Gabriele Gazzaniga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gabriele Gazzaniga has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Denny Coffetti
University of Bergamo
3 shared publications - Elena Crotti
Department of Engineering and Applied Sciences, University of Bergamo, 24044 Dalmine (BG), Italy
3 shared publications - Luigi Coppola
University of Bergamo
3 shared publications - Tommaso Pastore
University of Bergamo, BERGAMO, Italy
3 shared publications Alberto Pavan
Politecnico di Milano
1 shared publicationBruno Daniotti
Politecnico di Milano
1 shared publication
Latest Publications
- Open Access
- 27 April 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (9) , 3561
The Durability of One-Part Alkali-Activated Slag-Based Mortars in Different Environments
The paper assesses the durability of one-part alkali-activated slag-based mortars (AAS) in different aggressive environments, such as calcium chloride- and magnesium sulphate-rich solutions, in comparison with traditional cementitious mortars at equal water to binder ratio. Moreover, the freezing and thawing resistance was evaluated on mortars manufactured with and without air entraining admixture (AEA). Experimental results indicate that the alkali content is a key parameter for durability of AAS: the higher the alkali content, the higher the resistance in severe conditions. In particular, high-alkali content AAS mortars are characterized by freeze–thaw resistances similar to that of blast furnace cement-based mixtures, but lower than that of Portland cement-mortars while AAS with low activators dosages evidence a very limited resistance in cold environment. The effectiveness of AEA in enhancement of freeze–thaw resistance is confirmed also for AAS mortars. Moreover, AAS mixtures are quasi-immune to expansive calcium oxychloride formation in presence of CaCl2-based deicing salts, but they are very vulnerable to magnesium sulphate attack due to decalcification of C-S-H gel and gypsum formation.
- 27 April 2020
- Published by MDPI AG in Sustainability
- Vol. 12 (9) , 3561
Open AccessThe Durability of One-Part Alkali-Activated Slag-Based Mortars in Different Environments
The paper assesses the durability of one-part alkali-activated slag-based mortars (AAS) in different aggressive environments, such as calcium chloride- and magnesium sulphate-rich solutions, in comparison with traditional cementitious mortars at equal water to binder ratio. Moreover, the freezing and thawing resistance was evaluated on mortars manufactured with and without air entraining admixture (AEA). Experimental results indicate that the alkali content is a key parameter for durability of AAS: the higher the alkali content, the higher the resistance in severe conditions. In particular, high-alkali content AAS mortars are characterized by freeze–thaw resistances similar to that of blast furnace cement-based mixtures, but lower than that of Portland cement-mortars while AAS with low activators dosages evidence a very limited resistance in cold environment. The effectiveness of AEA in enhancement of freeze–thaw resistance is confirmed also for AAS mortars. Moreover, AAS mixtures are quasi-immune to expansive calcium oxychloride formation in presence of CaCl2-based deicing salts, but they are very vulnerable to magnesium sulphate attack due to decalcification of C-S-H gel and gypsum formation.
- Open Access
Chloride Diffusion in Concrete Protected with a Silane-Based Corrosion Inhibitor
One of the most important parameters concerning durability is undoubtedly represented by cement matrix resistance to chloride diffusion in environments where reinforced concrete structures are exposed to the corrosion risk induced by marine environment or de-icing salts. This paper deals with protection from chloride ingress by a silane-based surface-applied corrosion inhibitor. Results indicated that the corrosion inhibitor (CI) allows to reduce the penetration of chloride significantly compared to untreated specimens, independently of w/c, cement type, and dosage. Reduction of chloride diffusion coefficient (Dnssn) measured by an accelerated test in treated concrete was in the range 30–60%. Natural chloride diffusion test values indicate a sharp decrease in apparent diffusion coefficient (Dapp) equal to about 75% when concrete is protected by CI. Mechanism of action of CI in slowing down the chloride penetration inside the cement matrix is basically due to the water repellent effect as confirmed by data of concrete bulk electrical resistivity.
Open AccessChloride Diffusion in Concrete Protected with a Silane-Based Corrosion Inhibitor
One of the most important parameters concerning durability is undoubtedly represented by cement matrix resistance to chloride diffusion in environments where reinforced concrete structures are exposed to the corrosion risk induced by marine environment or de-icing salts. This paper deals with protection from chloride ingress by a silane-based surface-applied corrosion inhibitor. Results indicated that the corrosion inhibitor (CI) allows to reduce the penetration of chloride significantly compared to untreated specimens, independently of w/c, cement type, and dosage. Reduction of chloride diffusion coefficient (Dnssn) measured by an accelerated test in treated concrete was in the range 30–60%. Natural chloride diffusion test values indicate a sharp decrease in apparent diffusion coefficient (Dapp) equal to about 75% when concrete is protected by CI. Mechanism of action of CI in slowing down the chloride penetration inside the cement matrix is basically due to the water repellent effect as confirmed by data of concrete bulk electrical resistivity.
- Open Access
- 31 December 2019
- Published by Springer Nature
- p. 61-71
Decision-Making BIM Platform for Chemical Building Products
- 31 December 2019
- Published by Springer Nature
- p. 61-71
Open AccessDecision-Making BIM Platform for Chemical Building Products
- Open Access
- 25 December 2019
- Published by MDPI AG in Applied Sciences
- Vol. 10 (1) , 176
Influence of Lithium Carbonate and Sodium Carbonate on Physical and Elastic Properties and on Carbonation Resistance of Calcium Sulphoaluminate-Based Mortars
In this study, three different hardening accelerating admixtures (sodium carbonate, lithium carbonate and a blend of sodium and lithium carbonates) were employed to prepare calcium sulphoaluminate cement-based mortars. The workability, setting times, entrapped air, elasto-mechanical properties such as compressive strength and dynamic modulus of elasticity, free shrinkage, water absorption and carbonation rate were measured and mercury intrusion porosimetry were also performed. Experimental results show that a mixture of lithium carbonate and sodium carbonate acts as a hardening accelerating admixture, improving the early-age strength and promoting a remarkable pore structure refinement. Finally, sodium carbonate also reduces the water absorption, the carbonation rate and the shrinkage of mortars without affecting the setting times and the workability.
- 25 December 2019
- Published by MDPI AG in Applied Sciences
- Vol. 10 (1) , 176
Open AccessInfluence of Lithium Carbonate and Sodium Carbonate on Physical and Elastic Properties and on Carbonation Resistance of Calcium Sulphoaluminate-Based Mortars
In this study, three different hardening accelerating admixtures (sodium carbonate, lithium carbonate and a blend of sodium and lithium carbonates) were employed to prepare calcium sulphoaluminate cement-based mortars. The workability, setting times, entrapped air, elasto-mechanical properties such as compressive strength and dynamic modulus of elasticity, free shrinkage, water absorption and carbonation rate were measured and mercury intrusion porosimetry were also performed. Experimental results show that a mixture of lithium carbonate and sodium carbonate acts as a hardening accelerating admixture, improving the early-age strength and promoting a remarkable pore structure refinement. Finally, sodium carbonate also reduces the water absorption, the carbonation rate and the shrinkage of mortars without affecting the setting times and the workability.