Muammer Ermis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Muammer Ermis has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Işık Çadırcı
Electrical and Electronics Engineering Department, Hacettepe University, Beytepe Campus, TR06800 Ankara, Türkiye
8 shared publications - Dogan Yildirim
Department of Electrical and Electronics Engineering, Faculty of Engineering, Middle East Technical University, Ankara, Turkey
3 shared publications - Mehmet Hakan Aksit
Transportation, Security, Energy, Automation & Healthcare Systems Business Sector, ASELSAN Inc., Istiklal Marsi Caddesi No. 16, Yenimahalle, Ankara 06200, Türkiye
3 shared publications - Ozgul Salor
Electrical and Electronics Engineering, Gazi University, Ankara, Trkiye
3 shared publications Eda Uz-Logoglu
2 shared publicationsTuran Demirci
Power Electronics Department, TUBITAK Space Technologies Research Institute (TUBITAK UZAY) , Ankara, Turkey
2 shared publications
Latest Publications
- Open Access
A High-Performance Onboard Supercapacitor ESS with SiC Power MOSFET Buck–Boost Converter for Railway Applications
This paper is devoted to the design and implementation of a high-performance onboard Supercapacitor energy storage system (ESS) with a SiC power MOSFET-based buck–boost converter for railway applications. The SiC power MOSFET-based buck–boost converter can be switched at higher frequencies than those of Si-IGBT and Hybrid-IGBT counterparts, resulting in significant volume and cost reduction in the buck–boost inductor. A new operating strategy is proposed for a Supercapacitor ESS to optimize the electrical energy savings of a light rail transportation system (LRTS) while running on a prespecified rail track. In the Optimized Operating Strategy, regenerative braking torque and power profiles are pre-programmed before departing from each station to allow the storage of almost all of the kinetic energy of the vehicle in a Supercapacitor ESS. Details of the proposed Optimized Operating Strategy are described in a comparative manner with the Standard Operating Strategy in the paper. Furthermore, effects of the type of interface circuit between the DC catenary line and the AC grid are also discussed in view of the net energy consumption of the LRTS from the AC grid while operating on a typical rail track. All theoretical results are verified by experimental work conducted on a physical simulator. The results obtained show that an onboard Supercapacitor ESS with an Optimized Operating Strategy provides 36% energy savings with respect to the base case with no ESS of a railway vehicle moving on a prespecified track and supplied from a unidirectional interface circuit between the DC catenary and AC grid. This paper is accompanied by a video demonstrating the experimental work.
Open AccessA High-Performance Onboard Supercapacitor ESS with SiC Power MOSFET Buck–Boost Converter for Railway Applications
This paper is devoted to the design and implementation of a high-performance onboard Supercapacitor energy storage system (ESS) with a SiC power MOSFET-based buck–boost converter for railway applications. The SiC power MOSFET-based buck–boost converter can be switched at higher frequencies than those of Si-IGBT and Hybrid-IGBT counterparts, resulting in significant volume and cost reduction in the buck–boost inductor. A new operating strategy is proposed for a Supercapacitor ESS to optimize the electrical energy savings of a light rail transportation system (LRTS) while running on a prespecified rail track. In the Optimized Operating Strategy, regenerative braking torque and power profiles are pre-programmed before departing from each station to allow the storage of almost all of the kinetic energy of the vehicle in a Supercapacitor ESS. Details of the proposed Optimized Operating Strategy are described in a comparative manner with the Standard Operating Strategy in the paper. Furthermore, effects of the type of interface circuit between the DC catenary line and the AC grid are also discussed in view of the net energy consumption of the LRTS from the AC grid while operating on a typical rail track. All theoretical results are verified by experimental work conducted on a physical simulator. The results obtained show that an onboard Supercapacitor ESS with an Optimized Operating Strategy provides 36% energy savings with respect to the base case with no ESS of a railway vehicle moving on a prespecified track and supplied from a unidirectional interface circuit between the DC catenary and AC grid. This paper is accompanied by a video demonstrating the experimental work.
