Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hesam Moghadasi has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A CFD assessment of Weber number impacts on dropwise condensation heat transfer for an individual droplet

    by Loghman Mohammadpour, Hesam Moghadasi

    Due to the high importance of Dropwise Condensation (DWC) in industry fields, it has attracted significant attention to itself during the last decades. Numerous researchers have been doing much effort to study the ways that may contribute to an amelioration in heat transfer rate in DWC. In this assessment, a computational fluid dynamics (CFD) analysis executed to assess the influence of the Weber number ([Formula: see text]) on the heat transfer between a liquid droplet and a flat solid surface. In this regard, to simulate the droplet's morphology, Surface Evolver (SE) was employed, and governing equations were processed through the use of the finite volume method (FVM) as well. Additionally, ANSYS FLUENT, a CFD solver, was utilized to calculate the average heat flux for diverse [Formula: see text] numbers, incorporating the influence of critical parameters such as saturation temperature, droplet size, and fluid properties. The results were also validated against available data and it showed acceptable agreement. The findings of this study demonstrate that increasing the [Formula: see text] number from 0.1 to 0.4 for a water droplet with a volume of 2 [Formula: see text] and a contact angle of [Formula: see text] leads to a 38.43% enhancement in average heat flux, indicating a significant improvement in thermal performance.

  • Open Access

    Assessing parameters impact in dropwise condensation heat transfer for an individual droplet on inclined/grooved surfaces: a sobol sensitivity analysis

    by Mehran Afshari, Hesam Moghadasi, Loghman Mohammadpour

    Dropwise condensation (DWC) heat transfer models, at the level of individual liquid droplets, supply insights on a scientific basis for improving condensation processes. Therefore, heat transfer rates and parameters controlling these should be measured correctly. This investigation examined four distinct scenarios to assess parameter sensitivities. The analysis quantified the relative contributions of key variables to average heat flux and temperature distribution using Sobol’s sensitivity indices, specifically evaluating inclination angles, roughness index, contact angle, Nusselt (\(\:Nu\)) number, droplet height, and saturation temperatures. The study employed Design-Expert software to execute Response Surface Methodology (RSM), utilizing its regression approach and analysis of variance (ANOVA) capabilities to statistically validate the developed models and their constituent terms. Also, the sensitivity analysis was carried out employing the UQLab computational framework, which provides advanced capabilities for uncertainty quantification and global sensitivity analysis. Moreover, Sobol indices were computed utilizing two estimators with 95% confidence intervals from 1000 bootstrap resamples. Sensitivity analysis demonstrates that in general, the DWC heat transfer model is fairly highly sensitive to saturation temperature,\(\:\:Nu\) number, and inclination angle. Furthermore, for rough surfaces, contact angle and saturation temperature dominate the impact on model predictions. Besides, the average heat flux and temperature distribution demonstrate significantly higher sensitivity to the \(\:Nu\) number and saturation temperature, respectively compared to the other input parameters as evidenced by Sobol’ sensitivity indices. Based on the outcomes, employing Janon estimator the maximum total effect Sobol’ indices for scenarios of 1 and 4 are 99.22% and 92.7%, respectively. Such information is crucial in guiding the effort toward parameter accuracy in experimental characterization and computational modeling of DWC mechanisms.


  • Open Access

    Assessing Parameters Impact in Dropwise Condensation Heat Transfer for an Individual Droplet on Inclined/Grooved Surfaces: A Sobol Sensitivity Analysis

