Shuang Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shuang Song has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Menglian Zhao
Institute of VLSI Design, Zhejiang University, Hangzhou, China
15 shared publications - Zhichao Tan
College of Information and Electronics Engineering, Zhejiang University, Hangzhou, China
11 shared publications - Nick Van Helleputte
IMEC
10 shared publications - Chris Van Hoof
IMEC, Leuven, Belgium
8 shared publications - Mengyu Li
Zhejiang University
8 shared publications - Kai Huang
Zhejiang University
7 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73  (11) , 7852-7863
A Current-Balanced Analog Frontend System With Adaptive Input Voltage for Multiple Cell Li-ion Battery Electrochemical Impedance Monitoring
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73  (11) , 7852-7863
A Current-Balanced Analog Frontend System With Adaptive Input Voltage for Multiple Cell Li-ion Battery Electrochemical Impedance Monitoring
- 24 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP  (00189200) , 1-13
An Energy Efficient Amplifier With a Closed-Loop G m -Boosting Stage and Current-Mirror-Based SR Enhancement for Driving Large Capacitive Loads
This article proposes a low-power two-stage amplifier for large capacitive load driving. A closed-loop $g_{\text{m}}$ -boosting (CLGB) stage with complementary driving devices is exploited to reduce the output resistance, and thus, makes the output pole non-dominant with minimum power overhead. Therefore, the amplifier has the dominant pole internally with a small capacitor, achieving a high gain-bandwidth (GBW). Meanwhile, a current-mirror-based slew rate (SR) enhancement circuit is implemented to increase the current driving capability. This circuit leverages the gain of a cross-coupled pair to generate an SR-enhancing current with a fixed ratio to its bias, featuring high PVT robustness compared with voltage-based enhancement. The proposed amplifier is implemented in a standard 55-nm CMOS technology, with an active area of 0.009 mm2. It achieves a GBW of 1.6 MHz with a 12-nF $C_{\mathrm {L}}$ , achieving an IFoMS of 9 84 615 that advances the state of the art by $1.4\times $ . It provides an SR of 0.19V/ $\mu $ s with a 12-nF load, with an IFoML of 1 16 923, exceeding the state of the art by $2\times $ . The excellent GBW and SR with a quiescent current of only 19.5 $\mu $ A make this amplifier suitable for large capacitance driving applications.
- 24 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP  (00189200) , 1-13
An Energy Efficient Amplifier With a Closed-Loop G m -Boosting Stage and Current-Mirror-Based SR Enhancement for Driving Large Capacitive Loads
This article proposes a low-power two-stage amplifier for large capacitive load driving. A closed-loop $g_{\text{m}}$ -boosting (CLGB) stage with complementary driving devices is exploited to reduce the output resistance, and thus, makes the output pole non-dominant with minimum power overhead. Therefore, the amplifier has the dominant pole internally with a small capacitor, achieving a high gain-bandwidth (GBW). Meanwhile, a current-mirror-based slew rate (SR) enhancement circuit is implemented to increase the current driving capability. This circuit leverages the gain of a cross-coupled pair to generate an SR-enhancing current with a fixed ratio to its bias, featuring high PVT robustness compared with voltage-based enhancement. The proposed amplifier is implemented in a standard 55-nm CMOS technology, with an active area of 0.009 mm2. It achieves a GBW of 1.6 MHz with a 12-nF $C_{\mathrm {L}}$ , achieving an IFoMS of 9 84 615 that advances the state of the art by $1.4\times $ . It provides an SR of 0.19V/ $\mu $ s with a 12-nF load, with an IFoML of 1 16 923, exceeding the state of the art by $2\times $ . The excellent GBW and SR with a quiescent current of only 19.5 $\mu $ A make this amplifier suitable for large capacitance driving applications.
- 11 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61  (3) , 898-911
A High-Precision Level-Crossing Pipelined ADC With Trigger-Sampled Backend Stage
This article presents a high-precision level-crossing (LC) pipelined analog-to-digital converter (ADC) for sparse signal processing, addressing the critical resolution challenge in conventional LC architecture. A triggered sampling technique is proposed to eliminate the misalignment between the output timestamp and the output voltage amplitude in conventional continuous-time (CT) LC ADCs, which is achieved by sampling the input signal according to the triggering signal from a4-bit LC detector. Moreover, the signal-dependent error caused by the inevitable CT comparator delay is thus accurately extracted by feeding back the LC output codes. A $16{\times }$ redundancy-free residue amplifier (RA), followed by an 8-bit second-stage successive approximation register (SAR) ADC, is adopted to perform finer quantization and improve the resolution. Fabricated in a55-nm CMOS process, the prototype ADC achieves a measured peak SNDR of 72.5 dB with a 6.6-kHz input under a 1-V supply, achieving the highest reported SNDR and providing an 8-dB improvement over state-of-the-art. Also, thanks to the LC scheme, the proposed ADC demonstrates a dynamic power consumption from $1.2~{\mu }$ W (static) to $11.8~{\mu }$ W (20-kHz input), yielding Walden FoM (FoM w ) of 9–86 fJ/conv.step.
