Wanglin Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wanglin Chen has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Wanglin Chen
Guangdong University of Technology
2 shared publicationsBingxi Li
Guangdong Univ Technol, State Key Lab High Performance Tools, Guangzhou 510006, Peoples R China
1 shared publicationDaoda Zhang
Jiangxi Mechanical Scientific Institute, Nanchang City, PR China
1 shared publication- Daoda Zhang
School of Materials Science and Engineering, East China Jiaotong University, Nanchang 330013, China
1 shared publication Daodao Zhang
Jiangxi Mech Sci Inst, Nanchang 330000, Jiangxi, Peoples R China
1 shared publicationDengcan Yao
Jiangxi Mechanical Scientific Institute, Nanchang City, PR China
1 shared publication
Latest Publications
- Open Access
Microstructure, Elevated-Temperature Tribological Properties and Electrochemical Behavior of HVOF-Sprayed Composite Coatings with Varied NiCr/Cr3C2 Ratios and CoCrFeNiMo Additions
This study fabricated six types of NiCr–Cr3C2 composite coatings using high-velocity oxygen fuel (HVOF) spraying and systematically evaluated their tribological behavior at 350 °C and 500 °C, along with their electrochemical corrosion performance in 3.5 wt.% NaCl solution. The objective was to elucidate how compositional design regulates the coatings’ microstructure, mechanical properties, and service performance. Results indicate that the 75NiCr–25Cr3C2 coating (C) formed a stable oxide film under both temperatures, exhibiting oxidation-dominated wear and the lowest friction coefficient and wear rate. When the temperature increased from 350 °C to 500 °C, the wear rates of coatings C, B, E, and F decreased significantly. Notably, coatings E and F, which contained CoCrFeNiMo high-entropy alloy, showed more than a 50% reduction in wear rate, demonstrating the contribution of the high-entropy phase to high-temperature wear resistance. At 350 °C, coatings B, D, E, and F experienced primarily abrasive wear; at 500 °C, however, E and F shifted to oxidative wear as the dominant mechanism, leading to a marked improvement in wear resistance. Electrochemical measurements revealed that coating E exhibited the best corrosion resistance, while the NiCr coating (A) performed the worst. The findings highlight that optimizing Cr3C2 content and incorporating high-entropy alloy elements can synergistically enhance both high-temperature tribological properties and corrosion resistance.
Open AccessMicrostructure, Elevated-Temperature Tribological Properties and Electrochemical Behavior of HVOF-Sprayed Composite Coatings with Varied NiCr/Cr3C2 Ratios and CoCrFeNiMo Additions
This study fabricated six types of NiCr–Cr3C2 composite coatings using high-velocity oxygen fuel (HVOF) spraying and systematically evaluated their tribological behavior at 350 °C and 500 °C, along with their electrochemical corrosion performance in 3.5 wt.% NaCl solution. The objective was to elucidate how compositional design regulates the coatings’ microstructure, mechanical properties, and service performance. Results indicate that the 75NiCr–25Cr3C2 coating (C) formed a stable oxide film under both temperatures, exhibiting oxidation-dominated wear and the lowest friction coefficient and wear rate. When the temperature increased from 350 °C to 500 °C, the wear rates of coatings C, B, E, and F decreased significantly. Notably, coatings E and F, which contained CoCrFeNiMo high-entropy alloy, showed more than a 50% reduction in wear rate, demonstrating the contribution of the high-entropy phase to high-temperature wear resistance. At 350 °C, coatings B, D, E, and F experienced primarily abrasive wear; at 500 °C, however, E and F shifted to oxidative wear as the dominant mechanism, leading to a marked improvement in wear resistance. Electrochemical measurements revealed that coating E exhibited the best corrosion resistance, while the NiCr coating (A) performed the worst. The findings highlight that optimizing Cr3C2 content and incorporating high-entropy alloy elements can synergistically enhance both high-temperature tribological properties and corrosion resistance.
- 2 January 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (1) , 10-22
Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels
- 2 January 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (1) , 10-22
Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels
- 1 July 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 33 (7) , 536-541
Investigations on microstructure and mechanical properties of containing-Si coatings
Advanced AlCrSiN and AlTiSiN coatings were deposited on high-speed steel by cathodic vacuum arc. The microstructures, mechanical and tribological properties were studied, as well as cutting performance. The results show that multilayered AlCrSiN coating mainly consists of nanocrystalline fcc-AlCrN and a few amorphous Si3N4 phases, with an average module period of about 6.0 nm. While the AlTiSiN coating reveals nano-composite structure consisted of nanocrystalline fcc-AlTiN and hcp-AlN embedded into Si3N4 amorphous matrix. The AlCrSiN-coated tool reveals a more excellent cutting performance when compared with the AlTiSiN-coated tool due to its higher hardness, adhesion strength, H3/ E*2 ratio and wear resistance when compared with the AlTiSiN coating.
- 1 July 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 33 (7) , 536-541
Investigations on microstructure and mechanical properties of containing-Si coatings
Advanced AlCrSiN and AlTiSiN coatings were deposited on high-speed steel by cathodic vacuum arc. The microstructures, mechanical and tribological properties were studied, as well as cutting performance. The results show that multilayered AlCrSiN coating mainly consists of nanocrystalline fcc-AlCrN and a few amorphous Si3N4 phases, with an average module period of about 6.0 nm. While the AlTiSiN coating reveals nano-composite structure consisted of nanocrystalline fcc-AlTiN and hcp-AlN embedded into Si3N4 amorphous matrix. The AlCrSiN-coated tool reveals a more excellent cutting performance when compared with the AlTiSiN-coated tool due to its higher hardness, adhesion strength, H3/ E*2 ratio and wear resistance when compared with the AlTiSiN coating.
- 20 June 2016
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 25 (8) , 3472-3481
Effects of Ti and B Addition on Microstructures and Mechanical Properties of Hot-Rolled High-Strength Nb-Containing Steels
- 20 June 2016
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 25 (8) , 3472-3481
Effects of Ti and B Addition on Microstructures and Mechanical Properties of Hot-Rolled High-Strength Nb-Containing Steels