Guido Notermans
Research Subjects
Research Interests
Guido Notermans has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Hans-Martin Ritter
Nexperia Germany GmbH, Hamburg, Germany
6 shared publications - Steffen Holland
Nexperia Germany GmbH, Hamburg, Germany
6 shared publications - David Pommerenke
Graz University of Technology
3 shared publications Burkhard Laue
NXP Semiconductors Germany GmbH, Hamburg, Germany
2 shared publications- Dionyz Pogany
Institute of Solid State Electronics, TU Wien (TU Vienna), Vienna, Austria
2 shared publications - Hasan Karaca
Institute of Solid State Electronics (FKE), Vienna University of Technology (TU Wien), Vienna, Austria
2 shared publications
Latest Publications
- 26 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
A Hybrid Finite Difference Model for Snapback Devices with Lowly Doped Regions in SPICE
A hybrid finite difference model for SCRs and open base transistors with a lowly doped region is presented. It solves the diffusion and transport equation in a spice simulator. The results are compared with VF-TLP measurements for different rise times and different lengths of the lowly doped region of the devices. A good agreement of the simulated and measured quasi-static and peak voltage is achieved.
- 26 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
A Hybrid Finite Difference Model for Snapback Devices with Lowly Doped Regions in SPICE
A hybrid finite difference model for SCRs and open base transistors with a lowly doped region is presented. It solves the diffusion and transport equation in a spice simulator. The results are compared with VF-TLP measurements for different rise times and different lengths of the lowly doped region of the devices. A good agreement of the simulated and measured quasi-static and peak voltage is achieved.
- 5 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4214-4222
3-D TCAD Methodology for Simulating Double-Hysteresis Filamentary I–V Behavior and Holding Current in ESD Protection SCRs
Current filament (CF)-related double-hysteresis ${I}$ – ${V}$ behavior and holding current, ${I} _{\text {HOLD}}$ , are analyzed using experiments and 3-D technology computer-aided design (TCAD) simulation in silicon-controlled rectifiers (SCR) for system-level electrostatic discharge (ESD) protection. Our 3-D TCAD methodology uses up and down quasi-dc current sweeps to reveal a memory effect in the current density distribution along the device width. ${I} _{\text {HOLD}}$ is related to the smallest possible CF where the self-sustaining SCR action takes place during down current sweep. ${I} _{\text {HOLD}}$ exhibits a nontrivial dependence on device width, depending on whether a CF is created or not. Analyzing devices of different layouts shows that ${I} _{\text {HOLD}}$ values determined from experiments and 3-D TCAD are almost layout-independent and substantially lower than those evaluated from 2-D TCAD. ${I} _{\text {HOLD}}$ calculated by 3-D TCAD in edge-terminated devices is higher than that in 3-D structures obtained from simple width-extended 2-D doping profiles. The use of latter devices, thus, simplifies the 3-D TCAD ${I}$ – ${V}$ analysis and provides a safe margin for ${I} _{\text {HOLD}}$ prediction. The work is relevant for designing the latch-up immunity of ESD protection devices, and it also shows that conventional 2-D TCAD can provide unwanted overestimation of ${I} _{\text {HOLD}}$ .
- 5 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4214-4222
3-D TCAD Methodology for Simulating Double-Hysteresis Filamentary I–V Behavior and Holding Current in ESD Protection SCRs
Current filament (CF)-related double-hysteresis ${I}$ – ${V}$ behavior and holding current, ${I} _{\text {HOLD}}$ , are analyzed using experiments and 3-D technology computer-aided design (TCAD) simulation in silicon-controlled rectifiers (SCR) for system-level electrostatic discharge (ESD) protection. Our 3-D TCAD methodology uses up and down quasi-dc current sweeps to reveal a memory effect in the current density distribution along the device width. ${I} _{\text {HOLD}}$ is related to the smallest possible CF where the self-sustaining SCR action takes place during down current sweep. ${I} _{\text {HOLD}}$ exhibits a nontrivial dependence on device width, depending on whether a CF is created or not. Analyzing devices of different layouts shows that ${I} _{\text {HOLD}}$ values determined from experiments and 3-D TCAD are almost layout-independent and substantially lower than those evaluated from 2-D TCAD. ${I} _{\text {HOLD}}$ calculated by 3-D TCAD in edge-terminated devices is higher than that in 3-D structures obtained from simple width-extended 2-D doping profiles. The use of latter devices, thus, simplifies the 3-D TCAD ${I}$ – ${V}$ analysis and provides a safe margin for ${I} _{\text {HOLD}}$ prediction. The work is relevant for designing the latch-up immunity of ESD protection devices, and it also shows that conventional 2-D TCAD can provide unwanted overestimation of ${I} _{\text {HOLD}}$ .
