Yurii V. Bulii
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yurii V. Bulii has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Obodovych
Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine
9 shared publications - Olesya Stepanova
Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine
8 shared publications B.YA. Tselen
Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine
3 shared publications- Vitalii Sydorenko
Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine
3 shared publications - Anna Nedbailo
Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine
2 shared publications - Iaroslav A. Boyarchuk
ТОВ "ЛВН ЛІМІТЕД
2 shared publications
Latest Publications
- 16 April 2026
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 48 (1) , 38-46
ENCHANCEMENT OF TRAY EFFICIENCY IN COLUMN MASS-EXCHANGE APPARATUS
Technological calculations of the column mass–exchange apparatus assume instantaneous transfer of volatile components of vapour and liquid phases, without considering the residence time the liquid on the trays. There is a threshold below which the contact time between the phases is insufficient to reach equilibrium, and as a result, the efficiency of commonly used tray types does not exceed 0.4-0.6. The aim of the work was to study the phase equilibrium between liquid and vapour in the ethanol-water system under subatmospheric pressure; to select appropriate methods for thermodynamic thermodynamic validation of experimental data; to develop approaches for modeling mass transfer between liquid and vapour in cyclic column apparatuses in order to increase tray efficiency; and to evaluate their effectiveness in processing of ethanol–containing fractions under industrial conditions. Research methods included analytical, computational, physicochemical and chromatographic techniques using instruments and methodologies applied in the production of rectified ethanol. The custom-designed experimental apparatus was developed, which allowed to increase the accuracy measurements and reduced the time required to achieve phase equilibrium to 30–40 min. Experimental data on phase equilibrium in the ethanol-water system were obtained in the pressure range of 103 to 50.6 kPa specifically in the low ethanol concentration region (below 3.0 mоl. %), which corresponds to the operation conditions in the lower sections of distillation and rectification columns. Based on the experimental data, phase equilibrium modeling was performed for the specified pressure. The Tsuboko-Katayama equation was used for modeling. Thermodynamic validation of the results demonstrated a satisfactory level of agreement between calculated and experimental data. Phase equilibrium curves were constructed, the relationship between ethanol evaporation coefficients and pressure was established, and the inversion of equilibrium curves was identified. Mass transfer methods between liquid and vapor under controlled cycles of liquid holdup and overflow have been developed, along with designs of mass-exchange apparatus for their implementation. The hydrodynamic operating modes of trays under cyclic conditions have been determined. Experimental results have shown that the extending the contact time between phases on the trays to 30-60 seconds significantly increases the efficiency and reduces steam consumption up to 40%.
- 16 April 2026
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 48 (1) , 38-46
ENCHANCEMENT OF TRAY EFFICIENCY IN COLUMN MASS-EXCHANGE APPARATUS
Technological calculations of the column mass–exchange apparatus assume instantaneous transfer of volatile components of vapour and liquid phases, without considering the residence time the liquid on the trays. There is a threshold below which the contact time between the phases is insufficient to reach equilibrium, and as a result, the efficiency of commonly used tray types does not exceed 0.4-0.6. The aim of the work was to study the phase equilibrium between liquid and vapour in the ethanol-water system under subatmospheric pressure; to select appropriate methods for thermodynamic thermodynamic validation of experimental data; to develop approaches for modeling mass transfer between liquid and vapour in cyclic column apparatuses in order to increase tray efficiency; and to evaluate their effectiveness in processing of ethanol–containing fractions under industrial conditions. Research methods included analytical, computational, physicochemical and chromatographic techniques using instruments and methodologies applied in the production of rectified ethanol. The custom-designed experimental apparatus was developed, which allowed to increase the accuracy measurements and reduced the time required to achieve phase equilibrium to 30–40 min. Experimental data on phase equilibrium in the ethanol-water system were obtained in the pressure range of 103 to 50.6 kPa specifically in the low ethanol concentration region (below 3.0 mоl. %), which corresponds to the operation conditions in the lower sections of distillation and rectification columns. Based on the experimental data, phase equilibrium modeling was performed for the specified pressure. The Tsuboko-Katayama equation was used for modeling. Thermodynamic validation of the results demonstrated a satisfactory level of agreement between calculated and experimental data. Phase equilibrium curves were constructed, the relationship between ethanol evaporation coefficients and pressure was established, and the inversion of equilibrium curves was identified. Mass transfer methods between liquid and vapor under controlled cycles of liquid holdup and overflow have been developed, along with designs of mass-exchange apparatus for their implementation. The hydrodynamic operating modes of trays under cyclic conditions have been determined. Experimental results have shown that the extending the contact time between phases on the trays to 30-60 seconds significantly increases the efficiency and reduces steam consumption up to 40%.
