Serhan Ilkentapar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Serhan Ilkentapar has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Uğur Durak
Civil Engineering Department Erciyes University Kayseri Turkey
13 shared publications - Cengiz Duran Atiş
Department of Civil Engineering, Erciyes University, Kayseri 38039, Turkey
11 shared publications - Okan Karahan
Erciyes University
11 shared publications - İsmail İsa Atabey
Nevşehir Hacı Bektaş Veli University, Department of Civil Engineering, Nevşehir, Türkiye
6 shared publications - Halil Eren
ERCİYES ÜNİVERSİTES
2 shared publications - Hediye Yorulmaz
Civil Engineering Department, Abdullah Gül University, Kayseri, Turkey
2 shared publications
Latest Publications
- Open Access
Hemp Fiber and Expanded Perlite-Incorporated Lightweight Inorganic Polymer Mortars: Mechanical, Thermal Insulation, High-Temperature Resistance, Microstructural Characteristics, and Life Cycle Assessment
In this study, lightweight geopolymer mortars with low environmental impact, high thermal insulation performance, and strong resistance to elevated temperatures were developed. Fly ash, expanded perlite, and bio-based hemp fibers were employed as the binder, aggregate, and reinforcement, respectively. Hemp fibers were prepared in lengths of 1, 2, and 3 cm and incorporated into the mixtures at dosages of 0.50%, 0.75%, and 1.00% by weight of binder. Sodium hydroxide was used as the activator, and specimens were heat-cured at 90 °C for 24–48–72 h. The workability, unit weight, UPV, flexural, and compressive strength of the geopolymer mortars were determined. In addition, thermal conductivity, high-temperature resistance, microstructural characteristics, and environmental impacts of selected mixtures were evaluated. The results demonstrated that lightweight geopolymer mortars could be successfully produced using expanded perlite aggregate and that hemp fibers significantly enhanced mechanical performance up to 48% at one day. Moreover, fiber reinforcement improved thermal insulation capability by up to 5.5% and high-temperature resistance. FESEM, EDX, elemental mapping, and XRD analyses supported the mechanical and physical findings through detailed microstructural evidence. Furthermore, LCA results revealed that fiber incorporation improved the environmental performance of geopolymer mortars, resulting in approximately a 21% reduction in global warming potential compared with the reference mixture.
Open AccessHemp Fiber and Expanded Perlite-Incorporated Lightweight Inorganic Polymer Mortars: Mechanical, Thermal Insulation, High-Temperature Resistance, Microstructural Characteristics, and Life Cycle Assessment
In this study, lightweight geopolymer mortars with low environmental impact, high thermal insulation performance, and strong resistance to elevated temperatures were developed. Fly ash, expanded perlite, and bio-based hemp fibers were employed as the binder, aggregate, and reinforcement, respectively. Hemp fibers were prepared in lengths of 1, 2, and 3 cm and incorporated into the mixtures at dosages of 0.50%, 0.75%, and 1.00% by weight of binder. Sodium hydroxide was used as the activator, and specimens were heat-cured at 90 °C for 24–48–72 h. The workability, unit weight, UPV, flexural, and compressive strength of the geopolymer mortars were determined. In addition, thermal conductivity, high-temperature resistance, microstructural characteristics, and environmental impacts of selected mixtures were evaluated. The results demonstrated that lightweight geopolymer mortars could be successfully produced using expanded perlite aggregate and that hemp fibers significantly enhanced mechanical performance up to 48% at one day. Moreover, fiber reinforcement improved thermal insulation capability by up to 5.5% and high-temperature resistance. FESEM, EDX, elemental mapping, and XRD analyses supported the mechanical and physical findings through detailed microstructural evidence. Furthermore, LCA results revealed that fiber incorporation improved the environmental performance of geopolymer mortars, resulting in approximately a 21% reduction in global warming potential compared with the reference mixture.
