Mark A. Arnould
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mark A. Arnould has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Chrys Wesdemiotis
The University of Akron
9 shared publications Chrys Wesdemiotis
Maurice Morton Institute of Polymer Science, The University of Akron, Akron, Ohio 44325-3909, and Department of Chemistry, The University of Akron, Akron, Ohio 44325-3601
5 shared publicationsRoderic P. Quirk
Maurice Morton Institute of Polymer Science, The University of Akron, Akron, Ohio 44325-3909, and Department of Chemistry, The University of Akron, Akron, Ohio 44325-3601
5 shared publications- Ali Goger
Department of Chemical Engineering Karabuk University Karabuk Turkey
4 shared publications - Michael R. Thompson
Department of Chemical Engineering, McMaster University, Hamilton, ON, Canada
4 shared publications - Roderic P. Quirk
Institute of Polymer Science and Polymer Engineering, The University of Akron, Akron, Ohio 44325, USA
4 shared publications
Latest Publications
- 1 December 2024
- Published by Office of Scientific and Technical Information (OSTI)
Coal to Carbon Fibers
- 1 December 2024
- Published by Office of Scientific and Technical Information (OSTI)
Coal to Carbon Fibers
- Open Access
- 24 July 2023
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 10 (9) , 3360-3368
Selective deconstruction of mixed plastics by a tailored organocatalyst
The developed highly efficient and versatile organocatalyst can deconstruct multiple condensation polymers selectively and sequentially into corresponding monomers, while keeping other polymers such as polyolefins or cotton intact.
- 24 July 2023
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 10 (9) , 3360-3368
Open AccessSelective deconstruction of mixed plastics by a tailored organocatalyst
The developed highly efficient and versatile organocatalyst can deconstruct multiple condensation polymers selectively and sequentially into corresponding monomers, while keeping other polymers such as polyolefins or cotton intact.
- Open Access
- 27 April 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-11
Covalent narlaprevir- and boceprevir-derived hybrid inhibitors of SARS-CoV-2 main protease
Emerging SARS-CoV-2 variants continue to threaten the effectiveness of COVID-19 vaccines, and small-molecule antivirals can provide an important therapeutic treatment option. The viral main protease (Mpro) is critical for virus replication and thus is considered an attractive drug target. We performed the design and characterization of three covalent hybrid inhibitors BBH-1, BBH-2 and NBH-2 created by splicing components of hepatitis C protease inhibitors boceprevir and narlaprevir, and known SARS-CoV-1 protease inhibitors. A joint X-ray/neutron structure of the Mpro/BBH-1 complex demonstrates that a Cys145 thiolate reaction with the inhibitor’s keto-warhead creates a negatively charged oxyanion. Protonation states of the ionizable residues in the Mpro active site adapt to the inhibitor, which appears to be an intrinsic property of Mpro. Structural comparisons of the hybrid inhibitors with PF-07321332 reveal unconventional F···O interactions of PF-07321332 with Mpro which may explain its more favorable enthalpy of binding. BBH-1, BBH-2 and NBH-2 exhibit comparable antiviral properties in vitro relative to PF-07321332, making them good candidates for further design of improved antivirals.
- 27 April 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-11
Open AccessCovalent narlaprevir- and boceprevir-derived hybrid inhibitors of SARS-CoV-2 main protease
Emerging SARS-CoV-2 variants continue to threaten the effectiveness of COVID-19 vaccines, and small-molecule antivirals can provide an important therapeutic treatment option. The viral main protease (Mpro) is critical for virus replication and thus is considered an attractive drug target. We performed the design and characterization of three covalent hybrid inhibitors BBH-1, BBH-2 and NBH-2 created by splicing components of hepatitis C protease inhibitors boceprevir and narlaprevir, and known SARS-CoV-1 protease inhibitors. A joint X-ray/neutron structure of the Mpro/BBH-1 complex demonstrates that a Cys145 thiolate reaction with the inhibitor’s keto-warhead creates a negatively charged oxyanion. Protonation states of the ionizable residues in the Mpro active site adapt to the inhibitor, which appears to be an intrinsic property of Mpro. Structural comparisons of the hybrid inhibitors with PF-07321332 reveal unconventional F···O interactions of PF-07321332 with Mpro which may explain its more favorable enthalpy of binding. BBH-1, BBH-2 and NBH-2 exhibit comparable antiviral properties in vitro relative to PF-07321332, making them good candidates for further design of improved antivirals.
