Lin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lin Li has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Weisen Zheng
School of Materials Science and Engineering, Shanghai University, Shanghai, China
3 shared publications - Yanlin He
State Key Laboratory of Advanced Special Steel, School of Materials Science and Engineering, Shanghai University, Shanghai 200444, China
3 shared publications Yan-Lin He
Shanghai University
2 shared publications- Bo-Wei Sun
School of Material Science and Engineering, Shanghai University, Shanghai 200444, China
1 shared publication - Cansheng Yu
State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China
1 shared publication - Di Tang
Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing 100083, China
1 shared publication
Latest Publications
- Open Access
Microstructural Evolution and Mechanical Properties of V-Containing Medium-Mn Steel Adopting Simple Intercritical Annealing
The variations of the microstructure and mechanical properties of medium-Mn steel after vanadium (V) microalloying with different contents were investigated. After a one-step intercritical annealing (IA) at 730 °C, the steel containing 0.04 wt.% of V exhibited excellent comprehensive properties. The steel maintained an ultimate tensile strength (UTS) of 1000 MPa while also exhibiting a total elongation (TEL) of 37% and a product of strength and plasticity (PSE) of 37.7 GPa%. V-microalloying improved the yield strength (YS) and UTS of the experimental steel by refining ferrite grains and precipitation strengthening, however, it deteriorated its plasticity, which is difficult to compensate for through grain refinement and due to the TRIP effect of retained austenite (RA). The largest amount of RA and the appropriate stability also make a significant contribution to the outstanding UTS of the steel containing 0.04 wt.% of V through the TRIP effect. However, the further increase of V content led to decreased RA content and stability, weakening the TRIP effect and resulting in a weaker strength ductility balance.
Open AccessMicrostructural Evolution and Mechanical Properties of V-Containing Medium-Mn Steel Adopting Simple Intercritical Annealing
The variations of the microstructure and mechanical properties of medium-Mn steel after vanadium (V) microalloying with different contents were investigated. After a one-step intercritical annealing (IA) at 730 °C, the steel containing 0.04 wt.% of V exhibited excellent comprehensive properties. The steel maintained an ultimate tensile strength (UTS) of 1000 MPa while also exhibiting a total elongation (TEL) of 37% and a product of strength and plasticity (PSE) of 37.7 GPa%. V-microalloying improved the yield strength (YS) and UTS of the experimental steel by refining ferrite grains and precipitation strengthening, however, it deteriorated its plasticity, which is difficult to compensate for through grain refinement and due to the TRIP effect of retained austenite (RA). The largest amount of RA and the appropriate stability also make a significant contribution to the outstanding UTS of the steel containing 0.04 wt.% of V through the TRIP effect. However, the further increase of V content led to decreased RA content and stability, weakening the TRIP effect and resulting in a weaker strength ductility balance.
- Open Access
Effect of V Addition on Microstructure and Mechanical Properties in C–Mn–Si Steels after Quenching and Partitioning Processes
Three C-Si-Mn Q&P steels with different V addition after one-step and two-step quenching and partitioning (Q&P) processes were investigated by means of optical microstructure observation, X-ray diffraction (XRD) measurement, transmission electron microscopy (TEM) characterization and particle size distribution (PSD) analysis. The effect of V addition on strength and ductility of the steels was elucidated by comparative analysis on the microstructure and mechanical properties as functions of partitioning time and temperature. For one-step Q&P treatment, the mechanical properties were mainly controlled by the tempering behavior of martensite during partitioning. V addition was helpful to mitigate the deterioration of mechanical properties by precipitation strengthening and grain refinement strengthening. For two-step Q&P treatment, the satisfying plasticity was attributed to the transformation-induced plasticity (TRIP) effect of retained austenite maintaining the high work hardening rate at high strain regime. The higher volume fraction of retained austenite with high stability resulted from the refined microstructure and the promoted carbon partitioning for the steel with 0.16 wt% V addition. However, the carbon consumption due to the formation of VC carbides led to the strength reduction of tempered martensite.
Open AccessEffect of V Addition on Microstructure and Mechanical Properties in C–Mn–Si Steels after Quenching and Partitioning Processes
Three C-Si-Mn Q&P steels with different V addition after one-step and two-step quenching and partitioning (Q&P) processes were investigated by means of optical microstructure observation, X-ray diffraction (XRD) measurement, transmission electron microscopy (TEM) characterization and particle size distribution (PSD) analysis. The effect of V addition on strength and ductility of the steels was elucidated by comparative analysis on the microstructure and mechanical properties as functions of partitioning time and temperature. For one-step Q&P treatment, the mechanical properties were mainly controlled by the tempering behavior of martensite during partitioning. V addition was helpful to mitigate the deterioration of mechanical properties by precipitation strengthening and grain refinement strengthening. For two-step Q&P treatment, the satisfying plasticity was attributed to the transformation-induced plasticity (TRIP) effect of retained austenite maintaining the high work hardening rate at high strain regime. The higher volume fraction of retained austenite with high stability resulted from the refined microstructure and the promoted carbon partitioning for the steel with 0.16 wt% V addition. However, the carbon consumption due to the formation of VC carbides led to the strength reduction of tempered martensite.