- 12 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 4778-4791
Selective Harmonic Elimination for Variable Frequency Traction Motor Drives Using Harris Hawks Optimization
In this paper, harris hawks optimization (HHO) for selective harmonic elimination method (SHEM) of a voltage source inverter has been applied to a traction motor drive for light rail transportation. The main objective of SHEM's pulse-width modulation strategy is to remove the low-order harmonics by solving nonlinear equations while satisfying the required fundamental component's magnitude. The HHO applied in this paper to a two-level, three-phase inverter aims at solving the associated nonlinear equations with a high accuracy and convergence probability as a strong metaheuristic algorithm. SHEM simulations are carried out via MATLAB / Simulink on a 125 kW traction motor drive platform for various SHEM angles to verify its performance in comparison with the SHEM with SPWM and SVM techniques. Experimental results obtained on a physical simulator of the light rail transportation system in the laboratory have shown remarkable findings in view of the DC link voltage magnitude on the performance of the associated traction motor drive. In the light of different fundamental frequency operations, the number of SHEM angles, and operating DC link voltages, a general evaluation of the SHEM has been made in considering its application to a light rail traction motor drive. It has also been shown that the application of online SHEM on a GPU framework is possible in real-time.
- 12 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 4778-4791
Selective Harmonic Elimination for Variable Frequency Traction Motor Drives Using Harris Hawks Optimization
In this paper, harris hawks optimization (HHO) for selective harmonic elimination method (SHEM) of a voltage source inverter has been applied to a traction motor drive for light rail transportation. The main objective of SHEM's pulse-width modulation strategy is to remove the low-order harmonics by solving nonlinear equations while satisfying the required fundamental component's magnitude. The HHO applied in this paper to a two-level, three-phase inverter aims at solving the associated nonlinear equations with a high accuracy and convergence probability as a strong metaheuristic algorithm. SHEM simulations are carried out via MATLAB / Simulink on a 125 kW traction motor drive platform for various SHEM angles to verify its performance in comparison with the SHEM with SPWM and SVM techniques. Experimental results obtained on a physical simulator of the light rail transportation system in the laboratory have shown remarkable findings in view of the DC link voltage magnitude on the performance of the associated traction motor drive. In the light of different fundamental frequency operations, the number of SHEM angles, and operating DC link voltages, a general evaluation of the SHEM has been made in considering its application to a light rail traction motor drive. It has also been shown that the application of online SHEM on a GPU framework is possible in real-time.
- Open Access
- 29 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (9) , 1438
All-SiC Traction Converter for Light Rail Transportation Systems: Design Methodology and Development of 165 kVA Prototype
The design and development of a high-performance 165 kVA, 750 V DC all-silicon carbide (SiC) traction converter for new generation light rail transportation systems (LRTSs) are described. In the design of the traction motor drive, the efficiency of the overall system is maximized and the line current harmonic content of the traction motor is minimized. A complete mathematical model of the physical system is derived to carry out real-time simulations and proper control of the LRTS on a real rail track. The electrical and thermal performances of traction-type SiC power MOSFET modules are compared with those of alternative hybrid and Si-IGBT modules for various switching frequencies. The implementation of the developed system is also described. The performance of the resulting system is verified experimentally on a full-scale physical simulator as well as for various track conditions. Very promising results for the next generation railway traction motor drives have been obtained in terms of performance criteria, such as very high efficiency, low harmonic distortion of the motor line current, low cooling requirement, relatively high switching frequency, and hence, superior controller performance. The effects of the SiC power MOSFET operation on the insulation of the available traction motors are also examined experimentally. This paper is accompanied by a video demonstrating the experimental work.
- 29 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (9) , 1438
Open AccessAll-SiC Traction Converter for Light Rail Transportation Systems: Design Methodology and Development of 165 kVA Prototype
The design and development of a high-performance 165 kVA, 750 V DC all-silicon carbide (SiC) traction converter for new generation light rail transportation systems (LRTSs) are described. In the design of the traction motor drive, the efficiency of the overall system is maximized and the line current harmonic content of the traction motor is minimized. A complete mathematical model of the physical system is derived to carry out real-time simulations and proper control of the LRTS on a real rail track. The electrical and thermal performances of traction-type SiC power MOSFET modules are compared with those of alternative hybrid and Si-IGBT modules for various switching frequencies. The implementation of the developed system is also described. The performance of the resulting system is verified experimentally on a full-scale physical simulator as well as for various track conditions. Very promising results for the next generation railway traction motor drives have been obtained in terms of performance criteria, such as very high efficiency, low harmonic distortion of the motor line current, low cooling requirement, relatively high switching frequency, and hence, superior controller performance. The effects of the SiC power MOSFET operation on the insulation of the available traction motors are also examined experimentally. This paper is accompanied by a video demonstrating the experimental work.
