Yigong Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yigong Shi has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Bo Wu
Western Superconducting Technologies (WST) Company Ltd., Xian, China
13 shared publications - Qiang Guo
Western Superconducting Technologies (WST) Company Ltd., Xian, China
11 shared publications Pingxiang Zhang
Western Superconducting Technologies (WST) Company Ltd., Xian, China
9 shared publicationsJianfeng Li
Northwest Institute for Non-Ferrous Metal Research, Xian, China
7 shared publicationsXianghong Liu
Western Superconducting Technologies (WST) Company Ltd., Xian, China
7 shared publicationsYong Feng
Western Superconducting Technologies (WST) Company Ltd., Xian, China
7 shared publications
Latest Publications
- 5 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-4
The Electromagnetic Properties of Multi-Filaments MgB 2 Wires
Reducing the AC loss of MgB2 wire is significant for its possible AC engineering applications. In this study, the multi filaments MgB2 wires possessed of various filaments diameter were fabricated via in-situ PIT (Powder in Tube) method. The effects of filaments diameters on the superconducting properties and magnetic hysteresis loss of MgB2 wires were studied systematically. With the filaments diameters decrease from 120 μm to 40 μm, the critical current density (Jc) decreases by 20% (4.2 K, 3 T), the critical transition temperature (Tc) shows a consistent trend, while the magnetic hysteresis losses (Qm) decrease from 1230 mJ/cm3 to 650 mJ/cm3. The above results demonstrate that the smaller filaments diameter is beneficial to reduce the Qm of MgB2 wire, but the attenuation of current capacity can also not be ignored
- 5 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-4
The Electromagnetic Properties of Multi-Filaments MgB 2 Wires
Reducing the AC loss of MgB2 wire is significant for its possible AC engineering applications. In this study, the multi filaments MgB2 wires possessed of various filaments diameter were fabricated via in-situ PIT (Powder in Tube) method. The effects of filaments diameters on the superconducting properties and magnetic hysteresis loss of MgB2 wires were studied systematically. With the filaments diameters decrease from 120 μm to 40 μm, the critical current density (Jc) decreases by 20% (4.2 K, 3 T), the critical transition temperature (Tc) shows a consistent trend, while the magnetic hysteresis losses (Qm) decrease from 1230 mJ/cm3 to 650 mJ/cm3. The above results demonstrate that the smaller filaments diameter is beneficial to reduce the Qm of MgB2 wire, but the attenuation of current capacity can also not be ignored
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-4
Effect of the Design on the Mechanical Properties of Internal-Tin Nb 3 Sn Superconducting Strand
Compared with the bronze process, Nb3Sn strands prepared by the internal-tin (IT) process have higher Sn contents and can generate more Nb3Sn phases, making it the main method for preparing Nb3Sn strands with high critical current density. The Nb3Sn phase formed after heat treatment is a brittle intermetallic compound, and the filament damage and performance degradation under low-temperature and high-magnetic-field conditions need attention. During use, the compression and tensile strains on the strand can lead to performance attenuation. Therefore, it is important to study the relationship between performance degradation and the preparation process for the practical application of the strand. By optimizing the strand design and heat treatments, we prepared Nb3Sn strands with different mechanical properties. The critical current densities under different magnetic fields were tested. The internal local strain of the filaments was analyzed, and the relationship between heat treatments, and the mechanical properties of the strand were improved, enhancing its engineering application prospects.
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-4
Effect of the Design on the Mechanical Properties of Internal-Tin Nb 3 Sn Superconducting Strand
Compared with the bronze process, Nb3Sn strands prepared by the internal-tin (IT) process have higher Sn contents and can generate more Nb3Sn phases, making it the main method for preparing Nb3Sn strands with high critical current density. The Nb3Sn phase formed after heat treatment is a brittle intermetallic compound, and the filament damage and performance degradation under low-temperature and high-magnetic-field conditions need attention. During use, the compression and tensile strains on the strand can lead to performance attenuation. Therefore, it is important to study the relationship between performance degradation and the preparation process for the practical application of the strand. By optimizing the strand design and heat treatments, we prepared Nb3Sn strands with different mechanical properties. The critical current densities under different magnetic fields were tested. The internal local strain of the filaments was analyzed, and the relationship between heat treatments, and the mechanical properties of the strand were improved, enhancing its engineering application prospects.
