JJJae-Hyung Jung

Jae-Hyung Jung

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jae-Hyung Jung has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Highly Reliable SIMO Converter Using Hybrid Starter and Overcharging Protector for Energy Harvesting Systems

    by Jae-Hyung Jung, Seong-Kwan Hong, Oh-Kyong Kwon

    This paper proposes a highly reliable single-inductor multi-output (SIMO) converter for energy harvesting systems, which is controlled by the power management controller (PMC) including the hybrid starter, overcharging protector (OCP), and switch controller (SWC). The proposed hybrid starter employs the power-on-reset to accurately control the activated and deactivated moments of the SWC, thus generating a system supply voltage (VSYS) within the stable operating voltage range. The proposed OCP employs the diode-connection and Schmitt trigger schemes to monitor the voltage of a storage device (VSTG) in real time, thereby protecting the IC from being damaged without using either a capacitor or Zener diode, which causes the additional area or reverse leakage current, respectively. The proposed SIMO converter with the PMC was fabricated using 0.18-μm CMOS process. The measurement results show that VSYS values at the activated and deactivated moments of the SWC are 1.798 V and 1.510 V, respectively, both of which are within the stable system voltage range for 1.8 V devices. In addition, the measured maximum VSTG is 5.892 V, which is much lower than an absolute maximum rated voltage of 9.2 V for 5 V devices. Furthermore, the measurement results reveal that the hybrid starter allows the proposed SIMO converter to be properly restarted immediately after VSYS is shorted to ground, while the OCP safely protects the SIMO converter even when the storage device is removed from the IC while charging. Therefore, the proposed SIMO converter with the PMC is suitable for energy harvesting systems that require high reliability.


  • A Fast Transient Response Hybrid LDO With Highly Accurate DC Voltage Using Countable Bidirectional Binary Search and Soft Swap Switching

    by Jae-Hyung Jung, Seong-Kwan Hong, Oh-Kyong Kwon

    This paper proposes a fast transient response hybrid low dropout (LDO) regulator with highly accurate DC voltage for system-on-chip (SoC) applications. The proposed hybrid LDO, which consists of the analog and digital LDOs (ALDO and DLDO), and a hybrid controller, employs a hybrid algorithm in the hybrid controller to control the ALDO and DLDO so as to produce its accurately regulated output voltage. The proposed hybrid algorithm is realized with the countable bidirectional binary search (CBBS) and soft swap switching (SSS) through logic synthesis. The CBBS quickly determines the coarse-tuning current of the DLDO by controlling the number of turned-on switches in the DLDO, resulting in a fast transient response. In addition, the SSS precisely adjusts the fine-tuning current of the ALDO by controlling the moment when the ALDO is activated, resulting in a highly accurate DC voltage. The proposed hybrid LDO was fabricated using a 0.18-μm standard CMOS process technology. The measurement results show that the output of the hybrid LDO is regulated at 0.9 V when the input voltage ranges from 1.2 V to 1.8 V. In addition, the measured undershoot and overshoot voltages are 34 mV and 56 mV with the settling times of 68 ns and 344 ns, respectively, at a load current step of about 40 mA. Therefore, the proposed hybrid LDO is suitable for SoC applications requiring fast transient response and highly accurate DC voltage.


  • A High Peak Output Power and High Power Conversion Efficiency SIMIMO Converter Using Optimal on-Time Control and Hybrid Zero Current Switching for Energy Harvesting Systems in IoT Applications

    by Jae-Hyung Jung, Young-Ho Jung, Seong-Kwan Hong, Oh-Kyong Kwon

    This paper proposes a single inductor multi-input multi-output (SIMIMO) converter with high peak output power and power conversion efficiency for energy harvesting systems in Internet of Things (IoT) applications. The proposed SIMIMO converter consists of inputs with four harvesters and a battery, and outputs with 1.8 V output, 3.3 V output, and a battery. The optimal on-time control method is proposed to optimally adjust the on-time required to energize the inductor, thus increasing the peak output power to cover a wide distance range. In addition, the hybrid zero current switching method is proposed to adaptively calibrate the offset of the ZCS comparator, thus improving the power conversion efficiency. The proposed SIMIMO converter was fabricated using 0.18-μm standard BCD process technology with 1.8 V and 5 V devices. The measurement results show that the peak output power is achieved to be 462 mW, and the peak power conversion efficiencies at 1.8 V output, 3.3 V output, and battery are 89.2%, 84.5%, and 86.4%, respectively. Moreover, the quiescent current of the power management controller, which controls the proposed converter, is achieved to be only 1.6 μA. Therefore, the proposed SIMIMO converter is suitable for energy harvesting systems in various IoT applications.


  • A Fast and Highly Accurate Battery Charger With Accurate Built-In Resistance Detection

    by Young-Ho Jung, Jae-Hyung Jung, Hoe-Eung Jeong, Jae-Sung An, Hyun-A. Ahn, Seong-Kwan Hong, Oh-Kyong Kwon

    This letter proposes a fast and highly-accurate battery charger for mobile applications. The proposed battery charger accurately detects the built-in resistance (BIR) and determines the transition point from the constant current (CC) to constant voltage (CV) modes. It then maximizes and minimizes the durations of the CC and CV modes, respectively, thus reducing the battery charging time. In addition, the proposed charger accurately controls the charging current (IBAT) by employing an adaptive off-time-controlled switching charger. The proposed battery charger was fabricated using a 0.18-μm standard CMOS process. The measurement results showed that with the use of the accurate BIR detection and adaptive off-time-control methods, the proposed charger reduced the total charging time by up to 41.2%, and achieved IBAT ripple of 52 mAp-p.