170 grain grains of barley of the Nadezhny variety and 150 grains of wheat of the Moskovskaya 56 variety. Each grain was dropped from a height of 123 mm onto a steel plate 25 mm thick were subjected to study. The process was recorded using video filming and the exact rebound height was established. The resulting distribution of grain grains by rebound height ranges was tested for compliance with the normal law using the Pearson criterion. A negative result was obtained, since the distributions have a pronounced asymmetric character with a shift towards a lower rebound height. It was found that most of the kinetic energy of the grain accumulated as a result of the fall does not transform into rebound energy, but dissipates into interacting bodies. As a result, the internal structure of the grain is transformed at the micro level, up to its partial or complete destruction. The high degree of differentiation of the rebound height from 2 to 59 mm in the experiment can be explained by the preliminary interaction of the grains with the beaters of the threshing drum during harvesting. It is advisable to provide the surfaces of the beaters in contact with the grain with an elastic coating when reorienting the accelerator drum to separate the combed heap.
- Open Access
- 6 December 2024
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 91 (5) , 553-561
The influence of the composition of the combed grain heap on the preliminary separation of loose grain
BACKGROUND: The paper reviews the state of the problem of grain harvesting by the method of combing plants on the root. Attention is focused on the potential economic efficiency of the method and on the scientific and technological problems hindering its widespread implementation. In particular, in order to reduce the degree of crushing of loose grain, it is necessary to separate it preliminary and prevent it from entering the threshing device. It is proposed to remove grain directly on the lattice bottom of the inclined chamber of the combine harvester. The scientific hypothesis of the study suggests that in order to improve separation, it is advisable to remove a significant part of light impurities from the pile directly preliminary in the body of the combing adapter. AIM: Evaluation of the efficiency of separation of loose grain by removing a significant part of light impurities from the combed pile before it enters the inclined chamber. METHODS: To confirm the hypothesis, the experiment was conducted in which a combed grain pile of wheat of the «Moskovskaya 56» variety of different component composition was fed to a lattice surface equipped with a scraper conveyor. The weight content of the grain varied from 70 to 100%. The experiment took into account the proportion of loose grain that passed through the holes of the grate at its length of 920 mm and the width of the holes of 12 mm. It ranged from 65 to 80% as the content of loose grain in the pile increased. RESULTS: According to the study results, it was found that the passage of loose grain through the openings of the lattice bottom varies between 65-80%. At the same time, a decrease in the mass fraction of loose grain in the pile reduces its passage through the openings of the lattice surface by 15%. CONCLUSION: Preliminary removal of light impurities from the combed grain pile, comparable in size to loose grain, can be carried out by using an inertial separation system. Reducing the proportion of light impurities in the pile entering the combine harvester cleaning system makes it possible to significantly increase the efficiency of its operation.
- 6 December 2024
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 91 (5) , 553-561
Open AccessThe influence of the composition of the combed grain heap on the preliminary separation of loose grain
BACKGROUND: The paper reviews the state of the problem of grain harvesting by the method of combing plants on the root. Attention is focused on the potential economic efficiency of the method and on the scientific and technological problems hindering its widespread implementation. In particular, in order to reduce the degree of crushing of loose grain, it is necessary to separate it preliminary and prevent it from entering the threshing device. It is proposed to remove grain directly on the lattice bottom of the inclined chamber of the combine harvester. The scientific hypothesis of the study suggests that in order to improve separation, it is advisable to remove a significant part of light impurities from the pile directly preliminary in the body of the combing adapter. AIM: Evaluation of the efficiency of separation of loose grain by removing a significant part of light impurities from the combed pile before it enters the inclined chamber. METHODS: To confirm the hypothesis, the experiment was conducted in which a combed grain pile of wheat of the «Moskovskaya 56» variety of different component composition was fed to a lattice surface equipped with a scraper conveyor. The weight content of the grain varied from 70 to 100%. The experiment took into account the proportion of loose grain that passed through the holes of the grate at its length of 920 mm and the width of the holes of 12 mm. It ranged from 65 to 80% as the content of loose grain in the pile increased. RESULTS: According to the study results, it was found that the passage of loose grain through the openings of the lattice bottom varies between 65-80%. At the same time, a decrease in the mass fraction of loose grain in the pile reduces its passage through the openings of the lattice surface by 15%. CONCLUSION: Preliminary removal of light impurities from the combed grain pile, comparable in size to loose grain, can be carried out by using an inertial separation system. Reducing the proportion of light impurities in the pile entering the combine harvester cleaning system makes it possible to significantly increase the efficiency of its operation.