- 20 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-4
Study on the Fracture Mode of Nb 3 Sn Wire
Nb3Sn wire is a low-temperature superconducting material with tremendous development potential due to its high critical magnetic field and current carrying density. It has been extensively used in a variety of applications, including huge particle accelerators, superconducting energy storage systems, and magnetic confinement nuclear fusion devices. The internal-tin Nb3Sn wire is made of copper, niobium, tantalum, and tin. Its structure is more complex than that of NbTi wire, making it difficult to determine the exact cause of fracture. This intricacy significantly impedes the study and production of Nb3Sn wire. In this work, a high-resolution X-ray tomography equipment was used to scan and recreate the Nb3Sn fracture. Then we analyzed the sample after atepwise polishing using a scaning eletron microscope (SEM) to verify the aforementioned results. We study the various fracture modes of the wire and discover the causes of the fractures. We present a fracture analysis approach for determining the source of cracks. The fracture can be split into three parts: the fracture source region, the fracture expansion region, and the ultimate fracture region. The genesis of the fracture source and expansion model were investigated using microstructure data.
- 20 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-4
Study on the Fracture Mode of Nb 3 Sn Wire
Nb3Sn wire is a low-temperature superconducting material with tremendous development potential due to its high critical magnetic field and current carrying density. It has been extensively used in a variety of applications, including huge particle accelerators, superconducting energy storage systems, and magnetic confinement nuclear fusion devices. The internal-tin Nb3Sn wire is made of copper, niobium, tantalum, and tin. Its structure is more complex than that of NbTi wire, making it difficult to determine the exact cause of fracture. This intricacy significantly impedes the study and production of Nb3Sn wire. In this work, a high-resolution X-ray tomography equipment was used to scan and recreate the Nb3Sn fracture. Then we analyzed the sample after atepwise polishing using a scaning eletron microscope (SEM) to verify the aforementioned results. We study the various fracture modes of the wire and discover the causes of the fractures. We present a fracture analysis approach for determining the source of cracks. The fracture can be split into three parts: the fracture source region, the fracture expansion region, and the ultimate fracture region. The genesis of the fracture source and expansion model were investigated using microstructure data.
- 19 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Study on the Influence of Ta and Zr Addition on the Diffusion Reaction of Nb 3 Sn
In commercial Nb3Sn wires, the Nb3Sn phase is formed by a solid-state diffusion reaction. As one of the reaction precursor materials, parent Nb-alloys are closely related to the quality of the formed Nb3Sn. The properties of niobium can be significantly modified by element doping. In this work, Nb-Ta and Nb-Zr alloys, along with pure Nb, were utilized to manufacture single Tube-type sub-elements for systematically studying the influence of Ta and Zr doping on the diffusion reaction of Nb3Sn. During the high-temperature stage, various heat treatment temperatures were applied to the samples. The Nb3Sn grain size, growth rate of the Nb3Sn layer, and the critical field and temperature are characterized and analyzed. It was found that Zr doping promotes the diffusion reaction in Nb3Sn more effectively than Ta doping. As the heat treatment temperature increases, the effect of Ta doping on promoting the diffusion reaction weakens. Zr demonstrates a significant effect on refining Nb3Sn grains, while Ta shows no grain refinement effect. As the temperature rises, the grain refinement effect of Zr doping becomes more pronounced. Both Ta and Zr doping can enhance the upper critical field of Nb3Sn, with Ta being more effective in this regard than Zr.
- 19 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Study on the Influence of Ta and Zr Addition on the Diffusion Reaction of Nb 3 Sn
In commercial Nb3Sn wires, the Nb3Sn phase is formed by a solid-state diffusion reaction. As one of the reaction precursor materials, parent Nb-alloys are closely related to the quality of the formed Nb3Sn. The properties of niobium can be significantly modified by element doping. In this work, Nb-Ta and Nb-Zr alloys, along with pure Nb, were utilized to manufacture single Tube-type sub-elements for systematically studying the influence of Ta and Zr doping on the diffusion reaction of Nb3Sn. During the high-temperature stage, various heat treatment temperatures were applied to the samples. The Nb3Sn grain size, growth rate of the Nb3Sn layer, and the critical field and temperature are characterized and analyzed. It was found that Zr doping promotes the diffusion reaction in Nb3Sn more effectively than Ta doping. As the heat treatment temperature increases, the effect of Ta doping on promoting the diffusion reaction weakens. Zr demonstrates a significant effect on refining Nb3Sn grains, while Ta shows no grain refinement effect. As the temperature rises, the grain refinement effect of Zr doping becomes more pronounced. Both Ta and Zr doping can enhance the upper critical field of Nb3Sn, with Ta being more effective in this regard than Zr.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Optimization of Critical Current Density at 16 Tesla in Nb 3 Sn Superconducting Wires Fabricated in WST