- 20 March 2024
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 48 (5) , 3559-3572
Physical Mechanical and Microstructural Properties of Kaolin-Based Fly Ash-Added Geopolymer Mortars
- 20 March 2024
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 48 (5) , 3559-3572
Physical Mechanical and Microstructural Properties of Kaolin-Based Fly Ash-Added Geopolymer Mortars
- Open Access
- 31 January 2023
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 11 (1) , 288-301
Geri Dönüştürülmüş Atık EPS'nin Yüksek Dayanımlı Hafif Şap Üretiminde Kullanımının Araştırılması
Bu çalışmada, atık genleştirilmiş polistiren (EPS) agregası dere kumu ile yer değiştirerek yüksek dayanımlı hafif şap harçları üretilmiştir. Kaplama ve tesviye amacı ile kullanılan şap harçlarında, atık EPS kullanarak harçların birim hacim ağırlığının azaltılması, ısıl performanslarının arttırılması hedeflenmiştir. Bu amaçla, bir grup geleneksel şap harcı ve beş grup atık EPS içeren, 400 kg/m³ -500 kg/m³ arasında değişen çimento dozajlarına sahip hafif şap harcı hazırlanmıştır. Atık EPS agregaları, dere agregası ile hacimce %0, %20, %40, %60, %80 ve %100 oranında yer değiştirilmiştir. Geleneksel ve hafif şap harçlarının yayılma çapı, birim ağırlık, su emme oranı, görünür boşluk oranı, kılcal su emme, basınç ve eğilme dayanımı, aşınmaya karşı direnç ve ısıl iletkenlik performansı ölçülmüştür. Atık EPS içeren harçların birim hacim ağırlıkları 750 kg/m³ –1950 kg/m³ arasında belirlenerek hafif ağırlıklı şap harcı elde edilmiştir. Ayrıca geleneksel şap harcının ısıl iletkenlik katsayısı 0,6617 W.m/K’dan tamamen atık EPS ikamesi ile 0,2553 W.m/K’ya düşerek %61 daha düşük ısıl iletkenlik elde edilmiştir. Deneysel sonuçlar atık EPS agregasının yer değişim oranına bağlı olarak 6,1 MPa-43,4 MPa aralığında hem orta dayanımlı hem de taşıyıcı hafif beton sınıfında hafif şap harçlarının elde edilebildiğini ortaya koymuştur. Harçlardaki birim ağırlığın düşmesi, yapı ağırlığının azalmasına ve ısıl yalıtım özelliğinin iyileşmesine katkı sunmaktadır. Böylece deprem yükü, yalıtım özellikleri ve atık EPS’nin geri dönüşümü açısından sürdürülebilir hafif şap harcı elde edilmiştir.
- 31 January 2023
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 11 (1) , 288-301
Open AccessGeri Dönüştürülmüş Atık EPS'nin Yüksek Dayanımlı Hafif Şap Üretiminde Kullanımının Araştırılması
Bu çalışmada, atık genleştirilmiş polistiren (EPS) agregası dere kumu ile yer değiştirerek yüksek dayanımlı hafif şap harçları üretilmiştir. Kaplama ve tesviye amacı ile kullanılan şap harçlarında, atık EPS kullanarak harçların birim hacim ağırlığının azaltılması, ısıl performanslarının arttırılması hedeflenmiştir. Bu amaçla, bir grup geleneksel şap harcı ve beş grup atık EPS içeren, 400 kg/m³ -500 kg/m³ arasında değişen çimento dozajlarına sahip hafif şap harcı hazırlanmıştır. Atık EPS agregaları, dere agregası ile hacimce %0, %20, %40, %60, %80 ve %100 oranında yer değiştirilmiştir. Geleneksel ve hafif şap harçlarının yayılma çapı, birim ağırlık, su emme oranı, görünür boşluk oranı, kılcal su emme, basınç ve eğilme dayanımı, aşınmaya karşı direnç ve ısıl iletkenlik performansı ölçülmüştür. Atık EPS içeren harçların birim hacim ağırlıkları 750 kg/m³ –1950 kg/m³ arasında belirlenerek hafif ağırlıklı şap harcı elde edilmiştir. Ayrıca geleneksel şap harcının ısıl iletkenlik katsayısı 0,6617 W.m/K’dan tamamen atık EPS ikamesi ile 0,2553 W.m/K’ya düşerek %61 daha düşük ısıl iletkenlik elde edilmiştir. Deneysel sonuçlar atık EPS agregasının yer değişim oranına bağlı olarak 6,1 MPa-43,4 MPa aralığında hem orta dayanımlı hem de taşıyıcı hafif beton sınıfında hafif şap harçlarının elde edilebildiğini ortaya koymuştur. Harçlardaki birim ağırlığın düşmesi, yapı ağırlığının azalmasına ve ısıl yalıtım özelliğinin iyileşmesine katkı sunmaktadır. Böylece deprem yükü, yalıtım özellikleri ve atık EPS’nin geri dönüşümü açısından sürdürülebilir hafif şap harcı elde edilmiştir.