    by Mehran Afshari, Hesam Moghadasi, Loghman Mohammadpour

    Dropwise condensation (DWC) heat transfer models, at the level of individual liquid droplets, supply insights on a scientific basis for improving condensation processes. Therefore, heat transfer rates and parameters controlling these should be measured correctly. This investigation examined four distinct scenarios to assess parameter sensitivities. The analysis quantified the relative contributions of key variables to average heat flux and temperature distribution using Sobol's sensitivity indices, specifically evaluating inclination angles, roughness index, contact angle, Nusselt (\(\:Nu\)) number, droplet height, and saturation temperatures. The study employed Design-Expert software to execute Response Surface Methodology (RSM), utilizing its regression approach and analysis of variance (ANOVA) capabilities to statistically validate the developed models and their constituent terms. Also, the sensitivity analysis was carried out employing the UQLab computational framework, which provides advanced capabilities for uncertainty quantification and global sensitivity analysis. Moreover, sensitivity analysis demonstrates that in general, the DWC heat transfer model is fairly highly sensitive to saturation temperature,\(\:\:Nu\) number, and inclination angle. Furthermore, for rough surfaces, contact angle and saturation temperature dominate the impact on model predictions. Besides, the average heat flux and temperature distribution demonstrate significantly higher sensitivity to the \(\:Nu\) number and saturation temperature, respectively compared to the other input parameters as evidenced by Sobol' sensitivity indices. Based on the outcomes, the maximum normalized total effect Sobol’ indices for scenarios of 1 and 4 are 99.24% and 93.05%, respectively. Such information is crucial in guiding the effort toward parameter accuracy in experimental characterization and computational modeling of DWC mechanisms.

  • Open Access

    The influence of Nusselt number on dropwise condensation heat transfer for a single droplet on inclined and grooved surfaces

    by Loghman Mohammadpour, Hesam Moghadasi, Ali Moosavi

    Dropwise condensation (DWC) is a widely studied vapor–liquid phase-change process that has attracted significant research attention due to its exceptional energy transfer efficiency. Therefore, it is highly important to predict the heat transfer rate during DWC and the factors that affect it. This study presents a computational fluid dynamics (CFD) investigation on DWC heat transfer under diverse circumstances for a single droplet on inclined and rough surfaces with Wenzel structure. Drop’s shape simulation was done utilizing the Surface Evolver (SE) software and the governing equations were solved based on the finite volume method. Moreover, for different Nusselt numbers (\(Nu\)), the average heat flux was calculated by considering the effect of different inclination angles, contact angles, and saturation temperatures. Validation was performed by comparing the outcomes with the available data in the literature, and a satisfactory agreement was achieved. The study revealed that the average heat flux for a water droplet with the saturation temperature \({T}_{sat}\) = 313 K on an inclined surface with an inclination angle of β = 90° increases by 151.79% when the Nu is increased from 510 to 740. Similarly, for a droplet on a rough surface with a roughness index of \({r}_{i}\) = 0.6, the increase in heat flux is 152%. Moreover, an increase in saturation temperature results in a higher heat flux for both inclined and rough surfaces. The augmentation follows a specific trend for each of the surfaces.


  • Open Access

    Computational Fluid Dynamics Modeling of Top-Down Digital Light Processing Additive Manufacturing

    by Hesam Moghadasi, Tusher Mollah, Deepak Marla, Hamid Saffari, Jon Spangenberg

    Digital light processing (DLP) as a vat photopolymerization technique is one of the most popular three-dimensional (3D) printing methods, where chains are formed between liquid photocurable resin molecules to crosslink them and solidify the liquid resin using ultraviolet light. The DLP technique is inherently complex and the part accuracy depends on the process parameters that have to be chosen based on the fluid (resin) properties. In the present work, computational fluid dynamics (CFD) simulations are presented for top-down DLP as photocuring 3D printing. The effects of fluid viscosity, travelling speed of build part, travelling speed ratio (ratio of the up-to-down traveling speeds of build part), printed layer thickness, and travel distance considering 13 various cases are scrutinized by the developed model to obtain a stability time of fluid interface. The stability time describes the time it takes for the fluid interface to show minimum fluctuations. According to the simulations, a higher viscosity leads to prints with higher stability time. However, lower stability times in the printed layers are caused by a higher traveling speed ratio (TSR). The variation in settling times with TSR is extremely small in comparison to that of viscosity and travelling speed variations. As a result, a declining trend can be detected for the stability time by increasing the printed layer thickness, while by enhancing the travel distance values, the stability time demonstrated a descending pattern. In total, it was revealed that it is essential to choose optimal process parameters for achieving practical results. Moreover, the numerical model can assist in the optimizing the process parameters.


