Khushmeet Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Khushmeet Kumar has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Sushant Samir
8 shared publications- Sashank Thapa
Faculty of Engineering and Technology, Shoolini University, Solan 173229, India
4 shared publications - Raj Kumar
Department of Mechanical Engineering, Gachon University, Seongnam, South Korea
3 shared publications Sushma Singh
Punjab Engineering College
3 shared publicationsDeoraj Prajapati
2 shared publicationsSashank Thapa
Department of Mechanical Engineering, Punjab Engineering College (Deemed to be University), Chandigarh UT, India
2 shared publications
Latest Publications
- Open Access
- 20 November 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 76
Impact of roughness parameters on heat transfer and fluid flow behaviour of solar thermal air collector: CFD-based analysis
- 20 November 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 76
Open AccessImpact of roughness parameters on heat transfer and fluid flow behaviour of solar thermal air collector: CFD-based analysis
- Open Access
Solar Thermal Collector Roughened with S-Shaped Ribs: Parametric Optimization Using AHP-MABAC Technique
The current examination used a multi-criteria decision-making (MCDM) approach to optimize the roughness parameters of S-shaped ribs (SSRs) in a solar thermal collector (STC) duct using air as the working fluid. Different SSRs were tested to identify the combination of parameters resulting in the best performance. Geometrical parameters such as relative roughness pitch () varied from 4 to 12, relative roughness height () from 0.022 to 0.054, arc angle () from 30° to 75°, and relative roughness width () from 1 to 4. The Nusselt number () and friction factor (), findings which impact the STC performance, rely on SSRs. The performance measurements show that no combination of SSR parameters lead to the best enhancement heat transfer rate at low enhancement in the friction. So, a hybrid multi-criteria decision-making strategy using the Analytical Hierarchy Process (AHP) for criterion significance and Multi Attributive Border Approximation Area Comparison (MABAC) for alternative ranking was used to determine which combination of geometrical parameters will result in the optimum performance of a roughened STC. This work employs a hybrid MCDM technique to optimise the effectiveness of an STC roughened with SSRs. To optimize the SSR design parameters, this study used the hybrid AHP-MABAC technique for analytical assessment of a roughened STC. The optimization results showed that the STC roughened with SSRs achieved the optimum performance at = 8, = 0.043, = 60° and = 3.Open AccessSolar Thermal Collector Roughened with S-Shaped Ribs: Parametric Optimization Using AHP-MABAC Technique
The current examination used a multi-criteria decision-making (MCDM) approach to optimize the roughness parameters of S-shaped ribs (SSRs) in a solar thermal collector (STC) duct using air as the working fluid. Different SSRs were tested to identify the combination of parameters resulting in the best performance. Geometrical parameters such as relative roughness pitch () varied from 4 to 12, relative roughness height () from 0.022 to 0.054, arc angle () from 30° to 75°, and relative roughness width () from 1 to 4. The Nusselt number () and friction factor (), findings which impact the STC performance, rely on SSRs. The performance measurements show that no combination of SSR parameters lead to the best enhancement heat transfer rate at low enhancement in the friction. So, a hybrid multi-criteria decision-making strategy using the Analytical Hierarchy Process (AHP) for criterion significance and Multi Attributive Border Approximation Area Comparison (MABAC) for alternative ranking was used to determine which combination of geometrical parameters will result in the optimum performance of a roughened STC. This work employs a hybrid MCDM technique to optimise the effectiveness of an STC roughened with SSRs. To optimize the SSR design parameters, this study used the hybrid AHP-MABAC technique for analytical assessment of a roughened STC. The optimization results showed that the STC roughened with SSRs achieved the optimum performance at = 8, = 0.043, = 60° and = 3. - 2 January 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 239 (6) , 3337-3349