- 11 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61  (3) , 898-911
A High-Precision Level-Crossing Pipelined ADC With Trigger-Sampled Backend Stage
This article presents a high-precision level-crossing (LC) pipelined analog-to-digital converter (ADC) for sparse signal processing, addressing the critical resolution challenge in conventional LC architecture. A triggered sampling technique is proposed to eliminate the misalignment between the output timestamp and the output voltage amplitude in conventional continuous-time (CT) LC ADCs, which is achieved by sampling the input signal according to the triggering signal from a4-bit LC detector. Moreover, the signal-dependent error caused by the inevitable CT comparator delay is thus accurately extracted by feeding back the LC output codes. A $16{\times }$ redundancy-free residue amplifier (RA), followed by an 8-bit second-stage successive approximation register (SAR) ADC, is adopted to perform finer quantization and improve the resolution. Fabricated in a55-nm CMOS process, the prototype ADC achieves a measured peak SNDR of 72.5 dB with a 6.6-kHz input under a 1-V supply, achieving the highest reported SNDR and providing an 8-dB improvement over state-of-the-art. Also, thanks to the LC scheme, the proposed ADC demonstrates a dynamic power consumption from $1.2~{\mu }$ W (static) to $11.8~{\mu }$ W (20-kHz input), yielding Walden FoM (FoM w ) of 9–86 fJ/conv.step.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73  (4) , 2254-2267
A Piezoelectric Energy-Harvesting Sensor Interface IC With High-Efficient Power Management and Readout Circuitry for Structural Health Monitoring
A vibration piezoelectric energy-harvesting (PEH) sensor interface IC including high-efficiency power management and readout circuit for structural health monitoring is presented in this paper. The PEH interface consists of a parallel synchronized switched harvesting on inductor (SSHI) rectifier, and a novel duty cycle based maximum power point tracking (MPPT) circuit implemented with comparators and a switched capacitor. The comparators in both the SSHI and MPPT controllers are dynamically biased to provide fast response with low power. The switched capacitor based MPPT can tune the output voltage to suit the input effectively with a simple circuit structure. Moreover, the vibration frequency can be monitored to wake up the readout circuit when a certain threshold (20 Hz) is surpassed, indicating a possible catastrophic event. The readout circuit includes a low-power amplifier with dynamic bias, providing a programmable gain of 4/8/32/128 for the following 12-bit SAR ADC. The proposed system is implemented in a 55 nm standard CMOS technology. Experimental results show that a peak MPPT efficiency of 98.7% and up to 711% output power enhancement are achieved at 133 Hz resonance frequency. Moreover, the event driven wake-up of the readout circuit is successfully demonstrated. With a 11.3-bit ENOB achieved in the SAR ADC, the vibration frequency, temperature, and strain can be extracted from the proposed interface IC.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73  (4) , 2254-2267
A Piezoelectric Energy-Harvesting Sensor Interface IC With High-Efficient Power Management and Readout Circuitry for Structural Health Monitoring
A vibration piezoelectric energy-harvesting (PEH) sensor interface IC including high-efficiency power management and readout circuit for structural health monitoring is presented in this paper. The PEH interface consists of a parallel synchronized switched harvesting on inductor (SSHI) rectifier, and a novel duty cycle based maximum power point tracking (MPPT) circuit implemented with comparators and a switched capacitor. The comparators in both the SSHI and MPPT controllers are dynamically biased to provide fast response with low power. The switched capacitor based MPPT can tune the output voltage to suit the input effectively with a simple circuit structure. Moreover, the vibration frequency can be monitored to wake up the readout circuit when a certain threshold (20 Hz) is surpassed, indicating a possible catastrophic event. The readout circuit includes a low-power amplifier with dynamic bias, providing a programmable gain of 4/8/32/128 for the following 12-bit SAR ADC. The proposed system is implemented in a 55 nm standard CMOS technology. Experimental results show that a peak MPPT efficiency of 98.7% and up to 711% output power enhancement are achieved at 133 Hz resonance frequency. Moreover, the event driven wake-up of the readout circuit is successfully demonstrated. With a 11.3-bit ENOB achieved in the SAR ADC, the vibration frequency, temperature, and strain can be extracted from the proposed interface IC.
