Irina Sknar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Irina Sknar has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Anna Cheremysinova
Ukrainian State University of Chemical Technology Gagarina ave., 8, Dnipro, Ukraine, 49005
3 shared publications Oleksii Sigunov
Ukrainian State University of Chemical Technology Gagarina ave., 8, Dnipro, Ukraine, 49005
2 shared publicationsYaroslav Kozlov
Ukrainian State University of Chemical Technology Gagarina ave., 8, Dnipro, Ukraine, 49005
2 shared publications- Ann Karakurkchi
National Technical University “Kharkiv Polytechnic Institute
1 shared publication - Elena Vlasova
SHEI «National Metallurgical Academy of Ukraine» Gagarina ave., 8, Dnipro, Ukraine, 49600
1 shared publication F. I. Danylov
“Ukrainian State University of Chemical Technology” State Higher Institution
1 shared publication
Latest Publications
- Open Access
- 19 June 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (12 (87)) , 9-15
Research into influence of the electrolysis modes on the composition of galvanic Fe-Co-Mo coatings
We examined the influence of the energy (current density і) and temporal (duration of pulse ton and pause toff, the ratio of ton/toff) parameters of the electrolysis on the composition and morphology of the Fe-Co-Mo coatings. An increase in the pulse duration contributes to the enrichment of alloy with molybdenum in proportion to the increasing current density. At the ratio of pulse/pause ton/toff>1–2, the composition of an alloy changes towards an increase in the content of iron. We demonstrated a tendency of the enrichment of coatings with a high-melting component and a decrease in the content of iron with an increase in the current density. It is shown that with an increase in the current density, the surface of coatings changes from the fine-grained to the globular structure. It was established that at fixed ton/toff, the power yield grows with an increase in the pulse duration over the entire interval of current densities. With an increase in the current density (at ton/toff=const) we observe a reduction in the process efficiency. It was found that the most optimal for obtaining the soft magnetic Fe-Co-Mo coatings is the current amplitude of 3 A/dm2, the duration of pulse 2–5 ms and of pause 10–20 ms. Current at amplitude of 5 A/dm2 is recommended when obtaining materials with the content of a high-melting component larger than 15 аt. %. It is shown that the regime of the unipolar pulse current makes it possible to obtain the Fe-Co-Mo coatings with the content of iron of 58–46 аt. %, cobalt – 34–43 аt. % and molybdenum – 6–17 аt. %. The results obtained create prerequisites to control the composition and properties of the Fe-Co-Mo coatings with a wide range of content of the alloy-forming components.
- 19 June 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (12 (87)) , 9-15
Open AccessResearch into influence of the electrolysis modes on the composition of galvanic Fe-Co-Mo coatings
We examined the influence of the energy (current density і) and temporal (duration of pulse ton and pause toff, the ratio of ton/toff) parameters of the electrolysis on the composition and morphology of the Fe-Co-Mo coatings. An increase in the pulse duration contributes to the enrichment of alloy with molybdenum in proportion to the increasing current density. At the ratio of pulse/pause ton/toff>1–2, the composition of an alloy changes towards an increase in the content of iron. We demonstrated a tendency of the enrichment of coatings with a high-melting component and a decrease in the content of iron with an increase in the current density. It is shown that with an increase in the current density, the surface of coatings changes from the fine-grained to the globular structure. It was established that at fixed ton/toff, the power yield grows with an increase in the pulse duration over the entire interval of current densities. With an increase in the current density (at ton/toff=const) we observe a reduction in the process efficiency. It was found that the most optimal for obtaining the soft magnetic Fe-Co-Mo coatings is the current amplitude of 3 A/dm2, the duration of pulse 2–5 ms and of pause 10–20 ms. Current at amplitude of 5 A/dm2 is recommended when obtaining materials with the content of a high-melting component larger than 15 аt. %. It is shown that the regime of the unipolar pulse current makes it possible to obtain the Fe-Co-Mo coatings with the content of iron of 58–46 аt. %, cobalt – 34–43 аt. % and molybdenum – 6–17 аt. %. The results obtained create prerequisites to control the composition and properties of the Fe-Co-Mo coatings with a wide range of content of the alloy-forming components.
