Steffen Holland
Research Subjects
Steffen Holland has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- David Pommerenke
Graz University of Technology
8 shared publications - Guido Notermans
Nexperia Germany GmbH, Hamburg, Germany
6 shared publications - Hans-Martin Ritter
Nexperia Germany GmbH, Hamburg, Germany
6 shared publications - Daryl G. Beetner
EMC Laboratory, Missouri University of Science and Technology, Rolla, MO, USA
5 shared publications - Jianchi Zhou
EMC Laboratory, Missouri University of Science and Technology, Rolla, MO, USA
4 shared publications Sergej Bub
Nexperia Germany GmbH, Hamburg, Germany
4 shared publications
Latest Publications
- Open Access
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7281-7286
I – V Hysteresis in ESD Protection SCR Due to Jumping Between Bulk and Surface Current Paths
The origin of an I – V hysteresis and sharp snapback of single finger silicon-controlled rectifiers (SCRs) for system-level electrostatic discharge (ESD) protection is investigated experimentally and by 2-D technology computer-aided design (TCAD) simulation. Emission microscopy (EMMI) measurements indicate spatial changes in current flow, which is reproduced in simulations using up and down current sweeps. A bulk current path, via two serially connected n-p-n transistors, comprising buried layers (BLs) gives rise to a high-voltage I – V (HV-IV) branch. The sharp snapback is caused by a sudden jump of the current path from the bulk to surface region, thus activating the SCR. The TCAD reveals that charge conditions at the surface determine the stability of the bulk path, and thus the existence of the hysteresis, via the location of impact ionization generation source. The results are important for understanding the complex interplay and coupling of parallel current paths in SCRs.
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7281-7286
Open AccessI – V Hysteresis in ESD Protection SCR Due to Jumping Between Bulk and Surface Current Paths
The origin of an I – V hysteresis and sharp snapback of single finger silicon-controlled rectifiers (SCRs) for system-level electrostatic discharge (ESD) protection is investigated experimentally and by 2-D technology computer-aided design (TCAD) simulation. Emission microscopy (EMMI) measurements indicate spatial changes in current flow, which is reproduced in simulations using up and down current sweeps. A bulk current path, via two serially connected n-p-n transistors, comprising buried layers (BLs) gives rise to a high-voltage I – V (HV-IV) branch. The sharp snapback is caused by a sudden jump of the current path from the bulk to surface region, thus activating the SCR. The TCAD reveals that charge conditions at the surface determine the stability of the bulk path, and thus the existence of the hysteresis, via the location of impact ionization generation source. The results are important for understanding the complex interplay and coupling of parallel current paths in SCRs.
- 13 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (9) , 5051-5059
Modeling of TVS Diode Harmonic Distortion Using Piecewise Linear Capacitance
When used in RF applications, TVS diodes exhibit harmonic distortion due to their nonlinear capacitance and other effects. This article presents an approach to modeling harmonic distortion caused by TVS diodes using nonlinear capacitance. The approach is novel in the sense that it is highly automatable, computationally cheap, and generic. First, the harmonic distortion measurements are described. Then, the capacitor model is introduced and its harmonic distortion is analyzed analytically. A fitting procedure is described to convert the observed harmonic distortion into the coefficients of the model. Finally, the process is demonstrated on real data and the models were tested against an experiment.
- 13 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (9) , 5051-5059
Modeling of TVS Diode Harmonic Distortion Using Piecewise Linear Capacitance
When used in RF applications, TVS diodes exhibit harmonic distortion due to their nonlinear capacitance and other effects. This article presents an approach to modeling harmonic distortion caused by TVS diodes using nonlinear capacitance. The approach is novel in the sense that it is highly automatable, computationally cheap, and generic. First, the harmonic distortion measurements are described. Then, the capacitor model is introduced and its harmonic distortion is analyzed analytically. A fitting procedure is described to convert the observed harmonic distortion into the coefficients of the model. Finally, the process is demonstrated on real data and the models were tested against an experiment.
- 4 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 14, 1-6
Harmonic Distortion Reference Structure for Contact Induced Harmonics
Today's mobile device designs make extensive use of electrical interconnects, ESD protection and magnetic materials, all of which can be potential sources of interference due to harmonic distortion from strong TX signals due to non-linearities. Harmonic generation, particularly from contacts, is highly variable. Therefore, a stable and controllable harmonic reference source is required for nonlinear interference analysis in such devices. This paper proposes a harmonic reference source based on the Schottky diode. It produces consistent and adjustable distortion. Simulations agree very well with measurements up to the low gigahertz range. This allows validation and comparison in difficult environments such as contact harmonics in mobile phones.