- Open Access
- 1 January 2026
- Published by National Library of Serbia in Acta Periodica Technologica
- No. 00,p. 25
Increasing the radioprotective properties of pectin-containing products from sugar beet pulp through the discrete-pulse energy input principle
Under the conditions of the ongoing war in Ukraine, accompanied by continuous attacks on nuclear facilities, the risks of radioactive contamination by radionuclides have significantly increased, posing a serious threat to human life and public health. One of the approaches to addressing this problem is the use of low-esterified pectin as a dietary supplement, since it performs the function of a radioprotector in the human body and significantly reduces the risks of radiation-related diseases. Sugar beet pulp is currently considered a valuable source of such pectin. The organization of its industrial-scale processing requires the implementation of new energy-efficient equipment as well as the optimization of existing technologies in accordance with modern requirements. In the context of solving this problem, the authors proposed novel heat-and-mass-transfer equipment operating on the principle of discrete-pulse energy input (DPEI), implemented in rotor-pulsation-type equipment. It has been proven that, owing to the processes of dispersion, mixing, heating, dissolution, hydrolysis, and extraction realized in this equipment, it became possible to increase the efficiency of pectin extraction. Optimal process conditions were determined, under which a 97% extraction degree was achieved.
- 1 January 2026
- Published by National Library of Serbia in Acta Periodica Technologica
- No. 00,p. 25
Open AccessIncreasing the radioprotective properties of pectin-containing products from sugar beet pulp through the discrete-pulse energy input principle
Under the conditions of the ongoing war in Ukraine, accompanied by continuous attacks on nuclear facilities, the risks of radioactive contamination by radionuclides have significantly increased, posing a serious threat to human life and public health. One of the approaches to addressing this problem is the use of low-esterified pectin as a dietary supplement, since it performs the function of a radioprotector in the human body and significantly reduces the risks of radiation-related diseases. Sugar beet pulp is currently considered a valuable source of such pectin. The organization of its industrial-scale processing requires the implementation of new energy-efficient equipment as well as the optimization of existing technologies in accordance with modern requirements. In the context of solving this problem, the authors proposed novel heat-and-mass-transfer equipment operating on the principle of discrete-pulse energy input (DPEI), implemented in rotor-pulsation-type equipment. It has been proven that, owing to the processes of dispersion, mixing, heating, dissolution, hydrolysis, and extraction realized in this equipment, it became possible to increase the efficiency of pectin extraction. Optimal process conditions were determined, under which a 97% extraction degree was achieved.
- Open Access
- 1 January 2026
- Published by National Library of Serbia in Acta Periodica Technologica
- No. 00,p. 18
Rational methods of bioethanol production through comprehensive processing of carbohydrate-containing raw feedstock
To stabilize the energy potential of the European Union member states under conditions of increasing oil and fuel prices, the feasibility of increasing the production of bioethanol and technical ethyl alcohol (TEA) from hydrocarbon-containing feedstock has been substantiated. A comparative characterization of ethanol dehydration methods is presented, including azeotropic distillation, water adsorption on molecular sieves, and pervaporation. The specific advantages and disadvantages of each method are identified. An innovative TEA production technology has been developed, the implementation of which enables a 40% reduction in specific steam consumption and a 30% and water for cooling compared to existing conventional methods. A waste-free bioethanol technology has been proposed, which involves the integrated processing of grain-based stillage (the distillers' grains) using a decanter centrifuges and an ultrafiltration unit for removing loose cakes and concentrate the fugate without using a multi-effect evaporator plant. The innovative technology was implemented at the Borok Distillery by the specialists of "Organic" LLC. Its implementation makes it possible to obtain dry distiller's grains (DDGS) with a moisture content of 10-12% and a protein content of 30-35%. Furthermore, it reduces energy consumption in the processing of raw stillage by 40%, process water consumption by 60-70%, and the prime cost of bioethanol by 15%.
- 1 January 2026
- Published by National Library of Serbia in Acta Periodica Technologica
- No. 00,p. 18
Open AccessRational methods of bioethanol production through comprehensive processing of carbohydrate-containing raw feedstock
To stabilize the energy potential of the European Union member states under conditions of increasing oil and fuel prices, the feasibility of increasing the production of bioethanol and technical ethyl alcohol (TEA) from hydrocarbon-containing feedstock has been substantiated. A comparative characterization of ethanol dehydration methods is presented, including azeotropic distillation, water adsorption on molecular sieves, and pervaporation. The specific advantages and disadvantages of each method are identified. An innovative TEA production technology has been developed, the implementation of which enables a 40% reduction in specific steam consumption and a 30% and water for cooling compared to existing conventional methods. A waste-free bioethanol technology has been proposed, which involves the integrated processing of grain-based stillage (the distillers' grains) using a decanter centrifuges and an ultrafiltration unit for removing loose cakes and concentrate the fugate without using a multi-effect evaporator plant. The innovative technology was implemented at the Borok Distillery by the specialists of "Organic" LLC. Its implementation makes it possible to obtain dry distiller's grains (DDGS) with a moisture content of 10-12% and a protein content of 30-35%. Furthermore, it reduces energy consumption in the processing of raw stillage by 40%, process water consumption by 60-70%, and the prime cost of bioethanol by 15%.