- Open Access
- 8 June 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (6 (87)) , 60-66
Study of thermal dehydration of sodium orthophosphate monosubstituted
Depending on the conditions of conducting the synthesis, it is possible to obtain polymeric phosphates of different composition and structure. The mixtures of polyphosphates, employed in the production of technological lubricants, are expedient to synthesize by the high-temperature dehydration of sodium orthophosphate monosubstituted. The temperature ranges, over which the thermochemical transformations of sodium orthophosphate monosubstituted with the formation of polyphosphates proceed, are established by the thermogravimetric method. The composition of polyphosphates is determined using the X-ray phase analysis. Quantitative composition of the mixtures of polyphosphates is determined by applying the original method of eluent ion-exchange chromatography. It is established that the basic products of thermal dehydration of sodium orthophosphate monosubstituted in the range of temperatures 200–650 °C are Na3Р3О9, Na2H2P2O7 and Na6P6O18. Thermochemical transformations of NaH2PO4 into Na6P6O18 at temperature 650 °C are accompanied by the side reactions of formation of Na3H2P3O10. We proposed the chemical scheme of the high-temperature dehydration of sodium orthophosphate monosubstituted. Kinetics of the isothermal process of obtaining the polymeric phosphates from sodium orthophosphate monosubstituted at different temperatures is examined.We established quantitative composition of the mixtures of inorganic polymeric phosphates depending on the duration of isothermal process of dehydration. The possibility of obtaining a salt mixture of polymeric phosphates of the assigned qualitative and quantitative composition is demonstrated. We proposed to use the mixture: 76 % Na6P6O18, 8 % Na2H2P2O7, 8 % Na3H2P3O10, 8 % NaH2PO4, obtained at 650 °C, as the basic phosphate component of technological lubricants for the hot rolling of pipes.
- 8 June 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (6 (87)) , 60-66
Open AccessStudy of thermal dehydration of sodium orthophosphate monosubstituted
Depending on the conditions of conducting the synthesis, it is possible to obtain polymeric phosphates of different composition and structure. The mixtures of polyphosphates, employed in the production of technological lubricants, are expedient to synthesize by the high-temperature dehydration of sodium orthophosphate monosubstituted. The temperature ranges, over which the thermochemical transformations of sodium orthophosphate monosubstituted with the formation of polyphosphates proceed, are established by the thermogravimetric method. The composition of polyphosphates is determined using the X-ray phase analysis. Quantitative composition of the mixtures of polyphosphates is determined by applying the original method of eluent ion-exchange chromatography. It is established that the basic products of thermal dehydration of sodium orthophosphate monosubstituted in the range of temperatures 200–650 °C are Na3Р3О9, Na2H2P2O7 and Na6P6O18. Thermochemical transformations of NaH2PO4 into Na6P6O18 at temperature 650 °C are accompanied by the side reactions of formation of Na3H2P3O10. We proposed the chemical scheme of the high-temperature dehydration of sodium orthophosphate monosubstituted. Kinetics of the isothermal process of obtaining the polymeric phosphates from sodium orthophosphate monosubstituted at different temperatures is examined.We established quantitative composition of the mixtures of inorganic polymeric phosphates depending on the duration of isothermal process of dehydration. The possibility of obtaining a salt mixture of polymeric phosphates of the assigned qualitative and quantitative composition is demonstrated. We proposed to use the mixture: 76 % Na6P6O18, 8 % Na2H2P2O7, 8 % Na3H2P3O10, 8 % NaH2PO4, obtained at 650 °C, as the basic phosphate component of technological lubricants for the hot rolling of pipes.
- Open Access
- 26 April 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (11 (86)) , 43-49
Investigation of adsorption behavior of smoothing additives in copper plating electrolytes
Smoothing additives are the necessary component of copper plating electrolytes. Choice of the required additive is determined by the type of electrolyte and its pH values. Studies of adsorption behavior of such compounds in electrolytes with different acidities are of current interest. Adsorption activity of poly-N, N'-dimethylsafranine and poly-N, N'-diethylsafranine on the copper electrode in sulfate electrolytes was established in the present work. The dependencies of the differential capacitance of the double electric layer of the copper electrode on the potential which were obtained in acidic (pH 1.7) and neutral (pH 5.9) electrolytes indicate that acidity of the medium has a significant effect on the additive adsorption. The studied organic substances show high adsorption activity in an acidic solution. The likely cause of the established phenomenon in an acid medium is transition of these organic compounds to a protonated state with formation of positively charged amino groups. Cationic groups of the additives are responsible for an additional interaction with the cathode surface and provide stronger adsorption of poly-N, N'-dimethylsafranine and poly N, N'-diethylsafranine on the copper electrode in comparison with a neutral sulfate electrolyte. Poly-N, N'-diethylsafranine with its molecular weight higher than that of poly-N, N'-dimethylsafranine is characterized by higher adsorbability. Since the smoothing effect of additives in electrodeposition of copper coatings is determined by their adsorption properties, it should be expected that the most effective in this process will be the use of poly-N, N'-diethylsafranine at lower pH values of the copper plating electrolytes.