- 24 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72  (11) , 6493-6504
Constant Off-Time-Based Current-Balancing Technique With Accuracy and Transient Optimization in Wide I/O Range for Multi-Phase Regulator
A constant off-time (COFT) based current-balancing (CB) technique is proposed for integrated multi-phase DC-DC switching regulators with wide input/output (I/O) voltage range. The small-signal characteristics and design criteria of the proposed technique are derived based on describing functions. The current-balancing accuracy of the proposed technique depends merely on the ratio between the sensing FETs and the corresponding power switches ($\alpha $ ), while the requirement on absolute equivalent sensing-resistances ($R_{\mathrm {i}}$ ) and the matching of sensing circuits among phases are relaxed. Meanwhile, both the proposed current-balancing behavior and the adjustment of phase number will not affect the stability and the transient behavior of the multi-phase system. Furthermore, as a crucial block of the COFT control scheme, the proposed self-tuning PLLs of clock synchronization loop can remain fixed bandwidth under different I/O voltages, which further enhance the system stability. Therefore, in principle, the phase-interleaving with fixed switching frequency can be realized without the limit of duty cycle. As a result, the proposed CB technique can alleviate the stringent matching requirement of layout in conventional multi-phase systems, as well as the loop compensation difficulty. It is verified by an integrated dual-phase regulator fabricated in a$0.18\mu $ m BCD process. Experimental results show that the regulator can provide 0.9-1.8V output from a 2.3-5.5V input at both steady state and load-transient state with significantly higher performance by the proposed CB technique, ensuring current-imbalance ratio within ±1.3%.- 24 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72  (11) , 6493-6504
Constant Off-Time-Based Current-Balancing Technique With Accuracy and Transient Optimization in Wide I/O Range for Multi-Phase Regulator
A constant off-time (COFT) based current-balancing (CB) technique is proposed for integrated multi-phase DC-DC switching regulators with wide input/output (I/O) voltage range. The small-signal characteristics and design criteria of the proposed technique are derived based on describing functions. The current-balancing accuracy of the proposed technique depends merely on the ratio between the sensing FETs and the corresponding power switches ($\alpha $ ), while the requirement on absolute equivalent sensing-resistances ($R_{\mathrm {i}}$ ) and the matching of sensing circuits among phases are relaxed. Meanwhile, both the proposed current-balancing behavior and the adjustment of phase number will not affect the stability and the transient behavior of the multi-phase system. Furthermore, as a crucial block of the COFT control scheme, the proposed self-tuning PLLs of clock synchronization loop can remain fixed bandwidth under different I/O voltages, which further enhance the system stability. Therefore, in principle, the phase-interleaving with fixed switching frequency can be realized without the limit of duty cycle. As a result, the proposed CB technique can alleviate the stringent matching requirement of layout in conventional multi-phase systems, as well as the loop compensation difficulty. It is verified by an integrated dual-phase regulator fabricated in a$0.18\mu $ m BCD process. Experimental results show that the regulator can provide 0.9-1.8V output from a 2.3-5.5V input at both steady state and load-transient state with significantly higher performance by the proposed CB technique, ensuring current-imbalance ratio within ±1.3%.- 25 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33  (6) , 1784-1788
A 1 mW–10 W, Over 86.4% Efficiency Tri-Mode Buck Converter With Ripple-Based Control for Mobile Applications
To achieve high efficiency over wide load range for modern mobile applications, this brief proposes a ripple-based V2-controlled buck converter operating with pulsewidth modulation (PWM)/pulse-frequency modulation (PFM)/load-adaptive standby mode (LASM). On system level, a delay-based load-adaptive Von generator is exploited in LASM at ultralight load. When the output ripple is kept below its maximum restriction, the switching loss of the converter is further minimized in LASM compared with prior operation modes, including PFM, pulse-skip modulation (PSM), multiple-sawtooth PWM (MSPWM), and deep green mode (DGM). On circuit level, a dynamic-biased dual-offset hysteresis comparator is proposed. Together with other blocks that can be disabled, the quiescent consumption of controller in LASM is reduced to only 14 μW. Fabricated in a 130-nm BCD process, the proposed converter can provide a 1.8-V output with a power density of 4.11 W/mm2. It achieves a 93.2% peak efficiency, while the efficiency can be maintained above 86.4% in 1 mW–10 W (×10 000) load range.