- Open Access
- 25 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (4) , 1163-1173
IMPACT OF BIOTECHNOLOGICAL FACTORS ON THE EFFICIENCY OF CORN MASH FERMENTATION IN THE PRODUCTION OF RECTIFIED ETHYL ALCOHOL
The article presents the results of studies on the influence of enzyme preparations, dry yeast, growth activators, and corn grain germs on the synthesis of ethanol and volatile impurities in the production of rectified ethyl alcohol. The research utilized enzyme preparations, dry distiller’s yeast, and activators supplied by leading domestic suppliers. It was established that as the solids content in the mash increased from 24 % to 28 %, the ethanol concentration in the fermentation mash rose by 13–22 % (from 12.4 % to 14.3 % v/v), reaching its highest level when using preparations from LLC “BIOTEST.” At the same time, the content of aldehydes, esters, and methanol in the experimental samples was the lowest. The minimum amount of aldehydes was formed in the fermentation mash with a solids content of 24 %, while the lowest concentration of fusel oils was observed in the wash obtained using preparations from LLC “A-PROFI.” The concentration of methyl alcohol was highest when using preparations from LLC “Novokontakt” and PE “KOUROS.” It was found that removing the grain germ before milling positively affects the qualitative composition of the fermentation mash. Processing raw materials with a lower content of ballast substances reduces the concentration of fusel oils, esters, and ethyl acetate in the fermentation mash, increases ethanol concentration by 7.7–8.9 %, and decreases methanol content by up to 40 %. Further processing of such wash in a distillation-rectification unit allows reducing energy consumption, lowering the production cost of rectified ethyl alcohol, and improving its quality indicators. The use of growth activators during yeast propagation increases ethanol concentration in the wash by 3.8 %, while the content of organic impurities rises insignificantly.
- 25 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (4) , 1163-1173
Open AccessIMPACT OF BIOTECHNOLOGICAL FACTORS ON THE EFFICIENCY OF CORN MASH FERMENTATION IN THE PRODUCTION OF RECTIFIED ETHYL ALCOHOL
The article presents the results of studies on the influence of enzyme preparations, dry yeast, growth activators, and corn grain germs on the synthesis of ethanol and volatile impurities in the production of rectified ethyl alcohol. The research utilized enzyme preparations, dry distiller’s yeast, and activators supplied by leading domestic suppliers. It was established that as the solids content in the mash increased from 24 % to 28 %, the ethanol concentration in the fermentation mash rose by 13–22 % (from 12.4 % to 14.3 % v/v), reaching its highest level when using preparations from LLC “BIOTEST.” At the same time, the content of aldehydes, esters, and methanol in the experimental samples was the lowest. The minimum amount of aldehydes was formed in the fermentation mash with a solids content of 24 %, while the lowest concentration of fusel oils was observed in the wash obtained using preparations from LLC “A-PROFI.” The concentration of methyl alcohol was highest when using preparations from LLC “Novokontakt” and PE “KOUROS.” It was found that removing the grain germ before milling positively affects the qualitative composition of the fermentation mash. Processing raw materials with a lower content of ballast substances reduces the concentration of fusel oils, esters, and ethyl acetate in the fermentation mash, increases ethanol concentration by 7.7–8.9 %, and decreases methanol content by up to 40 %. Further processing of such wash in a distillation-rectification unit allows reducing energy consumption, lowering the production cost of rectified ethyl alcohol, and improving its quality indicators. The use of growth activators during yeast propagation increases ethanol concentration in the wash by 3.8 %, while the content of organic impurities rises insignificantly.
- Open Access
- 25 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (4) , 1191-1198
THE EFFECT OF AERATION ON THE BIOCONVERSION OF CLITORIA TERNATEA L. TEA BY THE CULTURE OF MICROORGANISMS MEDUSOMYCES GISEVII DP-21
Traditional kombucha is produced by fermenting an infusion of black or green tea using a symbiotic culture of bacteria and yeast (SCOBY). According to the classification of microorganisms, this culture is called Medusomyces gisevii. It ferments sucrose and other components of the wort, which can serve as the basis for creating new products with original sensory properties beneficial to human health. The article determines the optimal temperature for extracting Clitoria ternatea L. tea leaves for the preparation of kombucha fermented beverage. It was established that the change in the color of the wort during fermentation is caused by an increase in its acidity and a corresponding change in the coloration of the fermented wort. The influence of aeration during fermentation on the appearance of the drinks was analyzed. The effect of dry matter content, particularly sucrose, on the fermentation process was studied. Changes in titratable acidity during the fermentation of wort under different cultivation conditions were determined. The content of acetic, gluconic, glucuronic, pyruvic, malic, citric, and succinic acids in the fermented wort was identified. The organoleptic profile of the drinks was examined, which confirms the feasibility of aerating the wort during fermentation.
