Omkaresh Byalakere Rudreshaiah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Omkaresh Byalakere Rudreshaiah has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Aisha Siddekha
Department of Chemistry, Government First Grade College, B.H. Road, Tumakuru-572 102, Karnataka, India
1 shared publicationAnasuya K V
1 shared publicationB. K. Sudharshan
Department of Mechanical Engineering, Siddaganga Institute of Technology, B. H. Road, Tumakuru – 572103, Karnataka
1 shared publication- Basir Maleki1 shared publication
C. L. Ujval
Department of Mechanical Engineering, Siddaganga Institute of Technology, B. H. Road, Tumakuru – 572103, Karnataka
1 shared publication- Gururaj Lalagi
M S Ramaiah Institute of Technology
1 shared publication
Latest Publications
- 13 January 2026
- Published by Taylor & Francis
- p. 194-203
Emerging Materials for Battery Management Systems
Electric vehicles (EVs) and hybrid electric vehicles (HEVs) are a promising solution in promoting carbon neutrality by withstanding climate crisis and providing environmental justice. The challenge is to address the cutting edge of battery technology and battery management systems (BMS,), which lies with the future technologies and breakthrough opportunities in battery materials for advancing electric mobility. The worldwide need for battery materials is growing significantly and is expected to continue for several years. Other factors such as recycling and second use will also affect the demand for materials in BMSs. To address these challenges, materials have evolved as a vital factor in storing electrochemical energy from ultra-capacitors to high specific energy batteries to fuel cells. Over time, battery materials have evolved and dominated the market, starting with lead–acid (mature technology, cheaper), Ni batteries (higher specific energy), lithium batteries (energy density, high specific energy), metal/air batteries (high specific energy, energy density), and flow batteries which are like fuel cells using different materials. The technological aspects of materials need to be explored for high energy storage. Zinc manganese oxide, nanobolt lithium tungsten, gold nanowire, gel electrolyte, organosilicon electrolyte, tank two-string cell batteries, and lithium-sulfur batteries are promising solutions as they are fast charging, affordable, and nontoxic.
- 13 January 2026
- Published by Taylor & Francis
- p. 194-203
Emerging Materials for Battery Management Systems
Electric vehicles (EVs) and hybrid electric vehicles (HEVs) are a promising solution in promoting carbon neutrality by withstanding climate crisis and providing environmental justice. The challenge is to address the cutting edge of battery technology and battery management systems (BMS,), which lies with the future technologies and breakthrough opportunities in battery materials for advancing electric mobility. The worldwide need for battery materials is growing significantly and is expected to continue for several years. Other factors such as recycling and second use will also affect the demand for materials in BMSs. To address these challenges, materials have evolved as a vital factor in storing electrochemical energy from ultra-capacitors to high specific energy batteries to fuel cells. Over time, battery materials have evolved and dominated the market, starting with lead–acid (mature technology, cheaper), Ni batteries (higher specific energy), lithium batteries (energy density, high specific energy), metal/air batteries (high specific energy, energy density), and flow batteries which are like fuel cells using different materials. The technological aspects of materials need to be explored for high energy storage. Zinc manganese oxide, nanobolt lithium tungsten, gold nanowire, gel electrolyte, organosilicon electrolyte, tank two-string cell batteries, and lithium-sulfur batteries are promising solutions as they are fast charging, affordable, and nontoxic.
- Open Access
- 23 November 2025
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
A facile plant-mediated green synthesis of Magnesium oxide nano particles by combustion method using Terminalia Chebula seed and their applications in the synthesis of selenoesters and biodiesel from used cooking oil
Synthesis of magnesium oxide nanoparticles (MgO NPs) using Terminalia chebula seeds extract as fuel by solution combustion method and their applications have been reported in this study. Characterization of the synthesized MgO NPs via Powder XRD, FT-IR, SEM, TEM and EDAX for structural and morphological studies was carried out. MgO NPs were used as a catalyst for production of biodiesel from used cooking oil and for the synthesis of selenoesters. The selenoesters were analyzed by mass spectrometry, 1H NMR, 13C NMR, FTIR techniques and the antifungal activity was investigated for some of the selenoesters against two pathogenic strains F. oxysporum and A. niger with Fluconazole as a standard drug. Biodiesel produced was tested for conformity with the ASTM standard and the results are reported herein. This is one of the novel methods reported for the synthesis of MgO NPs using terminalia chebula seeds, which are easily available, non-toxic, make the NPs green. Catalytic performance of these MgO NPs can be explored further for the synthesis of other organic compounds.