Performance analysis of solar parabolic trough receiver with twisted perforated conical inserts
A solar parabolic trough is one of the types of solar thermal collector used to harness sunlight and convert it into usable heat energy. Solar parabolic trough collector demonstrates reduced efficiency compared to point-focusing types of concentrating solar collectors when it comes to converting solar energy into thermal energy. This disparity arises due to its operation within the medium temperature range of 100–400 °C. The enhancement of efficiency is achievable through the utilization of several passive heat transfer augmentation methods within the receiver tube. Among these approaches, the implementation of conical strip inserts stands out as a particularly promising method in the receiver's design because of their straight-forward construction, simple design and wide range of geometric customization options. The present study examines how the solar parabolic trough receiver performs when passive heat augmentation approaches are used in the receiver. The evaluation involved testing using perforated conical strips with pitch ratios ( P *) of 0.5, 1.0, 1.5, 2.0, twist angle ( φ ) of 6°, 8°, 10°, 12°, and geometry angle ( θ ) as 60°, 70°, 80°, and 90° for Reynolds number ( Re ) in the range of 3000–21,000. Air is used as working fluid inside the solar parabolic trough receiver tube. The results demonstrate that modified receiver tube geometry significantly enhances the Nusselt number ( Nu ) and friction factor ( ff ) by 4.26 and 7.29 times as compared to the plain receiver tube respectively. This indicates an improvement in heat transfer characteristics of solar parabolic trough collector in term of thermo-hydraulic performance ( η T H ( T P C S ) ). The maximum ( η T H ( T P C S ) ) of 2.94 is received by using twisted perforated conical strips at pitch ratio ( P *) = 1, twist angle ( φ ) = 6° and geometry angle ( θ ) = 60° at the Re = 21,000. Correlations for Nu and ff of twisted perforated conical strips have also been established, demonstrating accuracy within the range of ±5.0% for Nu and ±4.5% for ff .
- 2 January 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 239 (6) , 3337-3349
Performance analysis of solar parabolic trough receiver with twisted perforated conical inserts
A solar parabolic trough is one of the types of solar thermal collector used to harness sunlight and convert it into usable heat energy. Solar parabolic trough collector demonstrates reduced efficiency compared to point-focusing types of concentrating solar collectors when it comes to converting solar energy into thermal energy. This disparity arises due to its operation within the medium temperature range of 100–400 °C. The enhancement of efficiency is achievable through the utilization of several passive heat transfer augmentation methods within the receiver tube. Among these approaches, the implementation of conical strip inserts stands out as a particularly promising method in the receiver's design because of their straight-forward construction, simple design and wide range of geometric customization options. The present study examines how the solar parabolic trough receiver performs when passive heat augmentation approaches are used in the receiver. The evaluation involved testing using perforated conical strips with pitch ratios ( P *) of 0.5, 1.0, 1.5, 2.0, twist angle ( φ ) of 6°, 8°, 10°, 12°, and geometry angle ( θ ) as 60°, 70°, 80°, and 90° for Reynolds number ( Re ) in the range of 3000–21,000. Air is used as working fluid inside the solar parabolic trough receiver tube. The results demonstrate that modified receiver tube geometry significantly enhances the Nusselt number ( Nu ) and friction factor ( ff ) by 4.26 and 7.29 times as compared to the plain receiver tube respectively. This indicates an improvement in heat transfer characteristics of solar parabolic trough collector in term of thermo-hydraulic performance ( η T H ( T P C S ) ). The maximum ( η T H ( T P C S ) ) of 2.94 is received by using twisted perforated conical strips at pitch ratio ( P *) = 1, twist angle ( φ ) = 6° and geometry angle ( θ ) = 60° at the Re = 21,000. Correlations for Nu and ff of twisted perforated conical strips have also been established, demonstrating accuracy within the range of ±5.0% for Nu and ±4.5% for ff .