- 25 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (4) , 1191-1198
Open AccessTHE EFFECT OF AERATION ON THE BIOCONVERSION OF CLITORIA TERNATEA L. TEA BY THE CULTURE OF MICROORGANISMS MEDUSOMYCES GISEVII DP-21
Traditional kombucha is produced by fermenting an infusion of black or green tea using a symbiotic culture of bacteria and yeast (SCOBY). According to the classification of microorganisms, this culture is called Medusomyces gisevii. It ferments sucrose and other components of the wort, which can serve as the basis for creating new products with original sensory properties beneficial to human health. The article determines the optimal temperature for extracting Clitoria ternatea L. tea leaves for the preparation of kombucha fermented beverage. It was established that the change in the color of the wort during fermentation is caused by an increase in its acidity and a corresponding change in the coloration of the fermented wort. The influence of aeration during fermentation on the appearance of the drinks was analyzed. The effect of dry matter content, particularly sucrose, on the fermentation process was studied. Changes in titratable acidity during the fermentation of wort under different cultivation conditions were determined. The content of acetic, gluconic, glucuronic, pyruvic, malic, citric, and succinic acids in the fermented wort was identified. The organoleptic profile of the drinks was examined, which confirms the feasibility of aerating the wort during fermentation.
- Open Access
- 3 October 2025
- Published by The Gas Institute of the National Academy of Sciences of Ukraine in Energy Technologies & Resource Saving
- Vol. 84 (3) , 129-137
INFLUENCE OF COMPLEX HYDROMECHANICAL TREATMENT ON THE DISPERSION OF PLANT RAW MATERIAL IN THE TECHNOLOGY OF OBTAINING FUEL ETHANOL
In the energy sector, particularly, the transport sector, biomass of plant origin is associated with additives to motor fuels with biodiesel and bioethanol. The main purpose of the pretreatment of lignocellulosic raw materials for hydrolysis is to destroy the heterogeneous matrix, increase the surface area and porosity of the cellulose material, and free carbohydrates from lignin bonds. One of the key factors affecting the efficiency of pretreatment and subsequent hydrolysis is the size of the raw material particles obtained at the stage of mechanical grinding. During subsequent processing in rotary reactors based on centrifugal pumps, the raw material is subjected to additional influence of thermophysical factors, which contribute to a further increase in the degree of dispersion of the raw material, increasing the specific surface area of the cellulose material. The work aimed to determine the influence of the complex thermophysical phenomena of hydromechanical processing on the particle size of plant raw materials during their pretreatment for hydrolysis in the technology of obtaining fuel ethanol. The feedstock was wheat straw and corn stalks, chopped on a straw cutter, and once processed in a disintegrator. The determination of the plant raw material particle size distribution was carried out using sieve analysis. The processing of the suspension of plant raw materials was carried out on experimental setup with a reactor mixer, which is a rotor-pulsation apparatus. The particle size distribution in the range of 0.001-0.08 mm was determined using a laser particle size analyzer Microsizer 201 A. Further crushing of the straw was carried out on experimental setup. It was determined that with an increase in the solid : liquid ratio from 1 : 5 to 1 : 15, the size of the parts decreases by 35–40 %, and when increasing the solid : liquid ratio from 1 : 5 to 1 : 10 — by 3–5 %. Changing the solid : liquid ratio from 1 : 15 to 1 : 10 for 10 cycles of processing the dispersion in the reactor-mixer until the temperature drops from 47 to 42 °C, at which the productivity of the equipment increases in 1.5–2 times, energy consumption changes by 25–30 %. The temperature of an aqueous dispersion of wheat straw (corn stalk) at a ratio of 1 : 15, mixed in the reactor-mixer for 10 cycles, moves from 17 to 22 °C, at the same time at solid : liquid ratio 1 : 10 at 17 to 42 °С, at solid : liquid ratio 1 : 5 at 17 to 47 °С. When processing an aqueous dispersion with wheat straw in a reactor mixer with a pulsation frequency of 1 kHz, 42 cycles are required to achieve 100 % frequency in less than 80 µm. When the pulsation frequency increases from 1 to 3 kHz, the number of cycles changes to 30. When the pulsation frequency changes from 1 to 5 kHz, the number of cycles decreases to 27. Changing the shear rate of the flow has a more significant effect on particle dispersion than the pulsation frequency. The number of processing cycles is reduced by 5–7 %. Bibl. 15, Fig. 8.