- Open Access
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (3) , 581-596
Recycling waste expanded polystyrene as aggregate in produc-tion of lightweight screed mortar
The potential use of waste-expanded polystyrene (EPS) beads in the production of lightweight screed mortar (LSM) was investigated. LSM specimens were produced by replacing waste EPS with normal weight aggregate at 20%, 40%, 60%, 80%, and 100% proportions by volume. Workability, unit weight, capillarity, flexural and compressive strength, abrasion resistance, drying shrinkage, and thermal conductivity of the LSMs were determined. Waste EPS replacement by the normal weight aggregate reduced the abrasion resistance and strength properties of LSMs. Waste EPS also caused the LSMs to have lower unit weight and thermal conductivity, significantly. It was concluded that substitution of waste EPS by normal weight aggregate up to 60% can be proposed for adequate strength and heat-insulating properties of LSMs. LSM produced with 60% waste EPS (M60) has 16.3 MPa 28th-day compressive strength with 0.4562 W/m.K thermal conductivity and 1.35 g/cm3 unit weight. Moreover, the recovery of waste EPS contributes to both reducing environmental pollution and storage problems.
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (3) , 581-596
Open AccessRecycling waste expanded polystyrene as aggregate in produc-tion of lightweight screed mortar
The potential use of waste-expanded polystyrene (EPS) beads in the production of lightweight screed mortar (LSM) was investigated. LSM specimens were produced by replacing waste EPS with normal weight aggregate at 20%, 40%, 60%, 80%, and 100% proportions by volume. Workability, unit weight, capillarity, flexural and compressive strength, abrasion resistance, drying shrinkage, and thermal conductivity of the LSMs were determined. Waste EPS replacement by the normal weight aggregate reduced the abrasion resistance and strength properties of LSMs. Waste EPS also caused the LSMs to have lower unit weight and thermal conductivity, significantly. It was concluded that substitution of waste EPS by normal weight aggregate up to 60% can be proposed for adequate strength and heat-insulating properties of LSMs. LSM produced with 60% waste EPS (M60) has 16.3 MPa 28th-day compressive strength with 0.4562 W/m.K thermal conductivity and 1.35 g/cm3 unit weight. Moreover, the recovery of waste EPS contributes to both reducing environmental pollution and storage problems.
- Open Access
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (2) , 419-430
Synergistic effect of waste glass powder and fly ash on some properties of mortar and notably suppressing alkali-silica reaction
In this study the mitigation influence of incorporating waste glass powder (G) and class F fly ash (F) in mortar as partial cement replacement on the alkali-silica reaction (ASR) between reactive aggregate and alkali contents of cement were investigated. Waste G and F replaced cement separately and together on mass basis at 10%, 20%, and 30%. The unit weight (28 days), water absorption, porosity, compressive, and flexural strength tests were conducted at 28- and 90-day water curing time on 40×40×160 mm prismatic hardened samples and flow table test on fresh mortar. There was a slight reduction of the unit weight, an increased workability, and decreased water absorption and porosity; a little reduction of the compressive strength and flexural strength were seen after the tests. In addition, the expansions of mortar were measured up to 90 days. When 14 days expansions were considered according to ASTM C1260, addition of waste G and F separately reduced the expansion that occurred due to ASR. However, the mixture containing 15% waste G and 15% F together (GF-30) exhibited the lowest expansion in the order of 0.02% which was far lower than 0.10%. The higher replacement ratio of waste G and F together and separately caused lower expansion in mortar.