- 26 April 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (11 (86)) , 43-49
Open AccessInvestigation of adsorption behavior of smoothing additives in copper plating electrolytes
Smoothing additives are the necessary component of copper plating electrolytes. Choice of the required additive is determined by the type of electrolyte and its pH values. Studies of adsorption behavior of such compounds in electrolytes with different acidities are of current interest. Adsorption activity of poly-N, N'-dimethylsafranine and poly-N, N'-diethylsafranine on the copper electrode in sulfate electrolytes was established in the present work. The dependencies of the differential capacitance of the double electric layer of the copper electrode on the potential which were obtained in acidic (pH 1.7) and neutral (pH 5.9) electrolytes indicate that acidity of the medium has a significant effect on the additive adsorption. The studied organic substances show high adsorption activity in an acidic solution. The likely cause of the established phenomenon in an acid medium is transition of these organic compounds to a protonated state with formation of positively charged amino groups. Cationic groups of the additives are responsible for an additional interaction with the cathode surface and provide stronger adsorption of poly-N, N'-dimethylsafranine and poly N, N'-diethylsafranine on the copper electrode in comparison with a neutral sulfate electrolyte. Poly-N, N'-diethylsafranine with its molecular weight higher than that of poly-N, N'-dimethylsafranine is characterized by higher adsorbability. Since the smoothing effect of additives in electrodeposition of copper coatings is determined by their adsorption properties, it should be expected that the most effective in this process will be the use of poly-N, N'-diethylsafranine at lower pH values of the copper plating electrolytes.
- Open Access
- 25 April 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (86)) , 4-10
Investigation of composition and structure of tripoliphosphate coating on low carbon steel
The hypothesis on the matrix (composite) structure of the iron (III) tripolyphosphate precipitate and polyphosphate coatings on the steel substrate has been justified experimentally. According to the hypothesis, that iron (III) tripolyphosphate acts as a matrix forming agent while water-soluble sodium tripolyphosphate corrosion inhibitor is a filler. Be means of the chemical synthesis method, it has been demonstrated that the chemical basis of the coating formed on the steel surface in the STPP solution is iron (III) tripolyphosphate. It has been established that the composite structure of tripolyphosphate coatings and precipitates is determined by the nature of iron (III) tripolyphosphate. The conducted investigation on the composition of the iron (III) tripolyphosphate precipitate and tripolyphosphate coating on steel, using the gravimetric method with washing have proved the presence of STPP. The results of X-ray spectral analysis have revealed that STPP in the structure of composite coating is situated not only as a filler inside the matrix but also as an additional layer on its surface. The chemical protection mechanism of the tripolyphosphate coating on steel in atmospheric conditions has been justified.The acquired knowledge would expand the theoretical and practical concept of the structure and properties of tripolyphosphate coatings on the steel substrate and their protection mechanism in conditions of atmospheric corrosion. The application of new knowledge in researches aimed at the development of ecologically safe methods of tripolyphosphate coating deposition with estimated complex of properties, would increase their efficiency.
- 25 April 2017
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (86)) , 4-10
Open AccessInvestigation of composition and structure of tripoliphosphate coating on low carbon steel
The hypothesis on the matrix (composite) structure of the iron (III) tripolyphosphate precipitate and polyphosphate coatings on the steel substrate has been justified experimentally. According to the hypothesis, that iron (III) tripolyphosphate acts as a matrix forming agent while water-soluble sodium tripolyphosphate corrosion inhibitor is a filler. Be means of the chemical synthesis method, it has been demonstrated that the chemical basis of the coating formed on the steel surface in the STPP solution is iron (III) tripolyphosphate. It has been established that the composite structure of tripolyphosphate coatings and precipitates is determined by the nature of iron (III) tripolyphosphate. The conducted investigation on the composition of the iron (III) tripolyphosphate precipitate and tripolyphosphate coating on steel, using the gravimetric method with washing have proved the presence of STPP. The results of X-ray spectral analysis have revealed that STPP in the structure of composite coating is situated not only as a filler inside the matrix but also as an additional layer on its surface. The chemical protection mechanism of the tripolyphosphate coating on steel in atmospheric conditions has been justified.The acquired knowledge would expand the theoretical and practical concept of the structure and properties of tripolyphosphate coatings on the steel substrate and their protection mechanism in conditions of atmospheric corrosion. The application of new knowledge in researches aimed at the development of ecologically safe methods of tripolyphosphate coating deposition with estimated complex of properties, would increase their efficiency.
- 1 November 2016
- Published by Springer Nature in Materials Science
- Vol. 52 (3) , 396-401
Influence of Methylsulfonate Anions on the Structure of Electrolytic Cobalt Coatings
- 1 November 2016
- Published by Springer Nature in Materials Science
- Vol. 52 (3) , 396-401
Influence of Methylsulfonate Anions on the Structure of Electrolytic Cobalt Coatings