- 3 October 2025
- Published by The Gas Institute of the National Academy of Sciences of Ukraine in Energy Technologies & Resource Saving
- Vol. 84 (3) , 129-137
Open AccessINFLUENCE OF COMPLEX HYDROMECHANICAL TREATMENT ON THE DISPERSION OF PLANT RAW MATERIAL IN THE TECHNOLOGY OF OBTAINING FUEL ETHANOL
In the energy sector, particularly, the transport sector, biomass of plant origin is associated with additives to motor fuels with biodiesel and bioethanol. The main purpose of the pretreatment of lignocellulosic raw materials for hydrolysis is to destroy the heterogeneous matrix, increase the surface area and porosity of the cellulose material, and free carbohydrates from lignin bonds. One of the key factors affecting the efficiency of pretreatment and subsequent hydrolysis is the size of the raw material particles obtained at the stage of mechanical grinding. During subsequent processing in rotary reactors based on centrifugal pumps, the raw material is subjected to additional influence of thermophysical factors, which contribute to a further increase in the degree of dispersion of the raw material, increasing the specific surface area of the cellulose material. The work aimed to determine the influence of the complex thermophysical phenomena of hydromechanical processing on the particle size of plant raw materials during their pretreatment for hydrolysis in the technology of obtaining fuel ethanol. The feedstock was wheat straw and corn stalks, chopped on a straw cutter, and once processed in a disintegrator. The determination of the plant raw material particle size distribution was carried out using sieve analysis. The processing of the suspension of plant raw materials was carried out on experimental setup with a reactor mixer, which is a rotor-pulsation apparatus. The particle size distribution in the range of 0.001-0.08 mm was determined using a laser particle size analyzer Microsizer 201 A. Further crushing of the straw was carried out on experimental setup. It was determined that with an increase in the solid : liquid ratio from 1 : 5 to 1 : 15, the size of the parts decreases by 35–40 %, and when increasing the solid : liquid ratio from 1 : 5 to 1 : 10 — by 3–5 %. Changing the solid : liquid ratio from 1 : 15 to 1 : 10 for 10 cycles of processing the dispersion in the reactor-mixer until the temperature drops from 47 to 42 °C, at which the productivity of the equipment increases in 1.5–2 times, energy consumption changes by 25–30 %. The temperature of an aqueous dispersion of wheat straw (corn stalk) at a ratio of 1 : 15, mixed in the reactor-mixer for 10 cycles, moves from 17 to 22 °C, at the same time at solid : liquid ratio 1 : 10 at 17 to 42 °С, at solid : liquid ratio 1 : 5 at 17 to 47 °С. When processing an aqueous dispersion with wheat straw in a reactor mixer with a pulsation frequency of 1 kHz, 42 cycles are required to achieve 100 % frequency in less than 80 µm. When the pulsation frequency increases from 1 to 3 kHz, the number of cycles changes to 30. When the pulsation frequency changes from 1 to 5 kHz, the number of cycles decreases to 27. Changing the shear rate of the flow has a more significant effect on particle dispersion than the pulsation frequency. The number of processing cycles is reduced by 5–7 %. Bibl. 15, Fig. 8.
- Open Access
- 3 July 2025
- Published by The Gas Institute of the National Academy of Sciences of Ukraine in Energy Technologies & Resource Saving
- Vol. 83 (2) , 69-78
RESEARCH OF THE RHEOLOGICAL INDICATORS OF WATER-OIL EMULSIONS DEPENDING ON THE TECHNICAL EQUIPMENT AND THE TECHNOLOGICAL PARAMETERS OF THEIR PREPARATION
The analysis of the dependence of the density and viscosity of the water-oil emulsion not only on the temperature, the quantitative content of the water phase in it, but also on the technical means and technological parameters of its preparation was carried out. The purpose of the work is to study the changes in the rheological parameters of water-oil emulsions depending on the equipment used and the technological parameters of their preparation. A high degree of dispersion is ensured by hydrodynamic factors and the mechanical effect on the particles of a heterogeneous environment, which consists in impact, shearing and abrasive loads in direct contact of the dispersions with the working elements of the rotor-pulsation device. As the basic model of the rotor-pulsation device, the design of the cylindrical-type apparatus is used, consisting of three coaxially placed cylindrical elements: two stators and a rotor rotating between them. The dependences of the change in the density and viscosity of water-oil emulsion on processing in the rotor-pulsation device at different frequencies of flow pulsations and the number of processing cycles were established. It has been proven that the viscosity of water-oil emulsion depends on the size of the average diameter of the droplets of the dispersed phase (water), which varies depending on the processing parameters. An increase in the number of processing cycles from 1 to 5 at a frequency of flow pulsations from 1 to 4 kHz, depending on the amount of water phase, can increase the viscosity by 1,1–1,8 times. When designing and operating fuel plants, taking into account the preparation of water-oil emulsion in them using rotor-pulsation device, it is necessary to take into account the nature of the change in viscosity depending on the content of the aqueous phase, the number of processing cycles, the frequency of flow pulsations, and the average diameter of particles of the dispersed phase (water). Taking into account the nature of the change in viscosity, it is necessary to make appropriate adjustments to the selection of technological equipment and pipelines, as well as to the technological modes of preparing water-oil emulsion for incineration, or, on the contrary, adjust the viscosity value in relation to the existing equipment. Bibl. 17, Fig. 2, Tab. 4.