- Open Access
- 1 February 2020
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 13 (3) , 483-494
All SiC PWM rectifier‐based off‐board ultrafast charger for heavy electric vehicles
This study deals with the design, implementation and experimental performance of all silicon carbide pulse width modulation (SiC PWM) rectifier‐based off‐board ultrafast chargers (UFCs) for lithium titanate batteries of heavy electric vehicles. Different UFC configurations are proposed, depending upon the nominal battery voltage (400–1000 V DC) and charge capacity. Operating principles and control of UFC at unity and leading power factors are assessed and corresponding operating modes of PWM rectifier are discussed. The combined effect of reverse conduction characteristic of SiC power metal oxide semiconductor field effect transistor (MOSFET) and built‐in SiC Schottky diode is taken into account in all the analyses carried out. The operating performance of the developed UFC, such as the switching characteristics of SiC power MOSFET modules, efficiency, input current total demand distortion (ITDD), and thermal limitations of the SiC PWM rectifier have been assessed for various charge voltages and charge capacities, both by computer simulations and laboratory tests. Power circuit layout considerations of the proposed system are also given in this study. Excellent performance results for 10 kHz switching frequency are obtained from the developed 200 kW UFC, with operating efficiencies higher than 98.5% for all charging rates up to five times the battery capacity, and ITDDs <2.2% for the whole operating range.
- 1 February 2020
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 13 (3) , 483-494
Open AccessAll SiC PWM rectifier‐based off‐board ultrafast charger for heavy electric vehicles
This study deals with the design, implementation and experimental performance of all silicon carbide pulse width modulation (SiC PWM) rectifier‐based off‐board ultrafast chargers (UFCs) for lithium titanate batteries of heavy electric vehicles. Different UFC configurations are proposed, depending upon the nominal battery voltage (400–1000 V DC) and charge capacity. Operating principles and control of UFC at unity and leading power factors are assessed and corresponding operating modes of PWM rectifier are discussed. The combined effect of reverse conduction characteristic of SiC power metal oxide semiconductor field effect transistor (MOSFET) and built‐in SiC Schottky diode is taken into account in all the analyses carried out. The operating performance of the developed UFC, such as the switching characteristics of SiC power MOSFET modules, efficiency, input current total demand distortion (ITDD), and thermal limitations of the SiC PWM rectifier have been assessed for various charge voltages and charge capacities, both by computer simulations and laboratory tests. Power circuit layout considerations of the proposed system are also given in this study. Excellent performance results for 10 kHz switching frequency are obtained from the developed 200 kW UFC, with operating efficiencies higher than 98.5% for all charging rates up to five times the battery capacity, and ITDDs <2.2% for the whole operating range.
- 10 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 67 (8) , 6290-6301
Full-Scale Physical Simulator of All SiC Traction Motor Drive With Onboard Supercapacitor ESS for Light-Rail Public Transportation
This paper deals with the design, and laboratory implementation of a full scale, physical simulator of an all silicon carbide (SiC) traction motor drive for Light-Rail Transit Systems (LRTS) with on-board super-capacitor energy storage system (ESS). It consists of a PWM rectifier representing the 750 V DC catenary line, a three-phase two-level PWM traction inverter to drive a three-phase squirrel-cage traction motor, a flywheel coupled to the motor shaft to represent the dynamic behaviour of the transportation vehicle, a loading generator connected to the grid via DC link converter with active front-end, and a supercapacitor ESS containing a bidirectional DC/DC converter supplied from the common DC link. PWM rectifier, traction inverter and bidirectional DC/DC converter are all SiC power MOSFET based converters for high efficiency and high power density. The physical simulator is a valuable tool in the design and testing of all SiC converters. It is equipped with software programs for catenary model, rail-track model and vehicle model, and permits the performance verification of various control, modulation, and energy saving strategies. The physical simulator system developed in this research work allows the performance verification of a vehicle formation on a pre-specified real track and evaluation of benefits of the on-board supercapacitor ESS in real-time.