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (2) , 419-430
Open AccessSynergistic effect of waste glass powder and fly ash on some properties of mortar and notably suppressing alkali-silica reaction
In this study the mitigation influence of incorporating waste glass powder (G) and class F fly ash (F) in mortar as partial cement replacement on the alkali-silica reaction (ASR) between reactive aggregate and alkali contents of cement were investigated. Waste G and F replaced cement separately and together on mass basis at 10%, 20%, and 30%. The unit weight (28 days), water absorption, porosity, compressive, and flexural strength tests were conducted at 28- and 90-day water curing time on 40×40×160 mm prismatic hardened samples and flow table test on fresh mortar. There was a slight reduction of the unit weight, an increased workability, and decreased water absorption and porosity; a little reduction of the compressive strength and flexural strength were seen after the tests. In addition, the expansions of mortar were measured up to 90 days. When 14 days expansions were considered according to ASTM C1260, addition of waste G and F separately reduced the expansion that occurred due to ASR. However, the mixture containing 15% waste G and 15% F together (GF-30) exhibited the lowest expansion in the order of 0.02% which was far lower than 0.10%. The higher replacement ratio of waste G and F together and separately caused lower expansion in mortar.
- 31 December 2022
- Published by Echo Academic Publishing in Environmental Research and Technology
- Vol. 5 (4) , 289-295
Comparison of Mechanical and Physical Properties of Screed with and without Expanded Polystyrene (EPS) Particles
In this study, in order to observe the mechanical and physical properties of ordinary screed, sandy-lightweight screed and lightweight screed samples, expanded polystyrene (EPS) was used as fine aggregate and lightweight screed systems were produced by replacing sand at 100%, 50% and 0%. Samples of cement dosages of 250, 300, 350 kg/m3 were produced for lightweight screeds, sandy-lightweight screeds and ordinary screeds. Unit weight, water absorption capacity, flexural strength, compressive strength, fire resistance, abrasion and thermal conductivity tests were performed on the produced screed systems. As a result of the research, it was determined that as EPS ratio increases in screed system; unit weights decreased, water absorption rates increased. Besides, the flexural and compressive strengths, fire and abrasion resistance are also decreased. However, it was observed that the thermal conductivity coefficient reduced with the increment of EPS particles in the screed. In normal, sandy-lightweight and lightweight screeds, it was determined that as the cement dosage increased; the unit weights, flexural and compressive strengths, fire and abrasion resistance increased, water absorption capacity and the thermal conductivity coefficient decreased.
- 31 December 2022
- Published by Echo Academic Publishing in Environmental Research and Technology
- Vol. 5 (4) , 289-295
Comparison of Mechanical and Physical Properties of Screed with and without Expanded Polystyrene (EPS) Particles
In this study, in order to observe the mechanical and physical properties of ordinary screed, sandy-lightweight screed and lightweight screed samples, expanded polystyrene (EPS) was used as fine aggregate and lightweight screed systems were produced by replacing sand at 100%, 50% and 0%. Samples of cement dosages of 250, 300, 350 kg/m3 were produced for lightweight screeds, sandy-lightweight screeds and ordinary screeds. Unit weight, water absorption capacity, flexural strength, compressive strength, fire resistance, abrasion and thermal conductivity tests were performed on the produced screed systems. As a result of the research, it was determined that as EPS ratio increases in screed system; unit weights decreased, water absorption rates increased. Besides, the flexural and compressive strengths, fire and abrasion resistance are also decreased. However, it was observed that the thermal conductivity coefficient reduced with the increment of EPS particles in the screed. In normal, sandy-lightweight and lightweight screeds, it was determined that as the cement dosage increased; the unit weights, flexural and compressive strengths, fire and abrasion resistance increased, water absorption capacity and the thermal conductivity coefficient decreased.