- 4 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 14, 1-6
Harmonic Distortion Reference Structure for Contact Induced Harmonics
Today's mobile device designs make extensive use of electrical interconnects, ESD protection and magnetic materials, all of which can be potential sources of interference due to harmonic distortion from strong TX signals due to non-linearities. Harmonic generation, particularly from contacts, is highly variable. Therefore, a stable and controllable harmonic reference source is required for nonlinear interference analysis in such devices. This paper proposes a harmonic reference source based on the Schottky diode. It produces consistent and adjustable distortion. Simulations agree very well with measurements up to the low gigahertz range. This allows validation and comparison in difficult environments such as contact harmonics in mobile phones.
- 22 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (5) , 1273-1281
A Physics-Based Model for Snapback-Type ESD Protection Devices
A simplified physical-based model for deep-snapback transient voltage suppressors (TVS) is developed in this article. While based on physics, the number of parameters and components is minimized, so the model can be tuned easily from available measurements of the packaged TVS. SPICE convergence issues seen in previous snapback device models are eliminated by adding nonlinear damping components to the model. No convergence issues were seen among any of the simulations performed for this study, which includes transmission-line pulse tests with multiple levels and rise times. The proposed model was used to represent two different TVS devices and was validated in both device- and system-level simulations. Simulations of quasi-static and transient behavior matched measurement results within about 20% among all the tested cases.
- 22 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (5) , 1273-1281
A Physics-Based Model for Snapback-Type ESD Protection Devices
A simplified physical-based model for deep-snapback transient voltage suppressors (TVS) is developed in this article. While based on physics, the number of parameters and components is minimized, so the model can be tuned easily from available measurements of the packaged TVS. SPICE convergence issues seen in previous snapback device models are eliminated by adding nonlinear damping components to the model. No convergence issues were seen among any of the simulations performed for this study, which includes transmission-line pulse tests with multiple levels and rise times. The proposed model was used to represent two different TVS devices and was validated in both device- and system-level simulations. Simulations of quasi-static and transient behavior matched measurement results within about 20% among all the tested cases.
- 5 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (3) , 625-633
Improved SEED Modeling of an ESD Discharge to a USB Cable
Integrated circuits (ICs) connected to a universal serial bus (USB) interface require robust electrostatic discharge (ESD) protection strategies due to the nature of the high-speed interface and the regular access by users. System-efficient ESD design (SEED) simulations can help predict the level of ESD stress seen by the IC when protected by a transient voltage suppressor (TVS). In the following paper, previously developed models were improved to predict the voltage and current seen by a TVS and an on-chip protection diode when an ESD gun was discharged to one USB cable pin. Models were improved, in part, by accurately modeling the conductivity modulation within the behavioral TVS model and by using a measured equivalent source to represent the complex interaction between the ESD gun, USB cable, and enclosure. The response of the TVS and on-chip diode was studied in simulation and measurement for several cable configurations and when adding passive components between the TVS and on-chip diode. Simulations predicted peak and quasi-static voltages and currents at the TVS and on-chip diode within 30% of those seen in measurements. The proposed modeling process can help engineers to evaluate and optimize the effectiveness of their ESD protection strategies under complicated test conditions.
- 5 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (3) , 625-633
Improved SEED Modeling of an ESD Discharge to a USB Cable
Integrated circuits (ICs) connected to a universal serial bus (USB) interface require robust electrostatic discharge (ESD) protection strategies due to the nature of the high-speed interface and the regular access by users. System-efficient ESD design (SEED) simulations can help predict the level of ESD stress seen by the IC when protected by a transient voltage suppressor (TVS). In the following paper, previously developed models were improved to predict the voltage and current seen by a TVS and an on-chip protection diode when an ESD gun was discharged to one USB cable pin. Models were improved, in part, by accurately modeling the conductivity modulation within the behavioral TVS model and by using a measured equivalent source to represent the complex interaction between the ESD gun, USB cable, and enclosure. The response of the TVS and on-chip diode was studied in simulation and measurement for several cable configurations and when adding passive components between the TVS and on-chip diode. Simulations predicted peak and quasi-static voltages and currents at the TVS and on-chip diode within 30% of those seen in measurements. The proposed modeling process can help engineers to evaluate and optimize the effectiveness of their ESD protection strategies under complicated test conditions.
