DCDong Chen

Dong Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Dong Chen has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Comparison of Two Typical Adhesive Fracture Mechanics Considering Hygrothermal Aging

    by Si Yu Li, Jun Wei Zhang, Dan Wang, Cheng Li, Jian Wei Shi, Dong Chen

    Carbon fiber reinforced polymer (CFRP) bonded structures are widely used for their lightweight and high specific strength. However, research on durability of adhesively bonded lap joints under hygrothermal conditions remain insufficient. Therefore, the aging process and residual strength of CFRP-bonded lap joints with different adhesives were studied. Condition of hygrothermal aging tests were set, then moisture absorption behavior of CFRP plate and adhesive layer were analyzed, respectively. Based on the same aging period, residual tensile strength of acrylic-based specimens and epoxy-based specimens were compared. To evaluate their performance and clarify the failure mechanisms, Finite element method (FEM) simulations were conducted. Load-displacement curve was recorded and morphology of the failure surfaces was analyzed by using a microscope.

  • Fracture Risk Modeling in Pyrolyzed Phenolic Resin: Microstructure Prediction and Stress Concentration Factor Evolution via CNN-CVAE and FEM

    by Wen Han Chen, Shu Hua Niu, Dan Wang, Cheng Li, Dong Chen, Jian Wei Shi

    The microstructure of phenolic resin undergoes significant transformation under high-temperature pyrolysis, affecting its mechanical performance and fracture behavior. By combining Convolutional Neural Networks (CNN) and Conditional Variational Autoencoders (CVAE), a generative modeling framework was proposed. Then its suitability to predict microstructure evolution of phenolic resin under varying pyrolysis temperatures was studied. Finite Element Method (FEM) simulations were conducted to analyze stress distributions. Results indicate a significant increase in the area of high stress concentration zones with rising pyrolysis temperature, with pore bridges, sharp edges, and clustered porosity identified as potential fracture initiation sites.

  • Research on Fracture Mechanics of Non-Reciprocal Adhesive in Composite Single-Lap Bonded Joints Based on UEL

    by Xin Qi Zhang, Dan Wang, Jia Zheng Wang, Jian Wei Shi, Dong Chen

    Single-lap bonded joints are widely used in aerospace, shipbuilding, and other fields due to their advantages, such as light weight, high specific strength, and no stress concentration caused by hole-making or spot-welding. However, the traditional methods of increasing geometric parameters, such as lap length to improve strength, have limitations in scenarios where the bonding area is restricted. To solve this problem, in this study, it is assumed that carbon fibers with a volume fraction of 10% were introduced into the epoxy adhesive layer and arranged in a 45° orientation. The mechanical non-reciprocity was achieved by utilizing the difference in tensile and compressive moduli. A non-reciprocal cohesive fracture mechanics model of the composite single-lap joint structure based on the User-defined Element (UEL) was established to explore the effect of non-reciprocity on the bonding strength. The results show that the non-reciprocal adhesive layer effectively suppresses the peeling stress concentration at the cohesive failure interface of the adhesive layer, increasing the tensile strength of the single-lap bonded joint by approximately 6.27% compared to the traditional homogeneous adhesive layer, verifying the effectiveness of the model. This research breaks through the limitations of traditional geometric parameter optimization. It can specifically regulate the interfacial stress distribution without changing the bonding area, providing a new material design idea for strength optimization in scenarios where the bonding area is restricted, such as in aerospace. It has important theoretical significance and engineering application prospects.

  • Study on Strength Optimization of CFRP Single-Lap Joints Based on Local Pre-Curing Effect

    by Jia Zheng Wang, Dan Wang, Xin Qi Zhang, Jian Wei Shi, Dong Chen

    The early failure of single-lap adhesive joints in carbon fiber reinforced polymer (CFRP) composites is typically induced by stress concentration at the edges of the overlap region. To address this issue, this study proposes a novel local pre-curing process system based on gradient thermal curing regulation. Through multi-physical field modeling of the temperature-curing coupling effect and a gradient curing control strategy, active optimization of the adhesive layer stress distribution is achieved. By optimizing the interface stress distribution, the proposed technique demonstrates the potential to enhance the overall joint performance by 3-6%. This research combines Abaqus finite element simulation and experimental verification. A CFRP single-lap joint model considering the temperature-curing coupling effect was established to analyze the influence of local pre-curing on the stress distribution of the adhesive layer. The results show that: 1. Local pre-curing can reduce the peel stress in the critical edge danger zone by about 3 - 5% while improving the shear strength in the middle region. 2. The preferential curing at the center of the adhesive layer can induce stress redistribution, relieve the stress concentration at the edges, and thus improve the overall load-bearing capacity of the joint. This study provides a low-cost and easily implementable solution for optimizing the performance of CFRP joints, showing potential applications in the field of lightweight aerospace structures. Through the synergistic effect of precise thermal management and regulation of the adhesive's rheological properties, it offers new insights for advanced composite joining technologies.