- 2 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 63 (6) , 1791-1798
Investigations Into Unintended ESD Generator Artifacts: Prepulse and Postpulse
An electrostatic discharge (ESD) generator may create pre- and postpulses in addition to the main pulse. These artifacts can cause additional device under test (DUT) failures. The origin and magnitude of these pulses were investigated in four commercial generators using measurements and simulation. Two types of unwanted pulses were identified. One is caused by the reignition of the spark, and the other relates to the relay contacting for charging the main capacitor. These pulses cause strong high-frequency signals, partially surpassing the radio frequency content of the main pulse. The spectrum of the pre- and postpulses varies greatly between different generators. These differences and the fact that some DUTs may react to the pre- or postpulse instead of the main pulse lead to repeatability problems between test sites. The other artifact that has been investigated is the leakage current in contact discharge mode. The charge accumulated on the gun tip by the leakage current can contribute to a short (few nanoseconds) fast-rising pulse (<500 ps) that occurs the moment the tip is contacted, thus, before the main pulse in contact mode.
- 2 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 63 (6) , 1791-1798
Investigations Into Unintended ESD Generator Artifacts: Prepulse and Postpulse
An electrostatic discharge (ESD) generator may create pre- and postpulses in addition to the main pulse. These artifacts can cause additional device under test (DUT) failures. The origin and magnitude of these pulses were investigated in four commercial generators using measurements and simulation. Two types of unwanted pulses were identified. One is caused by the reignition of the spark, and the other relates to the relay contacting for charging the main capacitor. These pulses cause strong high-frequency signals, partially surpassing the radio frequency content of the main pulse. The spectrum of the pre- and postpulses varies greatly between different generators. These differences and the fact that some DUTs may react to the pre- or postpulse instead of the main pulse lead to repeatability problems between test sites. The other artifact that has been investigated is the leakage current in contact discharge mode. The charge accumulated on the gun tip by the leakage current can contribute to a short (few nanoseconds) fast-rising pulse (<500 ps) that occurs the moment the tip is contacted, thus, before the main pulse in contact mode.
- 11 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (4) , 650-657
Transient Overshoot Voltages During VF-TLP Pulses for Bipolar Devices in the Presence of Lowly Doped Regions
The transient overshoot behavior of bipolar devices is investigated by means of very fast transmission line pulses (VF-TLP). All devices under investigation, a forward biased diode, an open base transistor and a SCR comprise a lowly doped region (LDR). Measurements have been done for rise times of 0.3ns and 1ns. To separate the voltage drop inside the device from parasitic contributions TCAD simulations have been performed. The analysis shows that for a fixed length of LDR the effect of the lowly doped region depends on the type of the device and is linked to the charge carrier distribution inside the LDR. In addition, the effect of the length of the LDR on transient voltage overshoot is compared for a forward biased diode and an SCR.
- 11 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (4) , 650-657
Transient Overshoot Voltages During VF-TLP Pulses for Bipolar Devices in the Presence of Lowly Doped Regions
The transient overshoot behavior of bipolar devices is investigated by means of very fast transmission line pulses (VF-TLP). All devices under investigation, a forward biased diode, an open base transistor and a SCR comprise a lowly doped region (LDR). Measurements have been done for rise times of 0.3ns and 1ns. To separate the voltage drop inside the device from parasitic contributions TCAD simulations have been performed. The analysis shows that for a fixed length of LDR the effect of the lowly doped region depends on the type of the device and is linked to the charge carrier distribution inside the LDR. In addition, the effect of the length of the LDR on transient voltage overshoot is compared for a forward biased diode and an SCR.