- 3 July 2025
- Published by The Gas Institute of the National Academy of Sciences of Ukraine in Energy Technologies & Resource Saving
- Vol. 83 (2) , 69-78
Open AccessRESEARCH OF THE RHEOLOGICAL INDICATORS OF WATER-OIL EMULSIONS DEPENDING ON THE TECHNICAL EQUIPMENT AND THE TECHNOLOGICAL PARAMETERS OF THEIR PREPARATION
The analysis of the dependence of the density and viscosity of the water-oil emulsion not only on the temperature, the quantitative content of the water phase in it, but also on the technical means and technological parameters of its preparation was carried out. The purpose of the work is to study the changes in the rheological parameters of water-oil emulsions depending on the equipment used and the technological parameters of their preparation. A high degree of dispersion is ensured by hydrodynamic factors and the mechanical effect on the particles of a heterogeneous environment, which consists in impact, shearing and abrasive loads in direct contact of the dispersions with the working elements of the rotor-pulsation device. As the basic model of the rotor-pulsation device, the design of the cylindrical-type apparatus is used, consisting of three coaxially placed cylindrical elements: two stators and a rotor rotating between them. The dependences of the change in the density and viscosity of water-oil emulsion on processing in the rotor-pulsation device at different frequencies of flow pulsations and the number of processing cycles were established. It has been proven that the viscosity of water-oil emulsion depends on the size of the average diameter of the droplets of the dispersed phase (water), which varies depending on the processing parameters. An increase in the number of processing cycles from 1 to 5 at a frequency of flow pulsations from 1 to 4 kHz, depending on the amount of water phase, can increase the viscosity by 1,1–1,8 times. When designing and operating fuel plants, taking into account the preparation of water-oil emulsion in them using rotor-pulsation device, it is necessary to take into account the nature of the change in viscosity depending on the content of the aqueous phase, the number of processing cycles, the frequency of flow pulsations, and the average diameter of particles of the dispersed phase (water). Taking into account the nature of the change in viscosity, it is necessary to make appropriate adjustments to the selection of technological equipment and pipelines, as well as to the technological modes of preparing water-oil emulsion for incineration, or, on the contrary, adjust the viscosity value in relation to the existing equipment. Bibl. 17, Fig. 2, Tab. 4.
- Open Access
- 20 March 2024
- Published by The Gas Institute of the National Academy of Sciences of Ukraine in Energy Technologies & Resource Saving
- Vol. 78 (1) , 24-33
TECHNOLOGY AND EQUIPMENT FOR OBTAINING OF UNIVERSAL HYDROCARBON FUEL
An analysis of methods and equipment for obtaining hydrocarbon fuel was carried out. The purpose of the work is the development of technology and heat-mass exchange equipment for the production of universal hydrocarbon fuel, suitable for use in all types of thermal power plants. Heat and mass exchange equipment has been developed, with the help of which it is possible to obtain universal hydrocarbon fuel with a maximum size of coal particles no larger than 3 microns. The use of water-coal suspensions as an energy fuel allows to increase the technical, economic and environmental indicators of power plants. Thus, during the transition to coal-hydrogen fuel, it was possible to increase its thermal capacity from 13.2 to 21.1 MW when 70 % of coal was replaced by coal-hydrogen fuel. Currently, there are various methods and equipment for the preparation of hydrocarbon fuel. However, they all have certain drawbacks. The main disadvantages of the methods of obtaining hydro-coal fuels are multi-stage, metal-intensive, high energy costs, carrying out physico-mechanical and expensive chemical demineralization of coal, etc. Also, the disadvantages are the limited frequency of hydraulic shock pulses during processing in one cycle, which is insufficient when preparing highly concentrated suspensions that meet the requirements for liquid composite fuel intended for direct combustion. In order to improve the quality of the resulting suspension due to more effective grinding and increasing the amount of its solid component, heat and mass exchange equipment was developed, which can be used to obtain universal hydrocarbon fuel for burning in boilers, furnaces, various thermal power equipment, internal combustion engines, etc. As heat and mass exchange equipment, rotary pulsation devices operating according to the method of discrete-pulse energy input were used. Bibl. 18, Fig. 4, Tab. 3.