- Open Access
- 24 September 2024
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 34 (3) , 370-387
Separating Light Impurities from the Combed Heap in the Adapter Case
Introduction. It is possible to increase the separating of loose grain on the lattice bottom of the combine harvester feeder house by removing most of the light impurities from the combed heap using an inertial cleaning system built into the combing adapter body.Aim of the Study. The study is aimed at developing an inertial system for separating light impurities in the combing header body and optimizing its main parameters.Materials and Methods. The object of the study was a large-scale model of a pneumatic cleaning device to simulate the motion of air and components of a combed grain heap inside the combing adapter body. It was a two-factor experiment with three variations of the air flow velocity (4.5; 5.5; 6.5 m/s) and the width of the air channel (0.26; 0.29; 0.32 m). The studies were conducted on a combed heap of Moskovskaya 56 wheat with a moisture content of about 12%. As a parameter for optimization and response function, a portion of the combed heap was selected from the body of the installation with an air flow.Results. According to the results of the experimental studies, it was found that the air flow velocity has a greater effect on separating glumes than the width of the air channel. A simultaneous increase in both factors leads to an improved separation. At the same time, if increasing the air flow velocity ensures a stable increase in the proportion of the combed heap and is limited only by the air velocity at which grain appears in the combed heap along with the glumes, then changing the channel width allows achieving the parameter optimal value.Discussion and Conclusions. The use of an inertial cleaning system makes it possible to remove almost completely light impurities from the combed heap. The optimal parameters of the device are: channel width 0.28...0.3 m, air flow velocity 6...6.5 m/s.
- 24 September 2024
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 34 (3) , 370-387
Open AccessSeparating Light Impurities from the Combed Heap in the Adapter Case
Introduction. It is possible to increase the separating of loose grain on the lattice bottom of the combine harvester feeder house by removing most of the light impurities from the combed heap using an inertial cleaning system built into the combing adapter body.Aim of the Study. The study is aimed at developing an inertial system for separating light impurities in the combing header body and optimizing its main parameters.Materials and Methods. The object of the study was a large-scale model of a pneumatic cleaning device to simulate the motion of air and components of a combed grain heap inside the combing adapter body. It was a two-factor experiment with three variations of the air flow velocity (4.5; 5.5; 6.5 m/s) and the width of the air channel (0.26; 0.29; 0.32 m). The studies were conducted on a combed heap of Moskovskaya 56 wheat with a moisture content of about 12%. As a parameter for optimization and response function, a portion of the combed heap was selected from the body of the installation with an air flow.Results. According to the results of the experimental studies, it was found that the air flow velocity has a greater effect on separating glumes than the width of the air channel. A simultaneous increase in both factors leads to an improved separation. At the same time, if increasing the air flow velocity ensures a stable increase in the proportion of the combed heap and is limited only by the air velocity at which grain appears in the combed heap along with the glumes, then changing the channel width allows achieving the parameter optimal value.Discussion and Conclusions. The use of an inertial cleaning system makes it possible to remove almost completely light impurities from the combed heap. The optimal parameters of the device are: channel width 0.28...0.3 m, air flow velocity 6...6.5 m/s.
- 27 April 2024
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 2
INFLUENCE OF THE COMPOSITION OF COLLECTED GRAIN HEAP ON THE EFFICIENCY OF ITS SEPARATION ON A GRID SURFACE
The separating ability of the lattice surface when working with combed grain heaps of various fractional compositions was studied. The scientific hypothesis of the study is the assumption that with an increase in the mass fraction of chaff in the heap, the separation efficiency should decrease due to an increase in the volume of grain with a constant mass of the sample of the heap under study as the grain content decreases due to the larger volumetric mass of the latter compared to the chaff. It is a legitimate assumption that the passage of a larger volume of heap through the holes of the lattice surface requires more time, that is, the separation rate should decrease. Experimental studies were carried out on a combed grain heap of wheat variety Moskovskaya 56 with a relative humidity of 12%. The mass fraction of grain in the heap varied from 100 to 60% in increments of 10%. The experimental installation was made on the basis of the grain elevator of the KZS 1218 combine harvester, in which, instead of the dismantled lower wall, a lattice surface with longitudinal holes 900 mm long and 12 mm wide was installed. The installation simulated the operation of the inclined chamber of a combine harvester, the lattice bottom of which should separate free grain from the combed heap and direct it for cleaning, bypassing the threshing apparatus. In this regard, the speed of the scraper conveyor was 3 m/s. The heap that passed through the holes in the lattice was caught, after which it was disassembled into fractions and accounted for. As a result of the experiment, it was established that as the mass fraction of grain in the heap decreases, the separation rate of the latter within the zone of variation of the initial parameter decreases by 4%. Therefore, it is advisable to first remove a significant portion of light impurities from the combed heap before it enters the inclined chamber.