- Open Access
- 11 February 2022
- Published by Springer Nature in Research Square
Covalent narlaprevir- and boceprevir-derived hybrid inhibitors of SARS-CoV-2 main protease: room-temperature X-ray and neutron crystallography, binding thermodynamics, and antiviral activity
The COVID-19 pandemic continues to disrupt everyday life, with constantly emerging SARS-CoV-2 variants threatening to render current vaccines ineffective. Small-molecule antivirals can provide an important therapeutic treatment option that is subject to challenges caused by the virus variants. The viral main protease (Mpro) is critical for the virus replication and thus is considered an attractive drug target for specific protease inhibitors. We performed the design and characterization of three reversible covalent hybrid inhibitors BBH-1, BBH-2 and NBH-2, whose structures were derived from those of hepatitis C protease inhibitors boceprevir and narlaprevir. A joint X-ray/neutron structure of the Mpro/BBH-1 complex demonstrated that a Cys145 thiolate reaction with the inhibitor’s keto-warhead creates a negatively charged oxyanion, similar to that proposed for the Mpro-catalyzed peptide bond hydrolysis. Protonation states of the ionizable residues in the Mpro active site adapt to the inhibitor, which appears to be an intrinsic property of Mpro. Structural comparisons of the hybrid inhibitors with PF-07321332 revealed unconventional interactions of PF-07321332 with Mpro which may explain its more favorable enthalpy of binding and consequently higher potency. BBH-1, BBH-2 and NBH-2 demonstrated comparable antiviral properties in vitro relative to PF-07321332, making them good candidates for further design of improved antivirals.
- 11 February 2022
- Published by Springer Nature in Research Square
Open AccessCovalent narlaprevir- and boceprevir-derived hybrid inhibitors of SARS-CoV-2 main protease: room-temperature X-ray and neutron crystallography, binding thermodynamics, and antiviral activity
The COVID-19 pandemic continues to disrupt everyday life, with constantly emerging SARS-CoV-2 variants threatening to render current vaccines ineffective. Small-molecule antivirals can provide an important therapeutic treatment option that is subject to challenges caused by the virus variants. The viral main protease (Mpro) is critical for the virus replication and thus is considered an attractive drug target for specific protease inhibitors. We performed the design and characterization of three reversible covalent hybrid inhibitors BBH-1, BBH-2 and NBH-2, whose structures were derived from those of hepatitis C protease inhibitors boceprevir and narlaprevir. A joint X-ray/neutron structure of the Mpro/BBH-1 complex demonstrated that a Cys145 thiolate reaction with the inhibitor’s keto-warhead creates a negatively charged oxyanion, similar to that proposed for the Mpro-catalyzed peptide bond hydrolysis. Protonation states of the ionizable residues in the Mpro active site adapt to the inhibitor, which appears to be an intrinsic property of Mpro. Structural comparisons of the hybrid inhibitors with PF-07321332 revealed unconventional interactions of PF-07321332 with Mpro which may explain its more favorable enthalpy of binding and consequently higher potency. BBH-1, BBH-2 and NBH-2 demonstrated comparable antiviral properties in vitro relative to PF-07321332, making them good candidates for further design of improved antivirals.