- 10 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 67 (8) , 6290-6301
Full-Scale Physical Simulator of All SiC Traction Motor Drive With Onboard Supercapacitor ESS for Light-Rail Public Transportation
This paper deals with the design, and laboratory implementation of a full scale, physical simulator of an all silicon carbide (SiC) traction motor drive for Light-Rail Transit Systems (LRTS) with on-board super-capacitor energy storage system (ESS). It consists of a PWM rectifier representing the 750 V DC catenary line, a three-phase two-level PWM traction inverter to drive a three-phase squirrel-cage traction motor, a flywheel coupled to the motor shaft to represent the dynamic behaviour of the transportation vehicle, a loading generator connected to the grid via DC link converter with active front-end, and a supercapacitor ESS containing a bidirectional DC/DC converter supplied from the common DC link. PWM rectifier, traction inverter and bidirectional DC/DC converter are all SiC power MOSFET based converters for high efficiency and high power density. The physical simulator is a valuable tool in the design and testing of all SiC converters. It is equipped with software programs for catenary model, rail-track model and vehicle model, and permits the performance verification of various control, modulation, and energy saving strategies. The physical simulator system developed in this research work allows the performance verification of a vehicle formation on a pre-specified real track and evaluation of benefits of the on-board supercapacitor ESS in real-time.
- 15 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 6613-6623
Real-Time Detection of Interharmonics and Harmonics of AC Electric Arc Furnaces on GPU Framework
In this paper, a method based on the multiple synchronous reference frame (MSRF) analysis is recommended and implemented to detect time-varying harmonics and interharmonics of rapidly fluctuating asymmetrical industrial loads. The experimental work has been carried out on a typical three-phase alternating current arc furnace (AC EAF) installation. In the recommended method, the reference frame is rotated in both directions at speeds corresponding to the positive and negative sequences of all harmonics and all interharmonics 5-Hz apart. To extract the direct current (DC) components of the transformed d-q quantities, a low-pass filter is employed. In order to keep the delay of the filter at zero frequency less than a few ms, Kalman estimation technique has been used. Back transformation is then applied for each harmonic and interharmonic component to obtain their positive- and negative- sequences of the associated harmonic and interharmonic in the actual line current waveforms. Parallel computing technique has been applied for the real-time detection of both the phase and the amplitude of all harmonics and interharmonics. This is achieved on NVDIA Jetson TX1 graphics processing unit (GPU) framework for a sample industrial plant. The developed system is shown to be useful for fast and accurate generation of reference signals for the controllers of the advanced technology power conditioning systems which successfully compensates interharmonics, harmonics, and flicker of the rapidly fluctuating nonlinear industrial loads.
- 15 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 6613-6623
Real-Time Detection of Interharmonics and Harmonics of AC Electric Arc Furnaces on GPU Framework
In this paper, a method based on the multiple synchronous reference frame (MSRF) analysis is recommended and implemented to detect time-varying harmonics and interharmonics of rapidly fluctuating asymmetrical industrial loads. The experimental work has been carried out on a typical three-phase alternating current arc furnace (AC EAF) installation. In the recommended method, the reference frame is rotated in both directions at speeds corresponding to the positive and negative sequences of all harmonics and all interharmonics 5-Hz apart. To extract the direct current (DC) components of the transformed d-q quantities, a low-pass filter is employed. In order to keep the delay of the filter at zero frequency less than a few ms, Kalman estimation technique has been used. Back transformation is then applied for each harmonic and interharmonic component to obtain their positive- and negative- sequences of the associated harmonic and interharmonic in the actual line current waveforms. Parallel computing technique has been applied for the real-time detection of both the phase and the amplitude of all harmonics and interharmonics. This is achieved on NVDIA Jetson TX1 graphics processing unit (GPU) framework for a sample industrial plant. The developed system is shown to be useful for fast and accurate generation of reference signals for the controllers of the advanced technology power conditioning systems which successfully compensates interharmonics, harmonics, and flicker of the rapidly fluctuating nonlinear industrial loads.