- 1 March 2023
- Published by Bentham Science Publishers Ltd. in Recent Advances in Electrical & Electronic Engineering (Formerly Recent Patents on Electrical & Electronic Engineering)
- Vol. 16 (2) , 159-167
Detailed Study on Electronic Data Energy Consumption Monitoring System Based on the Construction of Internet of Things
Aim: To propose a set of dynamic model generation algorithm DPGA, the algorithm can generate parameter models and service models based on user scenarios. Background: Buildings in the traditional sense have become increasingly unable to meet modern humans’ pursuit of high-quality living and working environments, with the pace of urban development, modern buildings have gradually entered people's lives. Objective: Research on Electronic Data Energy Consumption Monitoring System Based on the Construction of Internet of Things. Method: The author made two definitions of the communication format between the middleware and the wireless sensor network, the author has designed the software and hardware functions of the nodes of the system's wireless sensor network, the author implements part of the node. Finally, the author describes the specific implementation of the application program interface and data interface between the modules of the middleware system, and take the internal environment of a typical office building as an example, the author discussed the deployment plan of system nodes in specific environments and the division of similar areas. Result: It has been verified that the platform is committed to strict monitoring and management of energy-consuming equipment. Conclusion: Realize the reasonable distribution of energy consumption, energy saving, and humanized and automated energy consumption monitoring functions in the office area of large office buildings in modern cities.
- 1 March 2023
- Published by Bentham Science Publishers Ltd. in Recent Advances in Electrical & Electronic Engineering (Formerly Recent Patents on Electrical & Electronic Engineering)
- Vol. 16 (2) , 159-167
Detailed Study on Electronic Data Energy Consumption Monitoring System Based on the Construction of Internet of Things
Aim: To propose a set of dynamic model generation algorithm DPGA, the algorithm can generate parameter models and service models based on user scenarios. Background: Buildings in the traditional sense have become increasingly unable to meet modern humans’ pursuit of high-quality living and working environments, with the pace of urban development, modern buildings have gradually entered people's lives. Objective: Research on Electronic Data Energy Consumption Monitoring System Based on the Construction of Internet of Things. Method: The author made two definitions of the communication format between the middleware and the wireless sensor network, the author has designed the software and hardware functions of the nodes of the system's wireless sensor network, the author implements part of the node. Finally, the author describes the specific implementation of the application program interface and data interface between the modules of the middleware system, and take the internal environment of a typical office building as an example, the author discussed the deployment plan of system nodes in specific environments and the division of similar areas. Result: It has been verified that the platform is committed to strict monitoring and management of energy-consuming equipment. Conclusion: Realize the reasonable distribution of energy consumption, energy saving, and humanized and automated energy consumption monitoring functions in the office area of large office buildings in modern cities.
- 19 April 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (6) , 2756-2764
A review study on the performance enhancement of solar parabolic trough receiver by various passive techniques
This is a new era where the world’s energy consumption is so high and is likely to increase over 60% of current consumption by the year 2030. Therefore, renewable energy should be used most frequently. The most preferred alternative to fossil fuels is solar energy but converting solar energy into usable form is the most challenging part. The conversion to thermal energy is the one option. In the area of solar thermal power generation, a solar parabolic trough (SPT) collector is an effective method. Also, the use of passive methods to enhance the thermal performance of these parabolic trough receivers is currently the researcher’s interest This review study is focused on different types of geometrical modification (Artificial roughness) used to enhance the thermal performance of SPT receivers. Based on the extensive study it has been found that conical strip insert is a very broad field for research as it can enhance the thermal performance up to 5–10 times. Also there are parameters associated with the conical strips like shape, pitch, angle of twist, slant angle, geometry angle, etc. which can contribute to better performance when used in SPT receiver.