- 27 April 2024
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 2
INFLUENCE OF THE COMPOSITION OF COLLECTED GRAIN HEAP ON THE EFFICIENCY OF ITS SEPARATION ON A GRID SURFACE
The separating ability of the lattice surface when working with combed grain heaps of various fractional compositions was studied. The scientific hypothesis of the study is the assumption that with an increase in the mass fraction of chaff in the heap, the separation efficiency should decrease due to an increase in the volume of grain with a constant mass of the sample of the heap under study as the grain content decreases due to the larger volumetric mass of the latter compared to the chaff. It is a legitimate assumption that the passage of a larger volume of heap through the holes of the lattice surface requires more time, that is, the separation rate should decrease. Experimental studies were carried out on a combed grain heap of wheat variety Moskovskaya 56 with a relative humidity of 12%. The mass fraction of grain in the heap varied from 100 to 60% in increments of 10%. The experimental installation was made on the basis of the grain elevator of the KZS 1218 combine harvester, in which, instead of the dismantled lower wall, a lattice surface with longitudinal holes 900 mm long and 12 mm wide was installed. The installation simulated the operation of the inclined chamber of a combine harvester, the lattice bottom of which should separate free grain from the combed heap and direct it for cleaning, bypassing the threshing apparatus. In this regard, the speed of the scraper conveyor was 3 m/s. The heap that passed through the holes in the lattice was caught, after which it was disassembled into fractions and accounted for. As a result of the experiment, it was established that as the mass fraction of grain in the heap decreases, the separation rate of the latter within the zone of variation of the initial parameter decreases by 4%. Therefore, it is advisable to first remove a significant portion of light impurities from the combed heap before it enters the inclined chamber.
- Open Access
- 29 March 2024
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 34 (1) , 26-43
Influence of the Grid Inclination Angle on the Efficiency of Preliminary Separation of the Combed Heap
A highly topical scientific and practical task is to justify the choice of the most advanced variant of the device for pre-separating the combed heap and to optimize its design.
- 29 March 2024
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 34 (1) , 26-43
Open AccessInfluence of the Grid Inclination Angle on the Efficiency of Preliminary Separation of the Combed Heap
A highly topical scientific and practical task is to justify the choice of the most advanced variant of the device for pre-separating the combed heap and to optimize its design.
- Open Access
- 15 March 2024
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 91 (1) , 91-100
Mathematical model of the cross-section of wheat grain
BACKGROUND: When studying the optimal length of the holes in the lattice bottom of the inclined chamber of a combine harvester, which ensures preliminary separation of the combed grain heap, the cross section of wheat grain was modeled in the shape of a separate ball or a cut cylinder. This is due to the fact that the description of the technological process is significantly simplified with this shape of grain. However, such models of the grain cross-section are very far from the real shape of the object, since the dorsal side of the grains is convex, and there is a longitudinal groove on the ventral side. The kind of surface closest to the real shape of the grain is the Pascal’s snail mathematical model. For this model, the centroid coordinates are determined, and equations are obtained for calculating its cross-sectional area and moments of inertia for each coordinate axis. Verification of the obtained equations in the KOMPAS-3D software showed that the discrepancy between the real and theoretically predicted values of the centroid coordinates is about 13%, which reduces the adequacy of the calculations and requires their refinement. AIM: Refinement of the mathematical model of the cross-section of wheat grain shaped as the Pascal’s snail. METHODS: The object of the study is a cross section of wheat grain shaped as the Pascal’s snail. When determining the centroid coordinates, methods of theoretical mechanics were used, and the resulting expressions were verified in the KOMPAS-3D three-dimensional modeling software. RESULTS: Mathematical expressions for analytical calculation of the centroid coordinates are obtained for different versions of the Pascal’s snail: a = b (cardioid), a b (the Pascal’s snail without an internal loop), a b (the Pascal’s snail with an internal loop). Verification of the obtained expressions proves their adequacy, since the convergence of theoretical and experimental data is 100%. CONCLUSIONS: The use of refined mathematical models of the cross-section of wheat grain can significantly simplify the modeling of the separation process of combed heaps, as well as to increase the accuracy of calculations. To simplify the description of this process, it is advisable to use the KOMPAS-3D three-dimensional modeling software.