To develop superconducting wires suitable for applications demanding extremely high magnetic fields, we conducted an experimental investigation on the optimization of microstructure and heat treatment processes aimed at enhancing the critical current density (non-Cu Jc) at 16 T in Internal-tin type multifilamentary Nb3Sn superconducting wires fabricated in WST. Our findings revealed that, under optimal growth conditions characterized by specific time and temperature parameters, where Nb3Sn grain size increased slightly, Hirr demonstrated a relatively higher value, we obtained significantly enhanced performance at 16 T in these Nb3Sn wires. Specifically, by fine-tuning the Nb3Sn growth condition to 680°C for 80 h, we achieved an impressive Hirr of 27.42 T (4.2 K), and non-Cu Jc was elevated to values exceeding 1300 A/mm2 (4.2 K, 16 T), accompanied by an atomic percentage of Sn in Nb3Sn reaching 24at.%, conditions conducive to Sn-rich Nb3Sn phases, representing one of the highest performances reported thus far for Ti-doped Nb3Sn wires. We have thus offered a new, scalable route to further study the enhancement of Jc in Nb3Sn wires.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Optimization of Critical Current Density at 16 Tesla in Nb 3 Sn Superconducting Wires Fabricated in WST
To develop superconducting wires suitable for applications demanding extremely high magnetic fields, we conducted an experimental investigation on the optimization of microstructure and heat treatment processes aimed at enhancing the critical current density (non-Cu Jc) at 16 T in Internal-tin type multifilamentary Nb3Sn superconducting wires fabricated in WST. Our findings revealed that, under optimal growth conditions characterized by specific time and temperature parameters, where Nb3Sn grain size increased slightly, Hirr demonstrated a relatively higher value, we obtained significantly enhanced performance at 16 T in these Nb3Sn wires. Specifically, by fine-tuning the Nb3Sn growth condition to 680°C for 80 h, we achieved an impressive Hirr of 27.42 T (4.2 K), and non-Cu Jc was elevated to values exceeding 1300 A/mm2 (4.2 K, 16 T), accompanied by an atomic percentage of Sn in Nb3Sn reaching 24at.%, conditions conducive to Sn-rich Nb3Sn phases, representing one of the highest performances reported thus far for Ti-doped Nb3Sn wires. We have thus offered a new, scalable route to further study the enhancement of Jc in Nb3Sn wires.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-4
Study on the Improving the Uniformity of Ti Distribution in New Type of High J c Nb 3 Sn Wire Produced by WST
High Jc Nb3Sn superconducting wires is mainly used in the preparation of high field magnets because of its higher critical current density. Further improving the critical current density of Nb3Sn wire, reducing the use amount of wire in magnets is one of important ways to promote the industrialization and mass application of High Jc Nb3Sn wire. It is known that doping Ti in Nb3Sn phase can improve the critical magnetic field effectively, refine the Nb3Sn grains, and improve the critical current density. Too much or too little Ti will greatly reduce the doping effect. The Ti diffusion is later than the Nb3Sn phase reaction under three-zone section heat treatment, so the distribution of Ti in Nb3Sn phase is uneven. This paper introduces a new heat treatment process, which can improve the uniformity of Ti in Nb3Sn phase by adding an insulation platform between the medium temperature and high temperature insulation platform. Eventually, the critical current density of the High Jc Nb3Sn wire was improved, reaching 2938 A/mm2.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-4
Study on the Improving the Uniformity of Ti Distribution in New Type of High J c Nb 3 Sn Wire Produced by WST
High Jc Nb3Sn superconducting wires is mainly used in the preparation of high field magnets because of its higher critical current density. Further improving the critical current density of Nb3Sn wire, reducing the use amount of wire in magnets is one of important ways to promote the industrialization and mass application of High Jc Nb3Sn wire. It is known that doping Ti in Nb3Sn phase can improve the critical magnetic field effectively, refine the Nb3Sn grains, and improve the critical current density. Too much or too little Ti will greatly reduce the doping effect. The Ti diffusion is later than the Nb3Sn phase reaction under three-zone section heat treatment, so the distribution of Ti in Nb3Sn phase is uneven. This paper introduces a new heat treatment process, which can improve the uniformity of Ti in Nb3Sn phase by adding an insulation platform between the medium temperature and high temperature insulation platform. Eventually, the critical current density of the High Jc Nb3Sn wire was improved, reaching 2938 A/mm2.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Effect of Titanium Content and Doping Method on Phase Formation and Properties of Nb3Sn Strand