  • Open Access

    A Mixed-Integer Linear Programming Model for Addressing Efficient Flexible Flow Shop Scheduling Problem with Automatic Guided Vehicles Consideration

    by Dekun Wang, Hongxu Wu, Wengang Zheng, Yuhao Zhao, Guangdong Tian, Wenjie Wang, Dong Chen

    With the development of Industry 4.0, discrete manufacturing systems are accelerating their transformation toward flexibility and intelligence to meet the market demand for various products and small-batch production. The flexible flow shop (FFS) paradigm enhances production flexibility, but existing studies often address FFS scheduling and automated guided vehicle (AGV) path planning separately, resulting in resource competition conflicts, such as equipment idle time and AGV congestion, which prolong the manufacturing cycle time and reduce system energy efficiency. To solve this problem, this study proposes an integrated production–transportation scheduling framework (FFSP-AGV). By using the adjacent sequence modeling idea, a mixed-integer linear programming (MILP) model is established, which takes into account the constraints of the production process and AGV transportation task conflicts with the aim of minimizing the makespan and improving overall operational efficiency. Systematic evaluations are carried out on multiple test instances of different scales using the CPLEX solver. The results show that, for small-scale instances (job count ≤10), the MILP model can generate optimal scheduling solutions within a practical computation time (several minutes). Moreover, it is found that there is a significant marginal diminishing effect between AGV quantity and makespan reduction. Once the number of AGVs exceeds 60% of the parallel equipment capacity, their incremental contribution to cycle time reduction becomes much smaller. However, the computational complexity of the model increases exponentially with the number of jobs, making it slightly impractical for large-scale problems (job count > 20). This research highlights the importance of integrated production–transportation scheduling for reducing manufacturing cycle time and reveals a threshold effect in AGV resource allocation, providing a theoretical basis for collaborative optimization in smart factories.


  • Force analysis and distribution evolution of Fe3O4 nanoparticles in magnetic fluids

    by Kai Cui, Genghuan Song, Weichuan Wang, Huanying Liu, Yichuan Yang, Chaoqun Sun, Zhilong Zhao, Hongli Lin, Dong Chen


  • Open Access

    Efficiency Enhancement Strategies for Water-Source Thermoelectric Heat Pump Modules

    by Wei Zhu, Dong Chen, Jianwei Shi, Jingshuang Zhang, Zhinan Xu, Cheng Li

    Thermoelectric heat pump is a feasible solution for developing refrigerant-free technology, but most studies tend to focus more on cooling capacity. In this paper, a finite element model of the water-source thermoelectric heat pump module is established. By comparing the changes of the coefficient of performance (COPh) of the thermoelectric heat pump module under different pipe diameters(d), currents(I), temperatures(T), and temperature differences(∆T), the main parameters affecting the performance of the thermoelectric heat pump module are explored. Results show that: within the range of 20°C to 45°C, the influence of water temperature on COPh is relatively small under the same temperature difference; the heat output is not affected by the ∆T when I=7.17A, and the ∆T shows different trends in the left and right intervals: under the condition of large ∆T between the hot and cold ends of the module, there is an optimal working current, which increases with the increase of ∆T.Research has shown that I and ∆T are the main parameters affecting module performance. Under extreme operating conditions, using a specific value of current can simultaneously increase heating power and heating performance coefficient.

  • Impact damage assessment in patch‐repaired carbon fiber‐reinforced polymer laminates using the nonlinear Lamb wave‐mixing technique

    by Zhenhua Yin, Ying Tie, Yuechen Duan, Cheng Li, Dong Chen

    This study investigates assessment of the barely visible impact damage (BVID) caused by low‐velocity impact (LVI) in single‐sided patch‐repaired orthotropic carbon fiber‐reinforced polymer (CFRP) laminates using experimental and numerical nonlinear Lamb wave‐mixing techniques. An accurate finite element method (FEM) approach consisting of three analysis steps of LVI, vibration damping, and nonlinear ultrasonic mixing detection is proposed to predict the relationship between LVI damage and nonlinear Lamb wave‐mixing propagation. The LVI step in the FEM simulation is verified by drop‐weight impact tests, and the nonlinear Lamb wave‐mixing detection step in FEM is verified by comparing with the RITEC RAM‐5000 SNAP nonlinear mixing detection system. The BVID of patch‐repaired specimens is assessed with mixing relative acoustic nonlinearity parameters (MRANPs). CFRP laminates repaired with various external patch parameters of different sizes, numbers of layers and stacking sequences are evaluated by the FEM approach. Finally, an optimized patch design in which the MRANPs are the smallest is determined. Therefore, the CFRP laminate containing a hole is recommended to be repaired with a circular three‐layer patch with a radius of 2.5 r and a stacking sequence of [90/90/90].