- 22 August 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 57 (36) , 12071-12077
Effect of Viscosity on Solvent-Free Extrusion Emulsification: Varying System Temperature
- 22 August 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 57 (36) , 12071-12077
Effect of Viscosity on Solvent-Free Extrusion Emulsification: Varying System Temperature
- 9 January 2018
- Published by Wiley in AIChE Journal
- Vol. 64 (6) , 2113-2123
Solvent‐free polymer emulsification inside a twin‐screw extruder
Solvent‐free extrusion emulsification (SFEE) is new technique for a twin‐screw extruder to prepare submicron‐sized particles (100–500 nm) without using hazardous solvents. The particle size is reliant upon the thickness of striated lamellae, which can be monitored rheologically based on the viscosity change occurring at the SFEE process. The lamellae coarsening rate is predominantly affected by the interfacial energy of the system when a surfactant is added but shows stronger dependency on viscosity change when interfacial growth between the polymer and water phases is solely determined by the end‐groups conversion into carboxylate species. For this latter case, the dissolution of the sodium hydroxide species and the kinetics of end‐groups conversion prove to be rate‐limiting phenomena to generating thinner striated lamellae. Additionally, the ionic strength of the system is notably important to the viscosity response and particle size produced, particularly when surfactant is not added. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2113–2123, 2018
- 9 January 2018
- Published by Wiley in AIChE Journal
- Vol. 64 (6) , 2113-2123
Solvent‐free polymer emulsification inside a twin‐screw extruder
Solvent‐free extrusion emulsification (SFEE) is new technique for a twin‐screw extruder to prepare submicron‐sized particles (100–500 nm) without using hazardous solvents. The particle size is reliant upon the thickness of striated lamellae, which can be monitored rheologically based on the viscosity change occurring at the SFEE process. The lamellae coarsening rate is predominantly affected by the interfacial energy of the system when a surfactant is added but shows stronger dependency on viscosity change when interfacial growth between the polymer and water phases is solely determined by the end‐groups conversion into carboxylate species. For this latter case, the dissolution of the sodium hydroxide species and the kinetics of end‐groups conversion prove to be rate‐limiting phenomena to generating thinner striated lamellae. Additionally, the ionic strength of the system is notably important to the viscosity response and particle size produced, particularly when surfactant is not added. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2113–2123, 2018
- 25 October 2017
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 56 (44) , 12538-12546
Effect of Viscosity on Solvent-Free Extrusion Emulsification: Molecular Structure
- 25 October 2017
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 56 (44) , 12538-12546
Effect of Viscosity on Solvent-Free Extrusion Emulsification: Molecular Structure
- 3 May 2017
- Published by Wiley in Polymer Engineering & Science
- Vol. 58 (5) , 775-783
Inline rheological behavior of dispersed water in a polyester matrix with a twin screw extruder
Solvent‐free extrusion emulsification (SFEE) is a complex process using twin‐screw extrusion to prepare solid‐liquid dispersions of high viscosity polymers and has received little study to date on its inherent mechanisms. To gain rheological insights into the earliest stage of SFEE as the interfacial boundary between water and polymer grows, prior to phase inversion, an inline orifice‐plate type viscometer is introduced to monitor transient behavior over a wide range of viscosities. The presented work examines rheological changes of a polyester‐water system produced by varying two factors thought to significantly control the final state of the dispersion, specifically polar group contributions to surface energy and viscosity. A processing modifier was combined with the polyester to study the influence of these two factors. The inline viscometer revealed an abrupt transition in viscosity occurred with the developed state of water dispersion, confirming observations of a prior batch study. Analysis of the rheological response indicated that a higher polar surface energy contribution had the greatest influence on the state of this transition, and that a steeper transition was related to greater incorporation of water within the polyester matrix. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers
- 3 May 2017
- Published by Wiley in Polymer Engineering & Science
- Vol. 58 (5) , 775-783
Inline rheological behavior of dispersed water in a polyester matrix with a twin screw extruder
Solvent‐free extrusion emulsification (SFEE) is a complex process using twin‐screw extrusion to prepare solid‐liquid dispersions of high viscosity polymers and has received little study to date on its inherent mechanisms. To gain rheological insights into the earliest stage of SFEE as the interfacial boundary between water and polymer grows, prior to phase inversion, an inline orifice‐plate type viscometer is introduced to monitor transient behavior over a wide range of viscosities. The presented work examines rheological changes of a polyester‐water system produced by varying two factors thought to significantly control the final state of the dispersion, specifically polar group contributions to surface energy and viscosity. A processing modifier was combined with the polyester to study the influence of these two factors. The inline viscometer revealed an abrupt transition in viscosity occurred with the developed state of water dispersion, confirming observations of a prior batch study. Analysis of the rheological response indicated that a higher polar surface energy contribution had the greatest influence on the state of this transition, and that a steeper transition was related to greater incorporation of water within the polyester matrix. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers
- Open Access
- 31 March 2015
- Published by Royal Society of Chemistry (RSC) in Chemical Science
- Vol. 6 (5) , 3225-3235
Is a polymer semiconductor having a “perfect” regular structure desirable for organic thin film transistors?