- 19 April 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (6) , 2756-2764
A review study on the performance enhancement of solar parabolic trough receiver by various passive techniques
This is a new era where the world’s energy consumption is so high and is likely to increase over 60% of current consumption by the year 2030. Therefore, renewable energy should be used most frequently. The most preferred alternative to fossil fuels is solar energy but converting solar energy into usable form is the most challenging part. The conversion to thermal energy is the one option. In the area of solar thermal power generation, a solar parabolic trough (SPT) collector is an effective method. Also, the use of passive methods to enhance the thermal performance of these parabolic trough receivers is currently the researcher’s interest This review study is focused on different types of geometrical modification (Artificial roughness) used to enhance the thermal performance of SPT receivers. Based on the extensive study it has been found that conical strip insert is a very broad field for research as it can enhance the thermal performance up to 5–10 times. Also there are parameters associated with the conical strips like shape, pitch, angle of twist, slant angle, geometry angle, etc. which can contribute to better performance when used in SPT receiver.
- 29 November 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (4) , 1296-1307
Performance evaluation of solar parabolic trough receiver using multiple twisted tapes with circular perforation and delta winglet
A parabolic trough collector (PTC) is one of the concentrating types of a solar collector working in the medium range of temperature from 100–400 °C, for this reason, the efficiency of the solar parabolic trough is less than other types of concentrating solar collector (Point focusing types) in terms of solar to thermal energy conversion, the improvement in efficiency is achieved by various passive heat augmentation techniques in the receiver tube. One of the promising passive techniques is twisted tape inserts used in the receiver due to its simplicity in design and the various possibility of geometric modification. This paper deals with the performance evaluation of the solar parabolic trough receiver system by using passive techniques in the receiver. The testing of the receiver of PTC was done by using multiple perforated twisted tapes with winglets having different perforation ratios ( ) of 0.05, 0.15, 0.25, twist ratios ( ) of 3, 4, 5 and wing depth ratios ( ) of 0.1, 0.2 and 0.3. The number of twisted tapes was fixed at 4. The examination was conducted for Reynolds numbers ( ) varying from 3000–21,000 using air as working fluid. The outcome shows that the use of perforation and winglet in twisted tapes augment the Nusselt number as compared to that of smooth twisted tapes. The maximum thermohydraulic performance ( ) of 2.40 is received by using multiple twisted tapes with perforation and winglet having = 0.3, = 3, and = 0.05 at the Re = 21,000. The correlations for Nusselt number ( ) and friction factor ( ) are also developed with ± 8.5% and ± 8.3% accuracy, respectively.- 29 November 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (4) , 1296-1307
Performance evaluation of solar parabolic trough receiver using multiple twisted tapes with circular perforation and delta winglet
A parabolic trough collector (PTC) is one of the concentrating types of a solar collector working in the medium range of temperature from 100–400 °C, for this reason, the efficiency of the solar parabolic trough is less than other types of concentrating solar collector (Point focusing types) in terms of solar to thermal energy conversion, the improvement in efficiency is achieved by various passive heat augmentation techniques in the receiver tube. One of the promising passive techniques is twisted tape inserts used in the receiver due to its simplicity in design and the various possibility of geometric modification. This paper deals with the performance evaluation of the solar parabolic trough receiver system by using passive techniques in the receiver. The testing of the receiver of PTC was done by using multiple perforated twisted tapes with winglets having different perforation ratios ( ) of 0.05, 0.15, 0.25, twist ratios ( ) of 3, 4, 5 and wing depth ratios ( ) of 0.1, 0.2 and 0.3. The number of twisted tapes was fixed at 4. The examination was conducted for Reynolds numbers ( ) varying from 3000–21,000 using air as working fluid. The outcome shows that the use of perforation and winglet in twisted tapes augment the Nusselt number as compared to that of smooth twisted tapes. The maximum thermohydraulic performance ( ) of 2.40 is received by using multiple twisted tapes with perforation and winglet having = 0.3, = 3, and = 0.05 at the Re = 21,000. The correlations for Nusselt number ( ) and friction factor ( ) are also developed with ± 8.5% and ± 8.3% accuracy, respectively.- 16 August 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (2) , 699-711
A review study on the performance of a parabolic trough receiver using twisted tape inserts
Heat transfer in concentrating solar collectors like parabolic troughs has proven nowadays a very efficient method by using different passive techniques to increase the heat transfer rate. The use of passive techniques also increases the pumping power requirements to make the flow through the receiver. So, a number of researchers are working to find out the optimum performance conditions for parabolic trough receivers by using different types of inserts in flow paths. This paper presents a wide range of literature available for solar parabolic troughs in one place. Based on this extensive study, it is found that twisted tape inserts is a very wide field for investigation and the use of different shapes, pitch value, free space, and angle of twist tape are the parameters that can be considered for further studies to improve the performance of solar troughs. Also, various combinations of perforation and cuts on twisted tapes can be used to achieve enhanced performance.