- Open Access
- 20 August 2018
- Published by MDPI AG in Electronics
- Vol. 7 (8) , 151
On-Line Application of SHEM by Particle Swarm Optimization to Grid-Connected, Three-Phase, Two-Level VSCs with Variable DC Link Voltage
This paper is devoted to an otablen-line application of the selective harmonic elimination method (SHEM) to three-phase, two-level, grid-connected voltage source converters (VSCs) by particle swarm optimization (PSO). In such systems, active power can be controlled by the phase shift angle, and reactive power by the modulation index, against variations in the direct current (DC) link voltage. Some selected, low-odd-order harmonic components in the line-to-neutral output voltage waveforms are eliminated by calculating the SHEM angle set continuously through the developed PSO algorithm on field-programmable gate array (FPGA)-based computing hardware as the modulation index is varied. The use of powerful computing hardware permits the elimination of all harmonics up to 50th. The cost function of the developed PSO algorithm is formulated by using an optimum number of particles to obtain a global optimum solution with a small fitness value in each half-cycle of the grid voltage and then updating the SHEM angle set at the beginning of the next full-cycle. Since the convergence of the solution to a global minimum point depends upon the use of correct initial values especially for a large number of SHEM angles, a generalized initialization procedure is also described in the paper. Theoretical results are verified initially using hardware co-simulation. They are also tested using a small scale photovoltaic (PV) supply prototype developed specifically for this purpose. It is demonstrated that the 5th, 7th, 11th, 13th, 17th, and 19th sidekick harmonics are eliminated by on-line calculation of seven SHEM angles through the developed PSO algorithm on a moderately powerful XEM6010-LX150, USB-2.0-integrated FPGA module. All control and protection actions and the calculation of SHEM angles are achieved by a single FPGA chip and its peripherals within the FPGA board.
- 20 August 2018
- Published by MDPI AG in Electronics
- Vol. 7 (8) , 151
Open AccessOn-Line Application of SHEM by Particle Swarm Optimization to Grid-Connected, Three-Phase, Two-Level VSCs with Variable DC Link Voltage
This paper is devoted to an otablen-line application of the selective harmonic elimination method (SHEM) to three-phase, two-level, grid-connected voltage source converters (VSCs) by particle swarm optimization (PSO). In such systems, active power can be controlled by the phase shift angle, and reactive power by the modulation index, against variations in the direct current (DC) link voltage. Some selected, low-odd-order harmonic components in the line-to-neutral output voltage waveforms are eliminated by calculating the SHEM angle set continuously through the developed PSO algorithm on field-programmable gate array (FPGA)-based computing hardware as the modulation index is varied. The use of powerful computing hardware permits the elimination of all harmonics up to 50th. The cost function of the developed PSO algorithm is formulated by using an optimum number of particles to obtain a global optimum solution with a small fitness value in each half-cycle of the grid voltage and then updating the SHEM angle set at the beginning of the next full-cycle. Since the convergence of the solution to a global minimum point depends upon the use of correct initial values especially for a large number of SHEM angles, a generalized initialization procedure is also described in the paper. Theoretical results are verified initially using hardware co-simulation. They are also tested using a small scale photovoltaic (PV) supply prototype developed specifically for this purpose. It is demonstrated that the 5th, 7th, 11th, 13th, 17th, and 19th sidekick harmonics are eliminated by on-line calculation of seven SHEM angles through the developed PSO algorithm on a moderately powerful XEM6010-LX150, USB-2.0-integrated FPGA module. All control and protection actions and the calculation of SHEM angles are achieved by a single FPGA chip and its peripherals within the FPGA board.