  • Open Access

    A Computational Fluid Dynamics Study of Laminar Forced Convection Improvement of a Non-Newtonian Hybrid Nanofluid within an Annular Pipe in Porous Media

    by Hesam Moghadasi, Mohamad Bayat, Ehsan Aminian, Jesper H. Hattel, Mahdi Bodaghi

    Porous inserts and nanofluids are among the conventional methods for the amelioration of heat transfer in industrial systems. The heat transfer rate could also be improved by utilizing porous substances with a higher thermal conductivity in these systems. This research work presents a two-dimensional (2D) numerical examination of the laminar forced convection of an Al2O3-CuO-carboxy methyl cellulose (CMC) non-Newtonian hybrid nanofluid within an annular pipe in a porous medium. The porous medium was inserted within two inner or outer wall cases. For hybrid nanofluid flow modeling in porous media, a Darcy–Brinkman–Forchheimer formulation was employed. Additionally, a power-law technique was utilized as a fluid viscosity model for the considered non-Newtonian fluid. The governing equations were discretized according to the finite volume method (FVM) using the computational fluid dynamics (CFD) software package ANSYS-FLUENT. The cylinder walls’ thermal boundary conditions were exposed to a constant heat flux. For various Darcy numbers, the impacts of different volume fractions of the hybrid nanofluid (0% to 5%), the total Nusselt number, the pressure drop, and the performance number (PN) were evaluated. The outcomes indicate that the heat transfer coefficient increases considerably with a decrease in the Darcy number (0.1 to 0.0001), as well as with an increase in the porous thickness ratio. Moreover, it was found that the nanoparticles’ increased volume fraction would ameliorate the heat transfer and, more considerably, the PN factor. Furthermore, according to the outcomes in both cases I and II for a constant porous thickness ratio and Darcy number (rp=1,Da=0.0001) and a high volume fraction (φ=5%), the maximum total Nusselt number reached 1274.44. Moreover, applying a volume fraction of 5% with Da=0.1 and rp=1 reached the highest value of the PN index equal to 7.61, which is augmented as roughly 88% compared to the case of a zero volume fraction.


  • Transient analysis of convective-radiative heat transfer through porous fins with temperature-dependent thermal conductivity and internal heat generation

    by Armin Emamifar, Hesam Moghadasi, Mohammad Javad Noroozi, Hamid Saffari

    In this research study, the transient study of heat transfer through a convective-radiative porous fin is carried out considering temperature-dependent thermal conductivity and internal heat generation. The unsteady Galerkin weighted residuals technique is employed to obtain the transient temperatures of the porous fin. The results indicate that increasing of the fin base temperature, internal heat generation and, thermal conductivity lead to increase heat transfer along the fin and consequently the higher temperature of the entire of the fin achieved. However, increasing of the porous and radiative parameters result in more heat dissipation from the fin and cause to lowering the fin temperature which leads to increase heat flux entering the fin through the base. Furthermore, the transient thermal analysis of the porous fin illustrates that by increasing the porous and the radiation parameters, the fin cools down faster, so in the applications that the time of cooling is more important, these parameters can be more noticeable.


  • Numerical scrutinization of dropwise condensation heat transfer on an inclined surface

    by Loghman Mohammadpour, Hesam Moghadasi, Hamid Saffari

    Recently, achieving an ameliorated heat transfer rate in dropwise condensation (DWC) has attracted the attention of many researchers. Several parameters, including chemical and physical properties of the substrate, inclination, and interfacial characteristics influence DWC heat transfer rate. The variation of inclination angle is followed by the change in droplet shape and consequently, the heat transfer rate are changed. In this study, the effect of droplet shape variation on diverse inclined substrates is simulated. Moreover, three‐dimensional mass, momentum, and energy equations considering the desired boundary conditions on the unstructured grid are utilized for the scrutinization of flow behavior and heat transfer for static and sliding droplets. For the sake of validation, the outcomes obtained from the simulation were compared with existent data in the literature and a proper agreement was attained. Regarding the outcomes, it was of concern that the influence of inclination angle on the droplet shape is more distinct at higher droplet volume; while no considerable change was seen on heat flux of small droplets by increasing the inclination angle. Furthermore, a higher heat transfer rate was noted by exceeding the inclination angle beyond a definite angle. Additionally, the increased heat transfer rate was affirmed by increasing the Marangoni number .