- 23 November 2025
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
Open AccessA facile plant-mediated green synthesis of Magnesium oxide nano particles by combustion method using Terminalia Chebula seed and their applications in the synthesis of selenoesters and biodiesel from used cooking oil
Synthesis of magnesium oxide nanoparticles (MgO NPs) using Terminalia chebula seeds extract as fuel by solution combustion method and their applications have been reported in this study. Characterization of the synthesized MgO NPs via Powder XRD, FT-IR, SEM, TEM and EDAX for structural and morphological studies was carried out. MgO NPs were used as a catalyst for production of biodiesel from used cooking oil and for the synthesis of selenoesters. The selenoesters were analyzed by mass spectrometry, 1H NMR, 13C NMR, FTIR techniques and the antifungal activity was investigated for some of the selenoesters against two pathogenic strains F. oxysporum and A. niger with Fluconazole as a standard drug. Biodiesel produced was tested for conformity with the ASTM standard and the results are reported herein. This is one of the novel methods reported for the synthesis of MgO NPs using terminalia chebula seeds, which are easily available, non-toxic, make the NPs green. Catalytic performance of these MgO NPs can be explored further for the synthesis of other organic compounds.
- 26 February 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (1) , 015562
Optimizing heat transfer in microchannel heat ex-changers: a comparative analysis of channel geometry and nanofluids through CFD and experimental approaches
This study uses CFD simulations and experimental methods to investigate the impact of channel geometry and nanofluid concentration on heat transfer performance in microchannel heat exchangers. Results show that increasing nanoparticle concentrations and mass flow rates enhance heat transfer in rectangular and circular channels. At a nanoparticle concentration of 0.05% and a Reynolds number of 500, circular channels demonstrated superior heat transfer performance compared to rectangular channels. Nusselt numbers increased by 18.16% for rectangular and 24.55% for circular channels on average. Pressure drops for both geometries also increased, with a 17.57% rise for rectangular and 16.74% for circular channels relative to the base fluid. Additionally, the pressure drop was 4.72% higher in rectangular channels than in circular ones. Lower Reynolds numbers significantly reduced friction factors, with the minimum friction observed at 0.01% nanofluid concentration. Circular channels exhibited lower friction than rectangular channels across different nanofluid concentrations. CFD and experimental results were in close agreement, particularly regarding pressure drop and temperature, confirming the accuracy of the analysis.
- 26 February 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (1) , 015562
Optimizing heat transfer in microchannel heat ex-changers: a comparative analysis of channel geometry and nanofluids through CFD and experimental approaches
This study uses CFD simulations and experimental methods to investigate the impact of channel geometry and nanofluid concentration on heat transfer performance in microchannel heat exchangers. Results show that increasing nanoparticle concentrations and mass flow rates enhance heat transfer in rectangular and circular channels. At a nanoparticle concentration of 0.05% and a Reynolds number of 500, circular channels demonstrated superior heat transfer performance compared to rectangular channels. Nusselt numbers increased by 18.16% for rectangular and 24.55% for circular channels on average. Pressure drops for both geometries also increased, with a 17.57% rise for rectangular and 16.74% for circular channels relative to the base fluid. Additionally, the pressure drop was 4.72% higher in rectangular channels than in circular ones. Lower Reynolds numbers significantly reduced friction factors, with the minimum friction observed at 0.01% nanofluid concentration. Circular channels exhibited lower friction than rectangular channels across different nanofluid concentrations. CFD and experimental results were in close agreement, particularly regarding pressure drop and temperature, confirming the accuracy of the analysis.
- Open Access
- 22 July 2024
- Published by Informatics Publishing Limited in Journal of Mines, Metals and Fuels
- p. 347-355
Influence of Welding Parameters on Weld Timings, Temperature Variation and Mechanical Strength of Friction Stir Welded AA6061 and AA6082 Alloy
Friction stir welding is a type of welding that creates friction using a stirring tool while the work-pieces are held together in the welding joint configuration. Friction stir welding is a solid-state welding process. It is one of the efficient ways of joining technology of materials. The friction forces at a microscopic level to change the inner structure of metal properties and it is done by using the kinetic energy of friction in welding methods. This work is majorly carried out to optimize the process parameters like tool rotational speed, Feed, ultimate tensile strength of friction stir welded joint on AA6061 and AA6082 alloy. Welding speed and temperature variation in the workpiece during the welding is recorded for different trials. Failure analysis was carried out for different fractured surfaces by using Scanning Electron Microscope (SEM) revels ductile fracture due to micro void coalescence. The maximum ultimate tensile strength was at a speed of 900 rpm, feed 31.5 mm/min indicates high joint efficiency. Welding speed is more at the feed 90mm/min. Maximum rise in the temperature is at speed 2000 rpm and feed 90 mm/min.
- 22 July 2024
- Published by Informatics Publishing Limited in Journal of Mines, Metals and Fuels
- p. 347-355
Open AccessInfluence of Welding Parameters on Weld Timings, Temperature Variation and Mechanical Strength of Friction Stir Welded AA6061 and AA6082 Alloy
Friction stir welding is a type of welding that creates friction using a stirring tool while the work-pieces are held together in the welding joint configuration. Friction stir welding is a solid-state welding process. It is one of the efficient ways of joining technology of materials. The friction forces at a microscopic level to change the inner structure of metal properties and it is done by using the kinetic energy of friction in welding methods. This work is majorly carried out to optimize the process parameters like tool rotational speed, Feed, ultimate tensile strength of friction stir welded joint on AA6061 and AA6082 alloy. Welding speed and temperature variation in the workpiece during the welding is recorded for different trials. Failure analysis was carried out for different fractured surfaces by using Scanning Electron Microscope (SEM) revels ductile fracture due to micro void coalescence. The maximum ultimate tensile strength was at a speed of 900 rpm, feed 31.5 mm/min indicates high joint efficiency. Welding speed is more at the feed 90mm/min. Maximum rise in the temperature is at speed 2000 rpm and feed 90 mm/min.