- Open Access
- 31 May 2018
- Published by MDPI AG in Electronics
- Vol. 7 (6) , 85
All SiC Grid-Connected PV Supply with HF Link MPPT Converter: System Design Methodology and Development of a 20 kHz, 25 kVA Prototype
Design methodology and implementation of an all SiC power semiconductor-based, grid-connected multi-string photovoltaic (PV) supply with an isolated high frequency (HF) link maximum power point tracker (MPPT) have been described. This system configuration makes possible the use of a simple and reliable two-level voltage source inverter (VSI) topology for grid connection, owing to the galvanic isolation provided by the HF transformer. This topology provides a viable alternative to the commonly used non-isolated PV supplies equipped with Si-based boost MPPT converters cascaded with relatively more complex inverter topologies, at competitive efficiency figures and a higher power density. A 20 kHz, 25 kVA prototype system was designed based on the dynamic model of the multi-string PV panels obtained from field tests. Design parameters such as input DC link capacitance, switching frequencies of MPPT converter and voltage source inverter, size and performance of HF transformer with nanocrystalline core, DC link voltage, and LCL filter of the VSI were optimized in view of the site dependent parameters such as the variation ranges of solar insolation, module surface temperature, and grid voltage. A modified synchronous reference frame control was implemented in the VSI by applying the grid voltage feedforward to the reference voltages in abc axes directly, so that zero-sequence components of grid voltages are taken into account in the case of an unbalanced grid. The system was implemented and the proposed design methodology verified satisfactorily in the field on a roof-mounted 23.7 kW multi-string PV system.
- 31 May 2018
- Published by MDPI AG in Electronics
- Vol. 7 (6) , 85
Open AccessAll SiC Grid-Connected PV Supply with HF Link MPPT Converter: System Design Methodology and Development of a 20 kHz, 25 kVA Prototype
Design methodology and implementation of an all SiC power semiconductor-based, grid-connected multi-string photovoltaic (PV) supply with an isolated high frequency (HF) link maximum power point tracker (MPPT) have been described. This system configuration makes possible the use of a simple and reliable two-level voltage source inverter (VSI) topology for grid connection, owing to the galvanic isolation provided by the HF transformer. This topology provides a viable alternative to the commonly used non-isolated PV supplies equipped with Si-based boost MPPT converters cascaded with relatively more complex inverter topologies, at competitive efficiency figures and a higher power density. A 20 kHz, 25 kVA prototype system was designed based on the dynamic model of the multi-string PV panels obtained from field tests. Design parameters such as input DC link capacitance, switching frequencies of MPPT converter and voltage source inverter, size and performance of HF transformer with nanocrystalline core, DC link voltage, and LCL filter of the VSI were optimized in view of the site dependent parameters such as the variation ranges of solar insolation, module surface temperature, and grid voltage. A modified synchronous reference frame control was implemented in the VSI by applying the grid voltage feedforward to the reference voltages in abc axes directly, so that zero-sequence components of grid voltages are taken into account in the case of an unbalanced grid. The system was implemented and the proposed design methodology verified satisfactorily in the field on a roof-mounted 23.7 kW multi-string PV system.
- Open Access
- 20 April 2018
- Published by MDPI AG in Electronics
- Vol. 7 (4) , 53
Suppression of the Second Harmonic Subgroup Injected by an AC EAF: Design Considerations and Performance Estimation of a Shunt APF
This paper proposes a design methodology for an active power filter (APF) system to suppress the second harmonic subgroup injected by an AC electric arc furnace (EAF) to the utility grid. The APF system is composed of identical parallel units connected to the utility grid via a specially-designed coupling transformer. Each APF converter is a three-phase three-wire two-level voltage source converter (VSC). The number of parallel APF units, coupling transformer MVA rating, and turns ratio are optimized in the view of the ratings of commercially-available high voltage (HV) IGBTs. In this research work, line current waveforms sampled at 25.6-kS/s on the medium voltage (MV) side of a 65-MVA EAF transformer are then used to extract the second harmonic subgroup, 95-, 100-, and 105-Hz current components, by multiple synchronous reference frame (MSRF) analysis, which was previously proposed to decompose EAF current interharmonics and harmonics in real-time. By summing up this digital data of the second harmonic subgroup, the reference current signal for the APF system is produced in real-time. A detailed model of the APF system is then run on EMTDC/PSCAD to follow the produced reference current signal according to hysteresis band control philosophy. The simulation results show that the proposed APF system can successfully suppress the second harmonic subgroup of an AC EAF.