Doping with Ti is crucial for enhancing the upper critical field of Nb3Sn strand produced by internal tin process. This study investigates the effects of different Ti doping methods and concentrations on the low-temperature performance of Nb3Sn strand. We compare two methods: one replaces Nb cores with NbTi cores, while the other integrates Ti into Sn ingots to form SnTi alloys, with adjustable Ti content. Four Nb3Sn strand with varying Ti concentrations were produced using these methods. Microstructural and performance tests show that Ti doping refines Nb3Sn grains. Jc increases with Ti content from 0% to 2%, but decreases beyond 2% due to grain growth from excessive Ti. Additionally, the larger Ti6Sn5 phase in the SnTi alloy results in more breakage during processing. Thus, using SnCu alloy as the Sn source and NbTi rods for Ti doping is a more feasible approach for the production of Nb3Sn strands.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Effect of Titanium Content and Doping Method on Phase Formation and Properties of Nb3Sn Strand
Doping with Ti is crucial for enhancing the upper critical field of Nb3Sn strand produced by internal tin process. This study investigates the effects of different Ti doping methods and concentrations on the low-temperature performance of Nb3Sn strand. We compare two methods: one replaces Nb cores with NbTi cores, while the other integrates Ti into Sn ingots to form SnTi alloys, with adjustable Ti content. Four Nb3Sn strand with varying Ti concentrations were produced using these methods. Microstructural and performance tests show that Ti doping refines Nb3Sn grains. Jc increases with Ti content from 0% to 2%, but decreases beyond 2% due to grain growth from excessive Ti. Additionally, the larger Ti6Sn5 phase in the SnTi alloy results in more breakage during processing. Thus, using SnCu alloy as the Sn source and NbTi rods for Ti doping is a more feasible approach for the production of Nb3Sn strands.
- 28 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Study on the High Temperature Heat Treatment Process Optimization of Different Sizes High Jc Nb$_{\text{3}}$Sn Wire Produced by WST
The heat treatment process plays a central role in optimizing the critical current density of Nb 3 Sn wire. Increasing the critical current density of Nb 3 Sn wire, reducing the use amount of wire in magnets and reducing the price are important ways to promote the industrialization and mass application of Nb 3 Sn wire. The Nb 3 Sn microstructure state in the wire and an even distribution of Ti are critical factors for enhancing the current density of the wire. The grain size of the Nb 3 Sn wire increases with the rise in heat treatment temperature. Therefore, the optimum temperature should be the lowest that ensures the full reaction/diffusion of each element.So the optimum third plateau heat treatment process of different size high Jc Nb 3 Sn wire is: (1) the third plateau of outer diameter 0.82 mm wire is 640 °C, and the holding time is 50 h; (2) the third plateau of outer diameter 0.99 mm wire is 665 °C, and the holding time is 50 h; (3) the third plateau of outer diameter 1.30 mm wire is 665 °C, and the holding time is 80 h. The average critical current density of the wire, measured at 12 T and 4.22 K, has been increased from 2500 A/mm 2 to 2600 A/mm 2 .
- 28 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Study on the High Temperature Heat Treatment Process Optimization of Different Sizes High Jc Nb$_{\text{3}}$Sn Wire Produced by WST
The heat treatment process plays a central role in optimizing the critical current density of Nb 3 Sn wire. Increasing the critical current density of Nb 3 Sn wire, reducing the use amount of wire in magnets and reducing the price are important ways to promote the industrialization and mass application of Nb 3 Sn wire. The Nb 3 Sn microstructure state in the wire and an even distribution of Ti are critical factors for enhancing the current density of the wire. The grain size of the Nb 3 Sn wire increases with the rise in heat treatment temperature. Therefore, the optimum temperature should be the lowest that ensures the full reaction/diffusion of each element.So the optimum third plateau heat treatment process of different size high Jc Nb 3 Sn wire is: (1) the third plateau of outer diameter 0.82 mm wire is 640 °C, and the holding time is 50 h; (2) the third plateau of outer diameter 0.99 mm wire is 665 °C, and the holding time is 50 h; (3) the third plateau of outer diameter 1.30 mm wire is 665 °C, and the holding time is 80 h. The average critical current density of the wire, measured at 12 T and 4.22 K, has been increased from 2500 A/mm 2 to 2600 A/mm 2 .