This study utilized high temperature NMR and matrix-assisted laser desorption/ionization time-of-flight (MALDI-ToF) mass spectrometry to reveal that appreciable amounts of structural defects are present in the diketopyrrolopyrrole (DPP)–quaterthiophene copolymers (PDQT) synthesized by the Stille coupling polymerization with Pd(PPh3)2Cl2, Pd2(dba)3/P(o-tol)3, and Pd(PPh3)4 catalyst systems. It was proposed that these structural defects were produced via homocoupling side reactions of the C–Br bonds and the organostannane species. Model Stille coupling reactions further substantiated that the amount of structural defects are catalyst-dependent following the order of Pd(PPh3)2Cl2 > Pd2(dba)3/P(o-tol)3 > Pd(PPh3)4. To verify the structural assignments, “perfect” structurally regular PDQT polymers were prepared using Yamamoto coupling polymerization. When compared to the structurally regular polymers, the polymers containing defects exhibited notable redshifts in their absorption spectra. Surprisingly, the “perfect” structurally regular polymers showed poor molecular ordering in thin films and very low charge transport performance as channel semiconductors in organic thin film transistors (OTFTs). On the contrary, all the “defected” polymers exhibited much improved molecular ordering and significantly higher charge carrier mobility.
- 31 March 2015
- Published by Royal Society of Chemistry (RSC) in Chemical Science
- Vol. 6 (5) , 3225-3235
Open AccessIs a polymer semiconductor having a “perfect” regular structure desirable for organic thin film transistors?
This study utilized high temperature NMR and matrix-assisted laser desorption/ionization time-of-flight (MALDI-ToF) mass spectrometry to reveal that appreciable amounts of structural defects are present in the diketopyrrolopyrrole (DPP)–quaterthiophene copolymers (PDQT) synthesized by the Stille coupling polymerization with Pd(PPh3)2Cl2, Pd2(dba)3/P(o-tol)3, and Pd(PPh3)4 catalyst systems. It was proposed that these structural defects were produced via homocoupling side reactions of the C–Br bonds and the organostannane species. Model Stille coupling reactions further substantiated that the amount of structural defects are catalyst-dependent following the order of Pd(PPh3)2Cl2 > Pd2(dba)3/P(o-tol)3 > Pd(PPh3)4. To verify the structural assignments, “perfect” structurally regular PDQT polymers were prepared using Yamamoto coupling polymerization. When compared to the structurally regular polymers, the polymers containing defects exhibited notable redshifts in their absorption spectra. Surprisingly, the “perfect” structurally regular polymers showed poor molecular ordering in thin films and very low charge transport performance as channel semiconductors in organic thin film transistors (OTFTs). On the contrary, all the “defected” polymers exhibited much improved molecular ordering and significantly higher charge carrier mobility.
- 13 April 2007
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 45 (11) , 2161-2171
Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry investigations of polystyrene and poly(methyl methacrylate) produced by monoacylphosphine oxide photoinitiation
- 13 April 2007
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 45 (11) , 2161-2171
Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry investigations of polystyrene and poly(methyl methacrylate) produced by monoacylphosphine oxide photoinitiation