- 26 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (4) , 632-640
Simultaneous and Sequential Triggering in Multi-Finger Floating-Base SCRs Depending on TLP Pulse Rise Time
Multi-finger floating-base silicon controlled rectifiers (SCRs) of discrete technologies are investigated by transmission line pulses (TLP) with short (300ps) and long (10ns) pulse rise times (RT). Transient interferometric mapping (TIM) is applied to study the finger triggering dynamics. The measurements are correlated with TCAD simulation. It is found that for short RT the fingers trigger simultaneously which is due to the positive influence of a voltage overshoot related to delayed conductivity modulation. For long RT the fingers trigger sequentially which is accompanied by the voltage drops near the holding voltage. The time delay between the triggering of neighboring fingers is in the 3-150ns range and depends on the actual current density in fingers. The sequential finger triggering is due to lateral carrier diffusion-limited processes and the coupling via substrate currents.
- 26 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (4) , 632-640
Simultaneous and Sequential Triggering in Multi-Finger Floating-Base SCRs Depending on TLP Pulse Rise Time
Multi-finger floating-base silicon controlled rectifiers (SCRs) of discrete technologies are investigated by transmission line pulses (TLP) with short (300ps) and long (10ns) pulse rise times (RT). Transient interferometric mapping (TIM) is applied to study the finger triggering dynamics. The measurements are correlated with TCAD simulation. It is found that for short RT the fingers trigger simultaneously which is due to the positive influence of a voltage overshoot related to delayed conductivity modulation. For long RT the fingers trigger sequentially which is accompanied by the voltage drops near the holding voltage. The time delay between the triggering of neighboring fingers is in the 3-150ns range and depends on the actual current density in fingers. The sequential finger triggering is due to lateral carrier diffusion-limited processes and the coupling via substrate currents.
- 11 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 19 (4) , 583-590
Dynamic Voltage Overshoot During Triggering of an SCR-Type ESD Protection
- 11 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 19 (4) , 583-590
Dynamic Voltage Overshoot During Triggering of an SCR-Type ESD Protection
- 15 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 1 (1) , 9-13
Robustness of PIN Limiter Diodes to an ESD Event Based on VF-TLP Characterization
PIN limiter diodes are primarily used for protection from excess RF power in RF circuits. These diodes are positioned onboard at the I/O lines of the RF circuits. If an ESD event occurs, the first line of protection is offered by the PIN limiter diode. The main questions addressed in this letter are: Can the PIN limiter diode protect the RF circuit against ESD? If yes, then what is their ESD robustness? How do they compare against the standard ESD protection TVS diodes? This knowledge can guide the reader to understand whether or not the PIN limiter diode can help prevent ESD damage. The robustness of the diodes is investigated experimentally using a very fast transmission line pulse tester with a 10 ns pulse width and about 300-400 ps rise time. These diodes are tested for their withstand current, turn-on time at 1 A current, turn-on voltage, voltage clamp at 1 A current, capacitance, signal bandwidth, and effective package inductance. These diode parameters are essential in quantifying the component-level response of a device under test. This letter shows that the PIN limiter diodes are not a suitable replacement for the TVS diodes as an intentional ESD protection device. In case an ESD event occurs, these diodes are robust to ESD current levels up to 2.5-9 A and offer limited protection. They may effectively complement the TVS protection by offering a fast turn-on time and protection up to a certain ESD level, after which the (slower) TVS takes over.