- Open Access
- 26 December 2022
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 10 (5) , 114-126
Alkali ile Aktive Edilmiş Cüruf ve Uçucu Kül Harçlarına Yüksek Sıcaklık Sonrası Hava Kürünün Etkisi
Bu çalışmada alkali ile aktive edilmiş yüksek fırın cürufu ve uçucu kül içeren harçların dayanım özelliklerine yüksek sıcaklık sonrası hava kürü koşullarının etkisi araştırılmıştır. Bu amaçla uçucu kül %0, %25, %50, %75, %100 oranlarında yüksek fırın cürufu ile ikame edilerek alkali ile aktive edilmiş harçlar üretilmiştir. Harçlarda aktivatör olarak %10 oranında Sodyum (Na) içeren sodyum metasilikat kullanılmıştır. Üretilen harçlar 24 saat 90°C ısıl küre tabi tutulmuştur. Isıl kür sonrası numuneler 400, 600 ve 800oC’de yüksek sıcaklığa maruz bırakılmıştır. Referans grubu numuneleri etüv kürü uygulandıktan sonra, birinci grup numuneler yüksek sıcaklık uygulandıktan 1 gün sonra, ikinci grup numuneler ise yüksek sıcaklık uygulandıktan 28 gün sonra ağırlık kaybı, eğilme dayanımı ve basınç dayanımı testlerine tabi tutulmuştur. Yüksek sıcaklık öncesi en yüksek basınç dayanım 75,5 MPa ile %100 cüruflu numunelerde elde edilirken en düşük basınç dayanımı 44,6 MPa ile %100 uçucu kül içeren numunelerde elde edilmiştir. Yüksek sıcaklıktan sonra 28 gün havada kür uygulanan numunelerin basınç dayanım değerleri yüksek sıcaklığa maruz kalmayan numunelerin basınç dayanım değerleri ile karşılaştırıldığında,400oC, 600oC ve 800oC’de sırasıyla en fazla %32, %64 ve %93 basınç dayanımı kaybı meydana gelmiştir. Numunelerin yüksek sıcaklık sonrası 1 ve 28 gün süreyle havada kür edilmesi, basınç dayanımlarında önemli bir değişikliğe neden olmamıştır. Yüksek sıcaklık sonrası eğilme ve basınç dayanımı kaybı hemen oluşmuş, 28 gün hava kürü ile numuneler genel olarak basınç dayanımlarını korumuşlardır.
- 26 December 2022
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 10 (5) , 114-126
Open AccessAlkali ile Aktive Edilmiş Cüruf ve Uçucu Kül Harçlarına Yüksek Sıcaklık Sonrası Hava Kürünün Etkisi
Bu çalışmada alkali ile aktive edilmiş yüksek fırın cürufu ve uçucu kül içeren harçların dayanım özelliklerine yüksek sıcaklık sonrası hava kürü koşullarının etkisi araştırılmıştır. Bu amaçla uçucu kül %0, %25, %50, %75, %100 oranlarında yüksek fırın cürufu ile ikame edilerek alkali ile aktive edilmiş harçlar üretilmiştir. Harçlarda aktivatör olarak %10 oranında Sodyum (Na) içeren sodyum metasilikat kullanılmıştır. Üretilen harçlar 24 saat 90°C ısıl küre tabi tutulmuştur. Isıl kür sonrası numuneler 400, 600 ve 800oC’de yüksek sıcaklığa maruz bırakılmıştır. Referans grubu numuneleri etüv kürü uygulandıktan sonra, birinci grup numuneler yüksek sıcaklık uygulandıktan 1 gün sonra, ikinci grup numuneler ise yüksek sıcaklık uygulandıktan 28 gün sonra ağırlık kaybı, eğilme dayanımı ve basınç dayanımı testlerine tabi tutulmuştur. Yüksek sıcaklık öncesi en yüksek basınç dayanım 75,5 MPa ile %100 cüruflu numunelerde elde edilirken en düşük basınç dayanımı 44,6 MPa ile %100 uçucu kül içeren numunelerde elde edilmiştir. Yüksek sıcaklıktan sonra 28 gün havada kür uygulanan numunelerin basınç dayanım değerleri yüksek sıcaklığa maruz kalmayan numunelerin basınç dayanım değerleri ile karşılaştırıldığında,400oC, 600oC ve 800oC’de sırasıyla en fazla %32, %64 ve %93 basınç dayanımı kaybı meydana gelmiştir. Numunelerin yüksek sıcaklık sonrası 1 ve 28 gün süreyle havada kür edilmesi, basınç dayanımlarında önemli bir değişikliğe neden olmamıştır. Yüksek sıcaklık sonrası eğilme ve basınç dayanımı kaybı hemen oluşmuş, 28 gün hava kürü ile numuneler genel olarak basınç dayanımlarını korumuşlardır.