- Open Access
Microstructures and Properties of Auto-Tempering Ultra-High Strength Automotive Steel under Different Thermal-Processing Conditions
Automotive steels with ultra-high strength and low alloy content under different heating and cooling processes were investigated. It was shown that those processes exhibited a great influence on the performance of the investigated steels due to the different auto-tempering effects. Compared with the steels under water quenching, there was approximately a 70% increase in the strength and elongation of steels under air cooling, in which the martensite was well-tempered. Although the elongation of the steel with a microstructure composed of ferrite, well-tempered martensite and less-tempered martensite could exceed 15%, the hole expansion ratio was still lower because of the undesirable hardness distribution between the hard phases and the soft phases. It followed from the calculation results based on SEM, TEM and XRD analyses, that for the steel under air cooling, the strengthening mechanism was dominated by the solid solution strengthening and the elongation was determined by the auto-tempering of martensite. Experiments and analyses aimed to explore the strengthening and plasticity mechanisms of auto-tempering steels under the special process of flash heating.
Open AccessMicrostructures and Properties of Auto-Tempering Ultra-High Strength Automotive Steel under Different Thermal-Processing Conditions
Automotive steels with ultra-high strength and low alloy content under different heating and cooling processes were investigated. It was shown that those processes exhibited a great influence on the performance of the investigated steels due to the different auto-tempering effects. Compared with the steels under water quenching, there was approximately a 70% increase in the strength and elongation of steels under air cooling, in which the martensite was well-tempered. Although the elongation of the steel with a microstructure composed of ferrite, well-tempered martensite and less-tempered martensite could exceed 15%, the hole expansion ratio was still lower because of the undesirable hardness distribution between the hard phases and the soft phases. It followed from the calculation results based on SEM, TEM and XRD analyses, that for the steel under air cooling, the strengthening mechanism was dominated by the solid solution strengthening and the elongation was determined by the auto-tempering of martensite. Experiments and analyses aimed to explore the strengthening and plasticity mechanisms of auto-tempering steels under the special process of flash heating.
- Open Access
Effect of Hot-Dip Galvanizing Process on Selective Oxidation and Galvanizability of Medium Manganese Steel for Automotive Application
A medium manganese steel with 7.5 wt.% Mn for automobile application was galvanized in a continuous Hot Dip Galvanizing (HDG) simulator under different galvanizing conditions. It was shown that the effects of dew point, annealing temperature and annealing atmosphere on the surface oxidation of steel could be comprehensively evaluated by the consideration of oxygen partial pressure P(O2). Although Mn2SiO4 was a thermodynamic stable phase when P(O2) varied from 10−28 to 10−21 atm, it was difficult to form Mn–Si–O composite oxide because there was no enrichment of silicon on the steel surface. So, this oxide was generally formed in the Fe substrate and had little effect on the galvanizability. With the increase in P(O2) above 10−25 atm, MnO particles in the form of the thermodynamic stable phase became coarser and tended to aggregate, which hindered the formation of a continuous inhibition layer, resulting in the defects of bare spots on the galvanized surface of the steel. When the oxygen partial pressure greater than 10−22 atm, film-like MnO layer was formed on the surface of steel sample, which obviously deteriorated the galvanizability. The galvanizability of the steel can be improved by the regulation of oxygen partial pressure; based on this, the reasonable zinc plating process parameters can be developed.
Open AccessEffect of Hot-Dip Galvanizing Process on Selective Oxidation and Galvanizability of Medium Manganese Steel for Automotive Application
A medium manganese steel with 7.5 wt.% Mn for automobile application was galvanized in a continuous Hot Dip Galvanizing (HDG) simulator under different galvanizing conditions. It was shown that the effects of dew point, annealing temperature and annealing atmosphere on the surface oxidation of steel could be comprehensively evaluated by the consideration of oxygen partial pressure P(O2). Although Mn2SiO4 was a thermodynamic stable phase when P(O2) varied from 10−28 to 10−21 atm, it was difficult to form Mn–Si–O composite oxide because there was no enrichment of silicon on the steel surface. So, this oxide was generally formed in the Fe substrate and had little effect on the galvanizability. With the increase in P(O2) above 10−25 atm, MnO particles in the form of the thermodynamic stable phase became coarser and tended to aggregate, which hindered the formation of a continuous inhibition layer, resulting in the defects of bare spots on the galvanized surface of the steel. When the oxygen partial pressure greater than 10−22 atm, film-like MnO layer was formed on the surface of steel sample, which obviously deteriorated the galvanizability. The galvanizability of the steel can be improved by the regulation of oxygen partial pressure; based on this, the reasonable zinc plating process parameters can be developed.
- 23 November 2016
- Published by Springer Nature in Advances in Manufacturing
- Vol. 4 (4) , 340-347
Application of thermodynamics in designing of advanced automotive steels
- 23 November 2016
- Published by Springer Nature in Advances in Manufacturing
- Vol. 4 (4) , 340-347
Application of thermodynamics in designing of advanced automotive steels
- 14 April 2011
- Published by Springer Nature
- p. 265-274
Microstructure and Property Control of Advanced High Strength Automotive Steels
- 14 April 2011
- Published by Springer Nature
- p. 265-274
Microstructure and Property Control of Advanced High Strength Automotive Steels
- 27 January 2010
- Published by Springer Nature in Frontiers of Materials Science in China
- Vol. 4 (1) , 100-102
Effects of high magnetic field on thermodynamic properties of pure Fe and Cu
- 27 January 2010
- Published by Springer Nature in Frontiers of Materials Science in China
- Vol. 4 (1) , 100-102
Effects of high magnetic field on thermodynamic properties of pure Fe and Cu
- 10 March 2009
- Published by Springer Nature in Frontiers of Materials Science in China
- Vol. 3 (1) , 33-37
Thermodynamic re-assessment of the Fe-Al-C system based on the Fe-rich experimental data
- 10 March 2009
- Published by Springer Nature in Frontiers of Materials Science in China
- Vol. 3 (1) , 33-37
Thermodynamic re-assessment of the Fe-Al-C system based on the Fe-rich experimental data