MZMenglian Zhao

Menglian Zhao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Menglian Zhao has a total of 107 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis and Design of RC-Variation-Robust Continuous-Time Delta-Sigma Modulator with Boosted MSA

    by Zhaonan Lu, Junqi Liu, Liang Qi, Menglian Zhao, Zhichao Tan

    Continuous-time delta-sigma modulators (CT DSMs) have been widely adopted in IoT and sensor applications. Despite the merits of the inherent anti-alias property and easy-driving resistive input, CT DSMs always suffer from the RC variation issue. While a higher maximum stable amplitude (MSA) can result in a higher dynamic range (DR) with better efficiency, it is often limited to -1 dBFS. To address the above issues, this article presents a hybrid 1-2 sturdy multi-stage noise-shaping (MASH) architecture that exhibits high robustness against RC variations. The proposed modulator integrates a first-order RC-variation-insensitive CT loop filter with a second-order noise-shaping (NS) successive approximation register (SAR) quantizer. By leveraging the inherent unity signal transfer function (STF) of the NS-SAR quantizer, the quantization noise of the first stage is effectively canceled without requiring analog-digital matching. This enables the modulator to achieve a beyond-the-rail MSA while performing aggressive third-order NS. Fabricated in a 55-nm CMOS process, the prototype achieves a measured signal-to-noise-and-distortion ratio (SNDR) of 89.1 dB and a DR of 95.3 dB over a signal bandwidth of 100 kHz, while consuming 459 μW from a single 1.2-V supply. These results yield a state-of-the-art Schreier figure of merit of 178.7 dB among prior art with similar bandwidth. Additionally, the prototype demonstrates robust performance across a wide range of temperatures.

  • The Regulated Resonant Sigma Converter: A Hybrid Topology With Balanced Efficiency, Speed, and Density

    by Yukan Du, Shengdao Ren, Zheyuan Fei, Ziteng Chen, Menglian Zhao, Chushan Li, Yong Ding, Wuhua Li, Zhichao Tan, Wanyuan Qu

  • An Energy Efficient Amplifier With a Closed-Loop G m -Boosting Stage and Current-Mirror-Based SR Enhancement for Driving Large Capacitive Loads

    by Siyao Cao, Mengyu Li, Dehong Wang, Qiuyang Lin, Kai Huang, Zhichao Tan, Menglian Zhao, Shuang Song

    This article proposes a low-power two-stage amplifier for large capacitive load driving. A closed-loop $g_{\text{m}}$ -boosting (CLGB) stage with complementary driving devices is exploited to reduce the output resistance, and thus, makes the output pole non-dominant with minimum power overhead. Therefore, the amplifier has the dominant pole internally with a small capacitor, achieving a high gain-bandwidth (GBW). Meanwhile, a current-mirror-based slew rate (SR) enhancement circuit is implemented to increase the current driving capability. This circuit leverages the gain of a cross-coupled pair to generate an SR-enhancing current with a fixed ratio to its bias, featuring high PVT robustness compared with voltage-based enhancement. The proposed amplifier is implemented in a standard 55-nm CMOS technology, with an active area of 0.009 mm2. It achieves a GBW of 1.6 MHz with a 12-nF $C_{\mathrm {L}}$ , achieving an IFoMS of 9 84 615 that advances the state of the art by $1.4\times $ . It provides an SR of 0.19V/ $\mu $ s with a 12-nF load, with an IFoML of 1 16 923, exceeding the state of the art by $2\times $ . The excellent GBW and SR with a quiescent current of only 19.5 $\mu $ A make this amplifier suitable for large capacitance driving applications.