- 30 June 2022
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 10 (2) , 360-370
COMPARISON OF THE MECHANICAL PROPERTIES, HEAT PERMEABİLİTY CHARACTERISTICS AND RESISTANCE AGAINST HIGH TEMPERATURE OF LIGHT MORTARS MADE WITH EPS AND WASTE POLYURETHANE
Bu çalışmada endüstriyel işlem sonrası açığa çıkan atık poliüretanın hafif harç imalatında kullanımı araştırılmıştır. Hali hazırda hafif harç üretiminde kullanılan EPS (Expanded polystyren foam) ve atık poliüretan kullanılarak hafif harç numuneler üretilmiştir. Üretilen numuneler eşdeğer birim ağırlıklarına göre karşılaştırılarak, atık poliüretanın hafif harç imalatında kullanımı araştırılmıştır. Çalışma kapsamında EPS ve atık poliüretan agrega ile hacimce %20, %40, %60, %80, %100 oranlarında yer değiştirilerek kullanılmış ve 40x40x160 mm’lik prizmatik harç numuneler üretilmiştir. Üretilen harç numunelerin birim ağırlık değerleri, ultrasonik atımlı dalga hızları, ısı iletkenlik katsayıları ile eğilme ve basınç dayanımları ölçülmüştür. Ayrıca hem EPS hem de atık poliüretan ile üretilmiş harç numuneler 300⁰C, 600⁰C, 900⁰C’de yüksek sıcaklığa tabi tutulmuş ve sonrasında numunelerin mekanik dayanımları ile içyapıları incelenmiştir. İçyapı incelemeleri hamur numuneler üzerinde FESEM görüntüleri ile gerçekleştirilmiştir. Elde edilen verilere göre hem orta mukavemetli hafif beton sınıfına giren harçlarda, hem de taşıyıcı hafif beton sınıfına giren harçlarda atık poliüretan ile imal edilen harçların EPS’li harçlara göre daha iyi performans gösterdiği sonucuna varılmıştır. Özellikle yüksek sıcaklık sonrası mekanik dayanımlar incelendiğinde atık poliüretanlı harç numunelerin, EPS’li numunelere oranla daha yüksek eğilme ve basınç dayanımları verdiği tespit edilmiştir.
- 30 June 2022
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 10 (2) , 360-370
COMPARISON OF THE MECHANICAL PROPERTIES, HEAT PERMEABİLİTY CHARACTERISTICS AND RESISTANCE AGAINST HIGH TEMPERATURE OF LIGHT MORTARS MADE WITH EPS AND WASTE POLYURETHANE
Bu çalışmada endüstriyel işlem sonrası açığa çıkan atık poliüretanın hafif harç imalatında kullanımı araştırılmıştır. Hali hazırda hafif harç üretiminde kullanılan EPS (Expanded polystyren foam) ve atık poliüretan kullanılarak hafif harç numuneler üretilmiştir. Üretilen numuneler eşdeğer birim ağırlıklarına göre karşılaştırılarak, atık poliüretanın hafif harç imalatında kullanımı araştırılmıştır. Çalışma kapsamında EPS ve atık poliüretan agrega ile hacimce %20, %40, %60, %80, %100 oranlarında yer değiştirilerek kullanılmış ve 40x40x160 mm’lik prizmatik harç numuneler üretilmiştir. Üretilen harç numunelerin birim ağırlık değerleri, ultrasonik atımlı dalga hızları, ısı iletkenlik katsayıları ile eğilme ve basınç dayanımları ölçülmüştür. Ayrıca hem EPS hem de atık poliüretan ile üretilmiş harç numuneler 300⁰C, 600⁰C, 900⁰C’de yüksek sıcaklığa tabi tutulmuş ve sonrasında numunelerin mekanik dayanımları ile içyapıları incelenmiştir. İçyapı incelemeleri hamur numuneler üzerinde FESEM görüntüleri ile gerçekleştirilmiştir. Elde edilen verilere göre hem orta mukavemetli hafif beton sınıfına giren harçlarda, hem de taşıyıcı hafif beton sınıfına giren harçlarda atık poliüretan ile imal edilen harçların EPS’li harçlara göre daha iyi performans gösterdiği sonucuna varılmıştır. Özellikle yüksek sıcaklık sonrası mekanik dayanımlar incelendiğinde atık poliüretanlı harç numunelerin, EPS’li numunelere oranla daha yüksek eğilme ve basınç dayanımları verdiği tespit edilmiştir.