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Development of Internal Tin Nb3Sn Strand for CRAFT in WST
Western Superconducting Technologies Co. Ltd. (WST) has developed several types of internal tin (IT) process Nb 3 Sn strands for the Comprehensive Research Facility for Fusion Technology (CRAFT) project. By increasing the number of niobium filaments and the tin content, the Nb 3 Sn phase was more effectively formed after heat treatment, thereby enhancing the critical current of the strands. The distribution of the niobium filaments was also optimized to minimize hysteresis loss. To date, WST has prepared over twenty tons of strands with a diameter of 0.99 mm for toroidal field (TF) coils. The critical current ranges from 370 A to 450 A at 12 T and 4.2 K. Additionally, the hysteresis loss ranges from 272 mJ/cm 3 to 567 mJ/cm 3 at ± 3 T and 4.2 K. Compared to ITER strands, the average hysteresis loss of 432 mJ/cm 3 was reduced by 10%. Furthermore, approximately eight tons of strands with a diameter of 0.82 mm have been produced for Superconducting Conductor Testing Facility. The critical current ranges from 293 A to 359 A at 12 T and 4.2 K, which is 20% higher on average than that of ITER strands. All the performances of the strands fabricated by WST meet the requirements of CRAFT project.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Development of Internal Tin Nb3Sn Strand for CRAFT in WST
Western Superconducting Technologies Co. Ltd. (WST) has developed several types of internal tin (IT) process Nb 3 Sn strands for the Comprehensive Research Facility for Fusion Technology (CRAFT) project. By increasing the number of niobium filaments and the tin content, the Nb 3 Sn phase was more effectively formed after heat treatment, thereby enhancing the critical current of the strands. The distribution of the niobium filaments was also optimized to minimize hysteresis loss. To date, WST has prepared over twenty tons of strands with a diameter of 0.99 mm for toroidal field (TF) coils. The critical current ranges from 370 A to 450 A at 12 T and 4.2 K. Additionally, the hysteresis loss ranges from 272 mJ/cm 3 to 567 mJ/cm 3 at ± 3 T and 4.2 K. Compared to ITER strands, the average hysteresis loss of 432 mJ/cm 3 was reduced by 10%. Furthermore, approximately eight tons of strands with a diameter of 0.82 mm have been produced for Superconducting Conductor Testing Facility. The critical current ranges from 293 A to 359 A at 12 T and 4.2 K, which is 20% higher on average than that of ITER strands. All the performances of the strands fabricated by WST meet the requirements of CRAFT project.
- 23 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Investigation on the Recrystallization and Nb3Sn Microstructure of Nb Alloys With Large Deformation During Heat Treatment
At fields of greater than 10 T, Nb 3 Sn wires with high critical current density are commercially available and has been used to manufacture high field magnets. In such wires, Nb or Nb alloys are drawn with a large reduction to micrometer scale, resulting in high work hardening, and the Nb 3 Sn A15 phase is produced by a heat treatment. After the heat treatment, Nb 3 Sn A15 phase was generated within Nb or Nb alloys. In this study Nb and Nb-Ta-Zr alloys were used to process Nb 3 Sn wire. The microstructure and the hardness were investigated during wire drawing process. After large deformation the grains of Nb filaments were elongated to fiber texture. The heat treatments of Nb 3 Sn wires were used to study the recrystallization and Nb 3 Sn phase formation within Nb alloys. The results showed that with high deformation the hardness of Nb-Ta-Zr alloy increased more and higher than the pure Nb about 70∼90 Hv with the same strain. During the high temperature heat treatment smaller grains about 100 nm in diameter of Nb 3 Sn were produced within Nb-Ta-Zr alloy. Recrystallization proceeded less readily for Nb-Ta-Zr than pure Nb, and at the heat treatment temperature pure Nb grains coarsen to micrometer scale.
- 23 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Investigation on the Recrystallization and Nb3Sn Microstructure of Nb Alloys With Large Deformation During Heat Treatment
At fields of greater than 10 T, Nb 3 Sn wires with high critical current density are commercially available and has been used to manufacture high field magnets. In such wires, Nb or Nb alloys are drawn with a large reduction to micrometer scale, resulting in high work hardening, and the Nb 3 Sn A15 phase is produced by a heat treatment. After the heat treatment, Nb 3 Sn A15 phase was generated within Nb or Nb alloys. In this study Nb and Nb-Ta-Zr alloys were used to process Nb 3 Sn wire. The microstructure and the hardness were investigated during wire drawing process. After large deformation the grains of Nb filaments were elongated to fiber texture. The heat treatments of Nb 3 Sn wires were used to study the recrystallization and Nb 3 Sn phase formation within Nb alloys. The results showed that with high deformation the hardness of Nb-Ta-Zr alloy increased more and higher than the pure Nb about 70∼90 Hv with the same strain. During the high temperature heat treatment smaller grains about 100 nm in diameter of Nb 3 Sn were produced within Nb-Ta-Zr alloy. Recrystallization proceeded less readily for Nb-Ta-Zr than pure Nb, and at the heat treatment temperature pure Nb grains coarsen to micrometer scale.