- 15 March 2024
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 91 (1) , 91-100
Open AccessMathematical model of the cross-section of wheat grain
BACKGROUND: When studying the optimal length of the holes in the lattice bottom of the inclined chamber of a combine harvester, which ensures preliminary separation of the combed grain heap, the cross section of wheat grain was modeled in the shape of a separate ball or a cut cylinder. This is due to the fact that the description of the technological process is significantly simplified with this shape of grain. However, such models of the grain cross-section are very far from the real shape of the object, since the dorsal side of the grains is convex, and there is a longitudinal groove on the ventral side. The kind of surface closest to the real shape of the grain is the Pascal’s snail mathematical model. For this model, the centroid coordinates are determined, and equations are obtained for calculating its cross-sectional area and moments of inertia for each coordinate axis. Verification of the obtained equations in the KOMPAS-3D software showed that the discrepancy between the real and theoretically predicted values of the centroid coordinates is about 13%, which reduces the adequacy of the calculations and requires their refinement. AIM: Refinement of the mathematical model of the cross-section of wheat grain shaped as the Pascal’s snail. METHODS: The object of the study is a cross section of wheat grain shaped as the Pascal’s snail. When determining the centroid coordinates, methods of theoretical mechanics were used, and the resulting expressions were verified in the KOMPAS-3D three-dimensional modeling software. RESULTS: Mathematical expressions for analytical calculation of the centroid coordinates are obtained for different versions of the Pascal’s snail: a = b (cardioid), a b (the Pascal’s snail without an internal loop), a b (the Pascal’s snail with an internal loop). Verification of the obtained expressions proves their adequacy, since the convergence of theoretical and experimental data is 100%. CONCLUSIONS: The use of refined mathematical models of the cross-section of wheat grain can significantly simplify the modeling of the separation process of combed heaps, as well as to increase the accuracy of calculations. To simplify the description of this process, it is advisable to use the KOMPAS-3D three-dimensional modeling software.
- Open Access
- 14 September 2023
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 90 (3) , 217-224
Reducing the range of soil discarding by disc harrows in berry fields
BACKGROUND: The subject of research is the process of transverse discarding of soil by the outer disk mounted on the front section of a disk harrow in the conditions of inter-row spacing of a berry plantation. AIMS: Reduction of the range of discarding of a soil layer by the outer disk mounted on the front section of a disk harrow in the conditions of inter-row spacing of a berry plantation. METHODS: All studies were carried out on a raspberry plantation. Soil moisture was 28%. The disc harrow was aggregated with the T-25A tractor moved at a constant speed of 7.29 km/h, had an attack angle of 21 and a processing depth of 0.1 m. While carrying out field experiments, the location of all soil fragments outside the furrow formed by the outer disk of the rear section was considered. Both the distance to the fragment edge furthest from the furrow wall and the fragments slope relative to ч were recorded. RESULTS: According to the results of field experiments, it was found that the value of the transverse discharge of waterlogged and over-compacted soil in inter-row spacing of berry bushes significantly exceeds the amount of overlap between the front and rear sections of the disc harrow. To exclude the soil discarding into the bush area, the disc harrow was equipped with an additional bump shield oriented at an angle of 5354 in horizontal plane and at an angle of 50-58 to the direction of movement of the harrow. CONCLUSIONS: The practical implementation of this technical solution makes it possible to maintain the surface of inter-row spacing at a leveled state throughout their entire service life. At the same time, the disk harrow operates steadily, both with a high degree of impurity of inter-row spacing and excessive soil moisture, as well as provides with grinding and sealing of the annually cut-out raspberry stems.
- 14 September 2023
- Published by ECO-Vector LLC in Tractors and Agricultural Machinery
- Vol. 90 (3) , 217-224
Open AccessReducing the range of soil discarding by disc harrows in berry fields
BACKGROUND: The subject of research is the process of transverse discarding of soil by the outer disk mounted on the front section of a disk harrow in the conditions of inter-row spacing of a berry plantation. AIMS: Reduction of the range of discarding of a soil layer by the outer disk mounted on the front section of a disk harrow in the conditions of inter-row spacing of a berry plantation. METHODS: All studies were carried out on a raspberry plantation. Soil moisture was 28%. The disc harrow was aggregated with the T-25A tractor moved at a constant speed of 7.29 km/h, had an attack angle of 21 and a processing depth of 0.1 m. While carrying out field experiments, the location of all soil fragments outside the furrow formed by the outer disk of the rear section was considered. Both the distance to the fragment edge furthest from the furrow wall and the fragments slope relative to ч were recorded. RESULTS: According to the results of field experiments, it was found that the value of the transverse discharge of waterlogged and over-compacted soil in inter-row spacing of berry bushes significantly exceeds the amount of overlap between the front and rear sections of the disc harrow. To exclude the soil discarding into the bush area, the disc harrow was equipped with an additional bump shield oriented at an angle of 5354 in horizontal plane and at an angle of 50-58 to the direction of movement of the harrow. CONCLUSIONS: The practical implementation of this technical solution makes it possible to maintain the surface of inter-row spacing at a leveled state throughout their entire service life. At the same time, the disk harrow operates steadily, both with a high degree of impurity of inter-row spacing and excessive soil moisture, as well as provides with grinding and sealing of the annually cut-out raspberry stems.