- 16 August 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 236 (2) , 699-711
A review study on the performance of a parabolic trough receiver using twisted tape inserts
Heat transfer in concentrating solar collectors like parabolic troughs has proven nowadays a very efficient method by using different passive techniques to increase the heat transfer rate. The use of passive techniques also increases the pumping power requirements to make the flow through the receiver. So, a number of researchers are working to find out the optimum performance conditions for parabolic trough receivers by using different types of inserts in flow paths. This paper presents a wide range of literature available for solar parabolic troughs in one place. Based on this extensive study, it is found that twisted tape inserts is a very wide field for investigation and the use of different shapes, pitch value, free space, and angle of twist tape are the parameters that can be considered for further studies to improve the performance of solar troughs. Also, various combinations of perforation and cuts on twisted tapes can be used to achieve enhanced performance.
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 45, 5097-5101
Effect of heat treatment processes on the mechanical properties of AISI 1045 steel
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 45, 5097-5101
Effect of heat treatment processes on the mechanical properties of AISI 1045 steel
- 21 January 2020
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 142 (3) , 1-39
Innovatively Arranged Curved-Ribbed Solar-Assisted Air Heater: Performance and Correlation Development for Heat and Flow Characteristics
In the present investigation, experiments were conducted to perceive the influence of S shaped roughness element with gaps on flow and heat transfer (HT) characteristics. The studied parameters were relative roughness-width (W/w) ranges from 1-4 (4 different values), relative roughness-pitch (P/e) ranges from 4-16 (4 different values), arc angle (α) varies from 30-75° (4 different values), relative gap width (g/e) ranges from 0.5-2.0 (4 different values), relative gap distance (d/x) ranges from 0.25-0.85 (4 values), relative roughness-height (e/D) varies from 0.18-0.045 (4 different values) and Reynolds number (Re) ranges from 2300 to 23000 (7 different values). Result shows that by providing S-shaped roughness with gap augments considerable amount of heat transfer (Nu) along with friction factor. Correlations developed for Nu and f for the mentioned assortment of all investigated constraints.
- 21 January 2020
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 142 (3) , 1-39
Innovatively Arranged Curved-Ribbed Solar-Assisted Air Heater: Performance and Correlation Development for Heat and Flow Characteristics
In the present investigation, experiments were conducted to perceive the influence of S shaped roughness element with gaps on flow and heat transfer (HT) characteristics. The studied parameters were relative roughness-width (W/w) ranges from 1-4 (4 different values), relative roughness-pitch (P/e) ranges from 4-16 (4 different values), arc angle (α) varies from 30-75° (4 different values), relative gap width (g/e) ranges from 0.5-2.0 (4 different values), relative gap distance (d/x) ranges from 0.25-0.85 (4 values), relative roughness-height (e/D) varies from 0.18-0.045 (4 different values) and Reynolds number (Re) ranges from 2300 to 23000 (7 different values). Result shows that by providing S-shaped roughness with gap augments considerable amount of heat transfer (Nu) along with friction factor. Correlations developed for Nu and f for the mentioned assortment of all investigated constraints.