- 20 March 2024
- Published by The Gas Institute of the National Academy of Sciences of Ukraine in Energy Technologies & Resource Saving
- Vol. 78 (1) , 24-33
Open AccessTECHNOLOGY AND EQUIPMENT FOR OBTAINING OF UNIVERSAL HYDROCARBON FUEL
An analysis of methods and equipment for obtaining hydrocarbon fuel was carried out. The purpose of the work is the development of technology and heat-mass exchange equipment for the production of universal hydrocarbon fuel, suitable for use in all types of thermal power plants. Heat and mass exchange equipment has been developed, with the help of which it is possible to obtain universal hydrocarbon fuel with a maximum size of coal particles no larger than 3 microns. The use of water-coal suspensions as an energy fuel allows to increase the technical, economic and environmental indicators of power plants. Thus, during the transition to coal-hydrogen fuel, it was possible to increase its thermal capacity from 13.2 to 21.1 MW when 70 % of coal was replaced by coal-hydrogen fuel. Currently, there are various methods and equipment for the preparation of hydrocarbon fuel. However, they all have certain drawbacks. The main disadvantages of the methods of obtaining hydro-coal fuels are multi-stage, metal-intensive, high energy costs, carrying out physico-mechanical and expensive chemical demineralization of coal, etc. Also, the disadvantages are the limited frequency of hydraulic shock pulses during processing in one cycle, which is insufficient when preparing highly concentrated suspensions that meet the requirements for liquid composite fuel intended for direct combustion. In order to improve the quality of the resulting suspension due to more effective grinding and increasing the amount of its solid component, heat and mass exchange equipment was developed, which can be used to obtain universal hydrocarbon fuel for burning in boilers, furnaces, various thermal power equipment, internal combustion engines, etc. As heat and mass exchange equipment, rotary pulsation devices operating according to the method of discrete-pulse energy input were used. Bibl. 18, Fig. 4, Tab. 3.
- Open Access
- 15 February 2024
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 46 (1) , 44-52
ENERGY EFFICIENT TECHNOLOGY OF RECTIFIED ETHYL ALCOHOL
In the conditions of rising energy prices, the urgent task for the alcohol industry is the development and implementation of energy-efficient technologies of rectified ethyl alcohol, which allow reducing water and steam consumption and increasing the output of the finished product from a unit of raw materials. To solve it, modernized distillation units (BRU) are being implemented, which work under rarefaction or provide for the heating of some columns by the secondary steam of high potential of other columns operating under pressure, equipping the units with booster and sieving columns, increasing the number of contact devices, using the heat of bard and Luther water , closed column heating, introducing cyclical installations, etc. A promising direction in the creation of energy-efficient technologies is the optimization of the operation of the heat exchange equipment included in the BRU, as well as the use of the heat of secondary steam. One of the factors for optimizing heat exchange equipment is the correspondence of the heat transfer surface of dephlegmators and condensers to their heat load, as well as the methods of their connection to water communication. Also, to optimize the operation of heat exchange equipment, the connection schemes of dephlegmators and vertical condensers of BRU are of great importance. The efficiency of the innovative technology of rectified alcohol has been determined under production conditions, which provides for the supply of alcohol-containing fractions in the form of non-condensed in the deflegmators of the main columns of vapour to the feed plate of the impurity concentration column. This solution allows to reduce the total water consumption by 0,032 m3/dal (5,1 %) and the heating vapour by 1,2 kg/dal (1,9 %) in terms of anhydrous alcohol in comparison with the known method. The expected profit for the plant with a capacity of 3000 dal of alcohol per day will be about UAH 1,5 million per year. Increasing the amount of non-condensed vapour from 2 to 5 % to feed the column will reduce the heating vapour consumption from 10 to 8,8 kg/dal, and increase the profit by 33,3 %. During the tests the qualitative indicators of rectified alcohol corresponded to the normative ones for "Lux" grade.