- Open Access
- 30 June 2023
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 33 (2)
Improving the Design of the Disc Harrow for Berry Plantations
Reducing the distance of throwing soil into the zone around bushes and maintaining a leveled surface between rows of berry crops are urgent scientific problems.
- 30 June 2023
- Published by National Research Mordovia State University MRSU in Engineering Technologies and Systems
- Vol. 33 (2)
Open AccessImproving the Design of the Disc Harrow for Berry Plantations
Reducing the distance of throwing soil into the zone around bushes and maintaining a leveled surface between rows of berry crops are urgent scientific problems.
- 28 February 2023
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 1
TO THE SUBSTANTIATION OF THE METHOD OF PRELIMINARY SEPARATION OF FREE GRAIN IN THE ROOT OF PLANTS
The results of theoretical studies confirming the possibility of carrying out preliminary separation of free grain from the stripped grain pile before it enters the threshing chamber of a combine harvester are presented. The prospect of a separating device mounted directly in front of the threshing drum, consisting of longitudinal rods, over which an additional scraper conveyor is mounted, has been established. The cross section of each strip of the grating is narrowed downwards to increase the intensity of separation of the device and eliminate the possibility of clogging the holes with passing particles of the heap. The optimal length of the openings of the pre-drum type separating device, its spatial orientation were determined, and the quality indicators of the work were evaluated. Theoretical studies of the separation process on winter wheat of the “Moskovskaya 56” variety with a grain size of 3.9x6.5 mm were performed. The speed of the scraper conveyor was 3 m/s, and the angle of inclination of the separating device varied within 0-45 degrees. It has been established from the results of research that with an increase in the angle of inclination of the separating surface, the length of the sieve openings increases, and the separation speed decreases. Since the horizontal grate provides a higher separation rate of free grain, compared to an inclined surface, the use of a pre-drum type separating device is most preferable in relation to the grate bottom of the feeder house of a combine harvester in terms of its performance. It has been established that the length of the separating holes should be at least 0.08 m. Such a technical solution allows minimizing not only the crushing of free grain by the working bodies of the threshing machine, but also to reduce the metal consumption of the separating device.
- 28 February 2023
- Published by All-Russian Research Institute for Use of Machinery and Petroleum Products in Agriculture in SCIENCE IN THE CENTRAL RUSSIA
- No. 1
TO THE SUBSTANTIATION OF THE METHOD OF PRELIMINARY SEPARATION OF FREE GRAIN IN THE ROOT OF PLANTS
The results of theoretical studies confirming the possibility of carrying out preliminary separation of free grain from the stripped grain pile before it enters the threshing chamber of a combine harvester are presented. The prospect of a separating device mounted directly in front of the threshing drum, consisting of longitudinal rods, over which an additional scraper conveyor is mounted, has been established. The cross section of each strip of the grating is narrowed downwards to increase the intensity of separation of the device and eliminate the possibility of clogging the holes with passing particles of the heap. The optimal length of the openings of the pre-drum type separating device, its spatial orientation were determined, and the quality indicators of the work were evaluated. Theoretical studies of the separation process on winter wheat of the “Moskovskaya 56” variety with a grain size of 3.9x6.5 mm were performed. The speed of the scraper conveyor was 3 m/s, and the angle of inclination of the separating device varied within 0-45 degrees. It has been established from the results of research that with an increase in the angle of inclination of the separating surface, the length of the sieve openings increases, and the separation speed decreases. Since the horizontal grate provides a higher separation rate of free grain, compared to an inclined surface, the use of a pre-drum type separating device is most preferable in relation to the grate bottom of the feeder house of a combine harvester in terms of its performance. It has been established that the length of the separating holes should be at least 0.08 m. Such a technical solution allows minimizing not only the crushing of free grain by the working bodies of the threshing machine, but also to reduce the metal consumption of the separating device.