- 25 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33  (6) , 1784-1788
A 1 mW–10 W, Over 86.4% Efficiency Tri-Mode Buck Converter With Ripple-Based Control for Mobile Applications
To achieve high efficiency over wide load range for modern mobile applications, this brief proposes a ripple-based V2-controlled buck converter operating with pulsewidth modulation (PWM)/pulse-frequency modulation (PFM)/load-adaptive standby mode (LASM). On system level, a delay-based load-adaptive Von generator is exploited in LASM at ultralight load. When the output ripple is kept below its maximum restriction, the switching loss of the converter is further minimized in LASM compared with prior operation modes, including PFM, pulse-skip modulation (PSM), multiple-sawtooth PWM (MSPWM), and deep green mode (DGM). On circuit level, a dynamic-biased dual-offset hysteresis comparator is proposed. Together with other blocks that can be disabled, the quiescent consumption of controller in LASM is reduced to only 14 μW. Fabricated in a 130-nm BCD process, the proposed converter can provide a 1.8-V output with a power density of 4.11 W/mm2. It achieves a 93.2% peak efficiency, while the efficiency can be maintained above 86.4% in 1 mW–10 W (×10 000) load range.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60  (6) , 2084-2095
A 93.6-dB SNDR Fully Dynamic CT-DT Noise-Shaping SAR ADC With Closed-Loop Capacitively Coupled Two-Stage FIA
This article presents an embedded-friendly high-precision two-step noise-shaping (NS) successive approximation register (SAR) analog-to-digital converter (ADC) designed for sensor applications. By employing a continuous-time (CT) SAR to track the input signal, the design avoids the kT/C noise typically induced by sampling operations. This approach decouples the signal-to-noise ratio (SNR) from the size of the sampling capacitor, thus relaxing the burden of the input and reference buffers. The CT SAR is followed by a two-stage floating-inverter-amplifier (FIA)-based closed-loop residue amplifier (RA) with a 94.6-dB open-loop gain, effectively mitigating interstage gain error. Furthermore, the CT–DT NS SAR exhibits high energy efficiency and fully dynamic characteristics due to the proposed RA and the second-stage DT NS SAR. Fabricated in a 55-nm CMOS process, the prototype achieves a signal-to-noise and distortion ratio (SNDR) of 93.6 dB with only a 120-fF single-ended input capacitor at a signal bandwidth of 5 kHz. Operating at a 1-MHz operating rate, the prototype consumes 34.7 $\mu$ W from a 1.2-V supply, resulting in a Schreier figure of merit (FoM) of 175.2 dB.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60  (6) , 2084-2095
A 93.6-dB SNDR Fully Dynamic CT-DT Noise-Shaping SAR ADC With Closed-Loop Capacitively Coupled Two-Stage FIA
This article presents an embedded-friendly high-precision two-step noise-shaping (NS) successive approximation register (SAR) analog-to-digital converter (ADC) designed for sensor applications. By employing a continuous-time (CT) SAR to track the input signal, the design avoids the kT/C noise typically induced by sampling operations. This approach decouples the signal-to-noise ratio (SNR) from the size of the sampling capacitor, thus relaxing the burden of the input and reference buffers. The CT SAR is followed by a two-stage floating-inverter-amplifier (FIA)-based closed-loop residue amplifier (RA) with a 94.6-dB open-loop gain, effectively mitigating interstage gain error. Furthermore, the CT–DT NS SAR exhibits high energy efficiency and fully dynamic characteristics due to the proposed RA and the second-stage DT NS SAR. Fabricated in a 55-nm CMOS process, the prototype achieves a signal-to-noise and distortion ratio (SNDR) of 93.6 dB with only a 120-fF single-ended input capacitor at a signal bandwidth of 5 kHz. Operating at a 1-MHz operating rate, the prototype consumes 34.7 $\mu$ W from a 1.2-V supply, resulting in a Schreier figure of merit (FoM) of 175.2 dB.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72  (4) , 1510-1521
An 871 nW 96.2 dB SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier
This article presents a two-stage pipelined noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converters (ADCs) for sub-micro-watt and high-resolution applications. However, it asks for an accurate residue amplification to avoid severe quantization noise leakage from the frontend stage. Therefore, a charge-efficient correlated-level-shifting (CECLS) assisted residue amplifier (RA) is designed by inserting the level-shifting network (LSN) in a two-stage floating inverter amplifier (FIA). In addition to the inherited low-power merit from FIA, it boosts the equivalent open-loop gain to 92 dB while preventing bandwidth reduction and charge-sharing effects, making the amplification more accurate and faster than prior CLS-assisted amplifiers. The prototype is fabricated using 55 nm CMOS technology and occupies an active area of 0.26 mm $^{\mathbf{2}}$ . The measurement results show a 96.2 dB peak-SNDR and 871 nW power consumption under a 1.2 V supply voltage with a 16 kS/s sampling rate. Compared to the recent state-of-the-art ADCs with power under 10 $\mu$ W and SNDR exceeding 90 dB, this ADC presents the best Schreier FoM of 180.8 dB.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72  (4) , 1510-1521
An 871 nW 96.2 dB SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier
This article presents a two-stage pipelined noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converters (ADCs) for sub-micro-watt and high-resolution applications. However, it asks for an accurate residue amplification to avoid severe quantization noise leakage from the frontend stage. Therefore, a charge-efficient correlated-level-shifting (CECLS) assisted residue amplifier (RA) is designed by inserting the level-shifting network (LSN) in a two-stage floating inverter amplifier (FIA). In addition to the inherited low-power merit from FIA, it boosts the equivalent open-loop gain to 92 dB while preventing bandwidth reduction and charge-sharing effects, making the amplification more accurate and faster than prior CLS-assisted amplifiers. The prototype is fabricated using 55 nm CMOS technology and occupies an active area of 0.26 mm $^{\mathbf{2}}$ . The measurement results show a 96.2 dB peak-SNDR and 871 nW power consumption under a 1.2 V supply voltage with a 16 kS/s sampling rate. Compared to the recent state-of-the-art ADCs with power under 10 $\mu$ W and SNDR exceeding 90 dB, this ADC presents the best Schreier FoM of 180.8 dB.
- Open Access
- 29 September 2024
- Published by MDPI AG in Electronics
- Vol. 13  (19) , 3865
An 88 dB SNDR 100 kHz BW Sturdy MASH Delta-Sigma Modulator Using Self-Cascoded Floating Inverter Amplifiers
Battery-powered Internet-of-Things applications require high-resolution, energy-efficient analog-to-digital converters (ADCs). There are still limited works on sub-MHz-bandwidth ADC designs. This paper presents a sturdy multi-stage shaping (SMASH) discrete-time (DT) delta-sigma modulator (DSM) structure using a self-cascoded floating-inverter-based dynamic amplifier (FIA). The proposed structure removes the explicit quantization error extraction of the first loop and all the feedback DACs in the cascaded loop, decreasing the design complexity of the circuit. This enables the proposed DT DSM to operate at a higher speed, which is suitable for achieving high-order noise at a low oversampling ratio (OSR). The proposed self-cascoded FIA is more power-efficient and can acquire more than 45 dB DC gain under a 1.2 V supply. The DT DSM implemented in a piece of 55 nm CMOS technology measures an 88.0 dB peak signal-to-noise-and-distortion ratio (SNDR) in a 100 kHz bandwidth (BW) and an 85.3 dB dynamic range (DR), consuming 249.1 μW from a 1.2 V supply at 10 MS/s. The obtained 174.0 dB SNDR-based Schreier figure-of-merit (FoMs) is competitive within state-of-art high-resolution (SNDR > 85 dB) and general-purpose (sub-MHz-bandwidth) ΔΣ ADCs.
- 29 September 2024
- Published by MDPI AG in Electronics
- Vol. 13  (19) , 3865
Open AccessAn 88 dB SNDR 100 kHz BW Sturdy MASH Delta-Sigma Modulator Using Self-Cascoded Floating Inverter Amplifiers
Battery-powered Internet-of-Things applications require high-resolution, energy-efficient analog-to-digital converters (ADCs). There are still limited works on sub-MHz-bandwidth ADC designs. This paper presents a sturdy multi-stage shaping (SMASH) discrete-time (DT) delta-sigma modulator (DSM) structure using a self-cascoded floating-inverter-based dynamic amplifier (FIA). The proposed structure removes the explicit quantization error extraction of the first loop and all the feedback DACs in the cascaded loop, decreasing the design complexity of the circuit. This enables the proposed DT DSM to operate at a higher speed, which is suitable for achieving high-order noise at a low oversampling ratio (OSR). The proposed self-cascoded FIA is more power-efficient and can acquire more than 45 dB DC gain under a 1.2 V supply. The DT DSM implemented in a piece of 55 nm CMOS technology measures an 88.0 dB peak signal-to-noise-and-distortion ratio (SNDR) in a 100 kHz bandwidth (BW) and an 85.3 dB dynamic range (DR), consuming 249.1 μW from a 1.2 V supply at 10 MS/s. The obtained 174.0 dB SNDR-based Schreier figure-of-merit (FoMs) is competitive within state-of-art high-resolution (SNDR > 85 dB) and general-purpose (sub-MHz-bandwidth) ΔΣ ADCs.