  • A High-Precision Level-Crossing Pipelined ADC With Trigger-Sampled Backend Stage

    by Zexin Wang, Lingxin Meng, Menglian Zhao, Mengyu Li, Shuang Song, Zhangming Zhu, Zhichao Tan

    This article presents a high-precision level-crossing (LC) pipelined analog-to-digital converter (ADC) for sparse signal processing, addressing the critical resolution challenge in conventional LC architecture. A triggered sampling technique is proposed to eliminate the misalignment between the output timestamp and the output voltage amplitude in conventional continuous-time (CT) LC ADCs, which is achieved by sampling the input signal according to the triggering signal from a4-bit LC detector. Moreover, the signal-dependent error caused by the inevitable CT comparator delay is thus accurately extracted by feeding back the LC output codes. A $16{\times }$ redundancy-free residue amplifier (RA), followed by an 8-bit second-stage successive approximation register (SAR) ADC, is adopted to perform finer quantization and improve the resolution. Fabricated in a55-nm CMOS process, the prototype ADC achieves a measured peak SNDR of 72.5 dB with a 6.6-kHz input under a 1-V supply, achieving the highest reported SNDR and providing an 8-dB improvement over state-of-the-art. Also, thanks to the LC scheme, the proposed ADC demonstrates a dynamic power consumption from $1.2~{\mu }$ W (static) to $11.8~{\mu }$ W (20-kHz input), yielding Walden FoM (FoM w ) of 9–86 fJ/conv.step.

  • A 15-bit BW/Power Scalable Pseudo-Pseudo-Differential MASH ADC Using an Adaptively Biased Inverter Amplifier

    by Zhenhao Fan, Zhaonan Lu, Menglian Zhao, Wanyuan Qu, Zhichao Tan

    This brief presents an inverter amplifier-based dynamic pseudo-pseudo-differential (PPD) multistage noise-shaping (MASH) analog-to-digital converter (ADC) for sensor interface applications. To enable the bandwidth (BW)/power scalability of single-ended topology-based delta-sigma modulators, an adaptively biased inverter amplifier (ABIA) is proposed, whose power consumption varies with sampling frequency (fS). A 3-0 MASH structure is employed to maintain a high signal-to-quantization-noise ratio (SQNR). Fabricated in 55 nm CMOS technology, the proposed ADC achieves a 15-bit ENOB over 60× BW scaling, from 28 Hz to 1700 Hz, with power consumption ranging from 255 nW to 3.29 μW, thanks to the adaptive biasing scheme. Furthermore, the ADC supports a wide input CM voltage range of 0.1 V to 1.5 V, with a signal-to-noise-and-distortion ratio (SNDR) variation of less than 3 dB. It achieves a Schreier figure-of-merit (FoM) of 178 dB and a Walden FoM of 34.6 fJ/step at 222 kHz fS.


  • A Piezoelectric Energy-Harvesting Sensor Interface IC With High-Efficient Power Management and Readout Circuitry for Structural Health Monitoring

    by Dehong Wang, Mengyu Li, Siyao Cao, Yulu Zhang, Jiankao Pan, Kai Huang, Sijun Du, Zhichao Tan, Menglian Zhao, Shuang Song

    A vibration piezoelectric energy-harvesting (PEH) sensor interface IC including high-efficiency power management and readout circuit for structural health monitoring is presented in this paper. The PEH interface consists of a parallel synchronized switched harvesting on inductor (SSHI) rectifier, and a novel duty cycle based maximum power point tracking (MPPT) circuit implemented with comparators and a switched capacitor. The comparators in both the SSHI and MPPT controllers are dynamically biased to provide fast response with low power. The switched capacitor based MPPT can tune the output voltage to suit the input effectively with a simple circuit structure. Moreover, the vibration frequency can be monitored to wake up the readout circuit when a certain threshold (20 Hz) is surpassed, indicating a possible catastrophic event. The readout circuit includes a low-power amplifier with dynamic bias, providing a programmable gain of 4/8/32/128 for the following 12-bit SAR ADC. The proposed system is implemented in a 55 nm standard CMOS technology. Experimental results show that a peak MPPT efficiency of 98.7% and up to 711% output power enhancement are achieved at 133 Hz resonance frequency. Moreover, the event driven wake-up of the readout circuit is successfully demonstrated. With a 11.3-bit ENOB achieved in the SAR ADC, the vibration frequency, temperature, and strain can be extracted from the proposed interface IC.