- 14 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (6) , 1802-1811
Characterization and Modeling of Commercial ICs for System-Efficient ESD Design
Optimizing electrostatic discharge (ESD) protection strategies requires simulation models of both on - and off -die ESD devices, but detailed information about on -die ESD protection is rarely available. Methods are proposed in the following paper to characterize and model the on -chip ESD protection using only measurements, with minimal a priori information about how the protection is implemented. The characterization targets a three-terminal (rather than the traditional two-terminal) protection structure, including the I/O, Vdd, Vss pins, and allows for current to flow between multiple pins simultaneously. A previously-developed behavioral model for TVS devices is used to capture the ESD behavior of the integrated circuit (IC), including its linear, quasi-static, and transient nonlinear response. The approach is used to model the equivalent current that flows through the on -chip ESD protection of two commercial ICs. The model of the on -chip ESD protection is combined with a behavioral model of an off -chip transient voltage suppressor to demonstrate their combined performance in a system-efficient ESD design (SEED) simulation. The model is validated both when the IC is powered- off and powered- on . The SEED model was able to predict quasistatic and peak voltages and currents at the IC with less than a 10% error.
- 14 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (6) , 1802-1811
Characterization and Modeling of Commercial ICs for System-Efficient ESD Design
Optimizing electrostatic discharge (ESD) protection strategies requires simulation models of both on - and off -die ESD devices, but detailed information about on -die ESD protection is rarely available. Methods are proposed in the following paper to characterize and model the on -chip ESD protection using only measurements, with minimal a priori information about how the protection is implemented. The characterization targets a three-terminal (rather than the traditional two-terminal) protection structure, including the I/O, Vdd, Vss pins, and allows for current to flow between multiple pins simultaneously. A previously-developed behavioral model for TVS devices is used to capture the ESD behavior of the integrated circuit (IC), including its linear, quasi-static, and transient nonlinear response. The approach is used to model the equivalent current that flows through the on -chip ESD protection of two commercial ICs. The model of the on -chip ESD protection is combined with a behavioral model of an off -chip transient voltage suppressor to demonstrate their combined performance in a system-efficient ESD design (SEED) simulation. The model is validated both when the IC is powered- off and powered- on . The SEED model was able to predict quasistatic and peak voltages and currents at the IC with less than a 10% error.
- 7 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (4) , 907-914
Transient Response of ESD Protection Devices for a High-Speed I/O Interface
System-efficient electrostatic discharge (ESD) design (SEED) models of a diode and transient voltage suppressor (TVS) were developed to study their transient response in a high-speed input/output interface. Previously reported SEED models were improved to strengthen their convergence stability and facilitate accurate predictions over a wide range of conditions. These improvements were required to accurately capture the race conditions between the TVS and on -chip diode, where the diode's turn on may prevent turn on of the TVS. Simulations and measurements were performed to demonstrate the impact of the ESD pulse's rise time on race conditions. During a race, results showed the worst-case quasi-static diode current could be twice as high for long rise-time pulses than for short rise-times where the TVS does not turn on , and on -chip diode current may be larger at low test voltages than at high test voltages where the TVS does turn on . Adding a small passive impedance between the external TVS and the on -chip diode helps the TVS turn on and reduce the current through the on -chip diode by more than 50%. Similarly, lengthening the trace between the TVS and diode could reduce on -chip diode current by up to a factor of two.
- 7 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (4) , 907-914
Transient Response of ESD Protection Devices for a High-Speed I/O Interface
System-efficient electrostatic discharge (ESD) design (SEED) models of a diode and transient voltage suppressor (TVS) were developed to study their transient response in a high-speed input/output interface. Previously reported SEED models were improved to strengthen their convergence stability and facilitate accurate predictions over a wide range of conditions. These improvements were required to accurately capture the race conditions between the TVS and on -chip diode, where the diode's turn on may prevent turn on of the TVS. Simulations and measurements were performed to demonstrate the impact of the ESD pulse's rise time on race conditions. During a race, results showed the worst-case quasi-static diode current could be twice as high for long rise-time pulses than for short rise-times where the TVS does not turn on , and on -chip diode current may be larger at low test voltages than at high test voltages where the TVS does turn on . Adding a small passive impedance between the external TVS and the on -chip diode helps the TVS turn on and reduce the current through the on -chip diode by more than 50%. Similarly, lengthening the trace between the TVS and diode could reduce on -chip diode current by up to a factor of two.