- 15 February 2024
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 46 (1) , 44-52
Open AccessENERGY EFFICIENT TECHNOLOGY OF RECTIFIED ETHYL ALCOHOL
In the conditions of rising energy prices, the urgent task for the alcohol industry is the development and implementation of energy-efficient technologies of rectified ethyl alcohol, which allow reducing water and steam consumption and increasing the output of the finished product from a unit of raw materials. To solve it, modernized distillation units (BRU) are being implemented, which work under rarefaction or provide for the heating of some columns by the secondary steam of high potential of other columns operating under pressure, equipping the units with booster and sieving columns, increasing the number of contact devices, using the heat of bard and Luther water , closed column heating, introducing cyclical installations, etc. A promising direction in the creation of energy-efficient technologies is the optimization of the operation of the heat exchange equipment included in the BRU, as well as the use of the heat of secondary steam. One of the factors for optimizing heat exchange equipment is the correspondence of the heat transfer surface of dephlegmators and condensers to their heat load, as well as the methods of their connection to water communication. Also, to optimize the operation of heat exchange equipment, the connection schemes of dephlegmators and vertical condensers of BRU are of great importance. The efficiency of the innovative technology of rectified alcohol has been determined under production conditions, which provides for the supply of alcohol-containing fractions in the form of non-condensed in the deflegmators of the main columns of vapour to the feed plate of the impurity concentration column. This solution allows to reduce the total water consumption by 0,032 m3/dal (5,1 %) and the heating vapour by 1,2 kg/dal (1,9 %) in terms of anhydrous alcohol in comparison with the known method. The expected profit for the plant with a capacity of 3000 dal of alcohol per day will be about UAH 1,5 million per year. Increasing the amount of non-condensed vapour from 2 to 5 % to feed the column will reduce the heating vapour consumption from 10 to 8,8 kg/dal, and increase the profit by 33,3 %. During the tests the qualitative indicators of rectified alcohol corresponded to the normative ones for "Lux" grade.
- Open Access
- 11 June 2023
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 49 (2) , 69-76
WASTEWATER TREATMENT OF THERMAL POWER PLANTS (TPP)
An analysis of TPP wastewater, as well as technologies and equipment for their treatment, for choosing a rational mode and determining the maximum permissible concentrations of harmful substances characteristic of the energy industry before discharge into reservoirs was carried out. The compositions of the listed effluents are different and are determined by the type of thermal power plants (TPP) and the main equipment, its capacity, type of fuel, composition of the source water, method of water treatment, etc. For example, water after cooling turbine condensers and air coolers usually carries so-called thermal pollution, since its temperature is 8...10 ºС higher than the temperature of water in the water source. In some cases, cooling water can introduce foreign substances into natural reservoirs. In order to reduce the level of soil and groundwater pollution, local wastewater treatment facilities were constructed at thermal power stations. The second method is the collection of waste water in specially created containers with subsequent purification using sedimentation tanks and filters, which have anthracite or activated carbon as a filter material. TPP waste water is diverse and the chemical composition of each of the effluents is different. Wastewater treatment technology is complex and multi-stage and requires a large amount of various equipment. The ITTF of the National Academy of Sciences has developed a multi-purpose rotor-type aeration and oxidation plant (AORT), which works according to the method of discrete-pulse energy input (DPEI). This installation makes it possible to speed up the rate of heat and mass exchange of chemical reactions in water and water systems by 25-30 %. It makes it possible to reduce the duration of cleaning processes, reduce energy consumption by 2-3 times and consumption of reagents by 20-25 %. The AORT installation is used to clean sewage from iron, manganese, hydrogen sulfide, carbon dioxide, sulfates, and nitrates.
- 11 June 2023
- Published by Institute of Engineering Thermophysics of NAS of Ukraine in Thermophysics and Thermal Power Engineering
- Vol. 49 (2) , 69-76
Open AccessWASTEWATER TREATMENT OF THERMAL POWER PLANTS (TPP)
An analysis of TPP wastewater, as well as technologies and equipment for their treatment, for choosing a rational mode and determining the maximum permissible concentrations of harmful substances characteristic of the energy industry before discharge into reservoirs was carried out. The compositions of the listed effluents are different and are determined by the type of thermal power plants (TPP) and the main equipment, its capacity, type of fuel, composition of the source water, method of water treatment, etc. For example, water after cooling turbine condensers and air coolers usually carries so-called thermal pollution, since its temperature is 8...10 ºС higher than the temperature of water in the water source. In some cases, cooling water can introduce foreign substances into natural reservoirs. In order to reduce the level of soil and groundwater pollution, local wastewater treatment facilities were constructed at thermal power stations. The second method is the collection of waste water in specially created containers with subsequent purification using sedimentation tanks and filters, which have anthracite or activated carbon as a filter material. TPP waste water is diverse and the chemical composition of each of the effluents is different. Wastewater treatment technology is complex and multi-stage and requires a large amount of various equipment. The ITTF of the National Academy of Sciences has developed a multi-purpose rotor-type aeration and oxidation plant (AORT), which works according to the method of discrete-pulse energy input (DPEI). This installation makes it possible to speed up the rate of heat and mass exchange of chemical reactions in water and water systems by 25-30 %. It makes it possible to reduce the duration of cleaning processes, reduce energy consumption by 2-3 times and consumption of reagents by 20-25 %. The AORT installation is used to clean sewage from iron, manganese, hydrogen sulfide, carbon dioxide, sulfates, and nitrates.