- 20 April 2018
- Published by MDPI AG in Electronics
- Vol. 7 (4) , 53
Open AccessSuppression of the Second Harmonic Subgroup Injected by an AC EAF: Design Considerations and Performance Estimation of a Shunt APF
This paper proposes a design methodology for an active power filter (APF) system to suppress the second harmonic subgroup injected by an AC electric arc furnace (EAF) to the utility grid. The APF system is composed of identical parallel units connected to the utility grid via a specially-designed coupling transformer. Each APF converter is a three-phase three-wire two-level voltage source converter (VSC). The number of parallel APF units, coupling transformer MVA rating, and turns ratio are optimized in the view of the ratings of commercially-available high voltage (HV) IGBTs. In this research work, line current waveforms sampled at 25.6-kS/s on the medium voltage (MV) side of a 65-MVA EAF transformer are then used to extract the second harmonic subgroup, 95-, 100-, and 105-Hz current components, by multiple synchronous reference frame (MSRF) analysis, which was previously proposed to decompose EAF current interharmonics and harmonics in real-time. By summing up this digital data of the second harmonic subgroup, the reference current signal for the APF system is produced in real-time. A detailed model of the APF system is then run on EMTDC/PSCAD to follow the produced reference current signal according to hysteresis band control philosophy. The simulation results show that the proposed APF system can successfully suppress the second harmonic subgroup of an AC EAF.
- 3 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 52 (3) , 2673-2683
Online Characterization of Interharmonics and Harmonics of AC Electric Arc Furnaces by Multiple Synchronous Reference Frame Analysis
In this paper, a multiple synchronous reference frame (MSRF) analysis framework is developed to determine the positive- and negative-sequence components of all interharmonic and harmonic currents produced by alternating current electric arc furnace (AC EAF) installations, which can be considered as balanced but asymmetrical three-phase, three-wire loads on the power system. The aim of developing the MSRF analysis framework is twofold; deep understanding of the EAF characteristics, and fast and accurate generation of reference signals to the controllers of the advanced technology compensation systems such as active power filters (APFs), synchronous static compensators (STATCOMs), and energy storage systems (ESS), which may successfully compensate interharmonics, harmonics, and flicker. Online characterization of interharmonics and harmonics by MSRF analysis utilizes continuously measured line currents and line voltages on the medium-voltage side of the EAF transformer at a sampling rate of 25.6-kHz per data channel. It has been shown by offline computations that compensation of the sequence components of interharmonics and harmonics of the EAF currents obtained by the proposed framework, reduces the short-term flicker values at the point of common coupling by up to 10-fold. The proposed MSRF analysis framework has been successfully verified by comparing the frequency spectrums of the EAF currents with Fourier analysis results based on one-cycle sliding windows of 10-cycle duration.
- 3 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 52 (3) , 2673-2683
Online Characterization of Interharmonics and Harmonics of AC Electric Arc Furnaces by Multiple Synchronous Reference Frame Analysis
In this paper, a multiple synchronous reference frame (MSRF) analysis framework is developed to determine the positive- and negative-sequence components of all interharmonic and harmonic currents produced by alternating current electric arc furnace (AC EAF) installations, which can be considered as balanced but asymmetrical three-phase, three-wire loads on the power system. The aim of developing the MSRF analysis framework is twofold; deep understanding of the EAF characteristics, and fast and accurate generation of reference signals to the controllers of the advanced technology compensation systems such as active power filters (APFs), synchronous static compensators (STATCOMs), and energy storage systems (ESS), which may successfully compensate interharmonics, harmonics, and flicker. Online characterization of interharmonics and harmonics by MSRF analysis utilizes continuously measured line currents and line voltages on the medium-voltage side of the EAF transformer at a sampling rate of 25.6-kHz per data channel. It has been shown by offline computations that compensation of the sequence components of interharmonics and harmonics of the EAF currents obtained by the proposed framework, reduces the short-term flicker values at the point of common coupling by up to 10-fold. The proposed MSRF analysis framework has been successfully verified by comparing the frequency spectrums of the EAF currents with Fourier analysis results based on one-cycle sliding windows of 10-cycle duration.