- 15 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 1 (1) , 9-13
Robustness of PIN Limiter Diodes to an ESD Event Based on VF-TLP Characterization
PIN limiter diodes are primarily used for protection from excess RF power in RF circuits. These diodes are positioned onboard at the I/O lines of the RF circuits. If an ESD event occurs, the first line of protection is offered by the PIN limiter diode. The main questions addressed in this letter are: Can the PIN limiter diode protect the RF circuit against ESD? If yes, then what is their ESD robustness? How do they compare against the standard ESD protection TVS diodes? This knowledge can guide the reader to understand whether or not the PIN limiter diode can help prevent ESD damage. The robustness of the diodes is investigated experimentally using a very fast transmission line pulse tester with a 10 ns pulse width and about 300-400 ps rise time. These diodes are tested for their withstand current, turn-on time at 1 A current, turn-on voltage, voltage clamp at 1 A current, capacitance, signal bandwidth, and effective package inductance. These diode parameters are essential in quantifying the component-level response of a device under test. This letter shows that the PIN limiter diodes are not a suitable replacement for the TVS diodes as an intentional ESD protection device. In case an ESD event occurs, these diodes are robust to ESD current levels up to 2.5-9 A and offer limited protection. They may effectively complement the TVS protection by offering a fast turn-on time and protection up to a certain ESD level, after which the (slower) TVS takes over.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 16 (4) , 504-512
Design of an On-Board ESD Protection for USB3 Applications
This paper describes the development of an on-board system level protection for high-speed cable connections (e.g., USB3) with 15 kV robustness and a signal transfer rate of up to 10 Gb/s. A dedicated bipolar process is developed, on a high-resistive substrate with optimized diffusion profiles and a special via-on-via metallization to meet the capacitance target of 0.25 pF. The protection is shown to work well with several popular USB3 chipsets.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 16 (4) , 504-512
Design of an On-Board ESD Protection for USB3 Applications
This paper describes the development of an on-board system level protection for high-speed cable connections (e.g., USB3) with 15 kV robustness and a signal transfer rate of up to 10 Gb/s. A dedicated bipolar process is developed, on a high-resistive substrate with optimized diffusion profiles and a special via-on-via metallization to meet the capacitance target of 0.25 pF. The protection is shown to work well with several popular USB3 chipsets.
- 18 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Workshop and panel discussions: A.1 should the industry council address adequate IEC 6100-4-2 levels?
Industry Council on ESD target Levels has reached its 10th anniversary. During this decade the group of more than 60 experts representing IC suppliers, system OEMs, ODMs, ESD control consultants and foundries has published 5 White papers on recommended HBM and CDM targets, the clarification of misconceptions of system level ESD protection and the recommendation of system efficient ESD design (SEED). The most recent document published in 2016 addresses the problem of EOS failures and EOS prevention. All White Papers have been adopted and endorsed both by ESDA and JEDEC.
- 18 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Workshop and panel discussions: A.1 should the industry council address adequate IEC 6100-4-2 levels?
Industry Council on ESD target Levels has reached its 10th anniversary. During this decade the group of more than 60 experts representing IC suppliers, system OEMs, ODMs, ESD control consultants and foundries has published 5 White papers on recommended HBM and CDM targets, the clarification of misconceptions of system level ESD protection and the recommendation of system efficient ESD design (SEED). The most recent document published in 2016 addresses the problem of EOS failures and EOS prevention. All White Papers have been adopted and endorsed both by ESDA and JEDEC.
- 18 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Gun tests of a USB3 host controller board
System level tests on a USB3 controller with on-board protection were found to yield irreproducible failure levels. A root cause analysis was performed using a combination of gun tests, TLP tests, and SEED simulation. It was found that an inductive current distribution between protection and SoC may explain the actual failure levels. Solutions are presented for effective on-board protection of USB3 controller boards. In addition, several gun artifacts were identified which prevent reproducible failure levels when using gun discharges. Instead, 50 Ω HMM testing yields results which correlate very well with SEED simulations.
- 18 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Gun tests of a USB3 host controller board
System level tests on a USB3 controller with on-board protection were found to yield irreproducible failure levels. A root cause analysis was performed using a combination of gun tests, TLP tests, and SEED simulation. It was found that an inductive current distribution between protection and SoC may explain the actual failure levels. Solutions are presented for effective on-board protection of USB3 controller boards. In addition, several gun artifacts were identified which prevent reproducible failure levels when using gun discharges. Instead, 50 Ω HMM testing yields results which correlate very well with SEED simulations.