- 26 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
A Hybrid Finite Difference Model for Snapback Devices with Lowly Doped Regions in SPICE
A hybrid finite difference model for SCRs and open base transistors with a lowly doped region is presented. It solves the diffusion and transport equation in a spice simulator. The results are compared with VF-TLP measurements for different rise times and different lengths of the lowly doped region of the devices. A good agreement of the simulated and measured quasi-static and peak voltage is achieved.
- 26 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
A Hybrid Finite Difference Model for Snapback Devices with Lowly Doped Regions in SPICE
A hybrid finite difference model for SCRs and open base transistors with a lowly doped region is presented. It solves the diffusion and transport equation in a spice simulator. The results are compared with VF-TLP measurements for different rise times and different lengths of the lowly doped region of the devices. A good agreement of the simulated and measured quasi-static and peak voltage is achieved.
- 5 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4214-4222
3-D TCAD Methodology for Simulating Double-Hysteresis Filamentary I–V Behavior and Holding Current in ESD Protection SCRs
Current filament (CF)-related double-hysteresis ${I}$ – ${V}$ behavior and holding current, ${I} _{\text {HOLD}}$ , are analyzed using experiments and 3-D technology computer-aided design (TCAD) simulation in silicon-controlled rectifiers (SCR) for system-level electrostatic discharge (ESD) protection. Our 3-D TCAD methodology uses up and down quasi-dc current sweeps to reveal a memory effect in the current density distribution along the device width. ${I} _{\text {HOLD}}$ is related to the smallest possible CF where the self-sustaining SCR action takes place during down current sweep. ${I} _{\text {HOLD}}$ exhibits a nontrivial dependence on device width, depending on whether a CF is created or not. Analyzing devices of different layouts shows that ${I} _{\text {HOLD}}$ values determined from experiments and 3-D TCAD are almost layout-independent and substantially lower than those evaluated from 2-D TCAD. ${I} _{\text {HOLD}}$ calculated by 3-D TCAD in edge-terminated devices is higher than that in 3-D structures obtained from simple width-extended 2-D doping profiles. The use of latter devices, thus, simplifies the 3-D TCAD ${I}$ – ${V}$ analysis and provides a safe margin for ${I} _{\text {HOLD}}$ prediction. The work is relevant for designing the latch-up immunity of ESD protection devices, and it also shows that conventional 2-D TCAD can provide unwanted overestimation of ${I} _{\text {HOLD}}$ .
- 5 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4214-4222
3-D TCAD Methodology for Simulating Double-Hysteresis Filamentary I–V Behavior and Holding Current in ESD Protection SCRs
Current filament (CF)-related double-hysteresis ${I}$ – ${V}$ behavior and holding current, ${I} _{\text {HOLD}}$ , are analyzed using experiments and 3-D technology computer-aided design (TCAD) simulation in silicon-controlled rectifiers (SCR) for system-level electrostatic discharge (ESD) protection. Our 3-D TCAD methodology uses up and down quasi-dc current sweeps to reveal a memory effect in the current density distribution along the device width. ${I} _{\text {HOLD}}$ is related to the smallest possible CF where the self-sustaining SCR action takes place during down current sweep. ${I} _{\text {HOLD}}$ exhibits a nontrivial dependence on device width, depending on whether a CF is created or not. Analyzing devices of different layouts shows that ${I} _{\text {HOLD}}$ values determined from experiments and 3-D TCAD are almost layout-independent and substantially lower than those evaluated from 2-D TCAD. ${I} _{\text {HOLD}}$ calculated by 3-D TCAD in edge-terminated devices is higher than that in 3-D structures obtained from simple width-extended 2-D doping profiles. The use of latter devices, thus, simplifies the 3-D TCAD ${I}$ – ${V}$ analysis and provides a safe margin for ${I} _{\text {HOLD}}$ prediction. The work is relevant for designing the latch-up immunity of ESD protection devices, and it also shows that conventional 2-D TCAD can provide unwanted overestimation of ${I} _{\text {HOLD}}$ .