- Open Access
- 30 December 2023
- Published by Informatics Publishing Limited in Journal of Mines, Metals and Fuels
- p. 247-252
Purification of Glycerol Obtained during Biodiesel Synthesis and Production of Value - Added Product
Globally biodiesel is one of the best alternative fuels, and is seeing an exponential increase in demand. Despite the bright prospect of biodiesel production, efforts to commercialize it has been very limited. One of the major obstacles has been the high price associated with total production costs. Thus, it is necessary to reduce its processing cost to make biodiesel production feasible. This can be achieved by giving a value-added application for its byproduct. Glycerol is produced as an approximately 10-15% as a byproduct of the transesterification of triglycerides. Glycerol is a valuable byproduct obtained during biodiesel production but it is obtained in a crude form limiting its application. This byproduct needs to be purified efficiently to utilize it. Therefore, the present work aims to report phases in which the crude glycerol is purified. There are two phases in which the crude glycerol is purified. The Crude Glycerol is processed through saponification and then neutralization in the first phase. This produces three layers from which partly purified glycerol is obtained through separation. In the second phase of purification, the glycerol layer is separated from various salt impurities by the use of non-polar solvents. This glycerol is then extracted from the solvent and is subjected to decolorization using charcoal. Soaps and detergents are prepared as a valueadded product from the obtained glycerol.
- 30 December 2023
- Published by Informatics Publishing Limited in Journal of Mines, Metals and Fuels
- p. 247-252
Open AccessPurification of Glycerol Obtained during Biodiesel Synthesis and Production of Value - Added Product
Globally biodiesel is one of the best alternative fuels, and is seeing an exponential increase in demand. Despite the bright prospect of biodiesel production, efforts to commercialize it has been very limited. One of the major obstacles has been the high price associated with total production costs. Thus, it is necessary to reduce its processing cost to make biodiesel production feasible. This can be achieved by giving a value-added application for its byproduct. Glycerol is produced as an approximately 10-15% as a byproduct of the transesterification of triglycerides. Glycerol is a valuable byproduct obtained during biodiesel production but it is obtained in a crude form limiting its application. This byproduct needs to be purified efficiently to utilize it. Therefore, the present work aims to report phases in which the crude glycerol is purified. There are two phases in which the crude glycerol is purified. The Crude Glycerol is processed through saponification and then neutralization in the first phase. This produces three layers from which partly purified glycerol is obtained through separation. In the second phase of purification, the glycerol layer is separated from various salt impurities by the use of non-polar solvents. This glycerol is then extracted from the solvent and is subjected to decolorization using charcoal. Soaps and detergents are prepared as a valueadded product from the obtained glycerol.
- 30 November 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 27 (13) , 14432-14440
Terminalia bellirica: a new biodiesel for diesel engine: a comparative experimental investigation
In the present study, Terminalia bellirica methyl ester (TBME)/biodiesel was formed using potassium hydroxide as catalyst. Methyl ester fuel properties were resolved as per ASTM standard. The attribute of compression ignition (CI) engine such as combustion, performance, and released emission qualities of samples, such as diesel and TBME blends (B10, B20, B30, B50, and B100), were deliberated on a single-cylinder CI engine. By varying the load to 0%, 25%, 50%, 75%, and 100%, test data were measured. Using AVL DI GAS 444N (five gas) analyzer dissimilarity in the engine emissions were documented. The results of biodiesel test blends show the similar combustion and performance to diesel curves with minor decrement. However, CO and HC emission diminish when engine fueled with TBME test blends whereas NOx amplifies.
- 30 November 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 27 (13) , 14432-14440
Terminalia bellirica: a new biodiesel for diesel engine: a comparative experimental investigation
In the present study, Terminalia bellirica methyl ester (TBME)/biodiesel was formed using potassium hydroxide as catalyst. Methyl ester fuel properties were resolved as per ASTM standard. The attribute of compression ignition (CI) engine such as combustion, performance, and released emission qualities of samples, such as diesel and TBME blends (B10, B20, B30, B50, and B100), were deliberated on a single-cylinder CI engine. By varying the load to 0%, 25%, 50%, 75%, and 100%, test data were measured. Using AVL DI GAS 444N (five gas) analyzer dissimilarity in the engine emissions were documented. The results of biodiesel test blends show the similar combustion and performance to diesel curves with minor decrement. However, CO and HC emission diminish when engine fueled with TBME test blends whereas NOx amplifies.