  • A Two-Stage 12–1-V Converter Featuring Regulated Resonant SC Regulators and Collaborative Control Scheme

    by Shengdao Ren, Yukan Du, Menglian Zhao, Zhichao Tan, Chushan Li, Yong Ding, Wuhua Li, Wanyuan Qu

    In the field of power converters for data centers, the two-stage architecture has received widespread attentions due to its various advantages. Especially, the switched-capacitor voltage regulator (SCVR) becomes popular as the second-stage converter owing to its high efficiency and power density. However, the SCVR suffers from poor voltage regulation and limited load capacity. To address these limitations, this article presents a two-stage converter featuring a regulated resonant switched-capacitor (ReSC) second-stage design. Thanks to the resonant operation of the ReSC, the converter achieves the superior power density and load capacity using a compact sub-nano-henry trace inductor. In addition, the resonant operation paves way for the voltage regulation, which is further employed for enhancing transient performances. Finally, to overcome the inherent efficiency versus voltage regulation tradeoff for the ReSC, a collaborative control scheme is built between the first and second stages, which adaptively adjusts the intermediate bus voltage to maintain the ReSC always in the efficient non-regulation mode for the entire output voltage range, leading to a high efficiency for a wide voltage and current range. By employing discrete GaNFETs for the first stage and 65-nm CMOS technology for the ReSC and controller design, the proposed two-stage converter achieves a measured system peak efficiency of 89.3% for 12:1-V conversion. With a 4-A/20-ns load current step, the measured undershoot voltage is 26 mV.


  • Constant Off-Time-Based Current-Balancing Technique With Accuracy and Transient Optimization in Wide I/O Range for Multi-Phase Regulator

    by Shuyu Zhang, Menglian Zhao, Shuang Song

    A constant off-time (COFT) based current-balancing (CB) technique is proposed for integrated multi-phase DC-DC switching regulators with wide input/output (I/O) voltage range. The small-signal characteristics and design criteria of the proposed technique are derived based on describing functions. The current-balancing accuracy of the proposed technique depends merely on the ratio between the sensing FETs and the corresponding power switches ( $\alpha $ ), while the requirement on absolute equivalent sensing-resistances ( $R_{\mathrm {i}}$ ) and the matching of sensing circuits among phases are relaxed. Meanwhile, both the proposed current-balancing behavior and the adjustment of phase number will not affect the stability and the transient behavior of the multi-phase system. Furthermore, as a crucial block of the COFT control scheme, the proposed self-tuning PLLs of clock synchronization loop can remain fixed bandwidth under different I/O voltages, which further enhance the system stability. Therefore, in principle, the phase-interleaving with fixed switching frequency can be realized without the limit of duty cycle. As a result, the proposed CB technique can alleviate the stringent matching requirement of layout in conventional multi-phase systems, as well as the loop compensation difficulty. It is verified by an integrated dual-phase regulator fabricated in a $0.18\mu $ m BCD process. Experimental results show that the regulator can provide 0.9-1.8V output from a 2.3-5.5V input at both steady state and load-transient state with significantly higher performance by the proposed CB technique, ensuring current-imbalance ratio within ±1.3%.


  • A 1 mW–10 W, Over 86.4% Efficiency Tri-Mode Buck Converter With Ripple-Based Control for Mobile Applications

    by Shuyu Zhang, Menglian Zhao, Shuang Song

    To achieve high efficiency over wide load range for modern mobile applications, this brief proposes a ripple-based V2-controlled buck converter operating with pulsewidth modulation (PWM)/pulse-frequency modulation (PFM)/load-adaptive standby mode (LASM). On system level, a delay-based load-adaptive Von generator is exploited in LASM at ultralight load. When the output ripple is kept below its maximum restriction, the switching loss of the converter is further minimized in LASM compared with prior operation modes, including PFM, pulse-skip modulation (PSM), multiple-sawtooth PWM (MSPWM), and deep green mode (DGM). On circuit level, a dynamic-biased dual-offset hysteresis comparator is proposed. Together with other blocks that can be disabled, the quiescent consumption of controller in LASM is reduced to only 14 μW. Fabricated in a 130-nm BCD process, the proposed converter can provide a 1.8-V output with a power density of 4.11 W/mm2. It achieves a 93.2% peak efficiency, while the efficiency can be maintained above 86.4% in 1 mW–10 W (×10 000) load range.