SVSubramanyam Venkatachalam

Subramanyam Venkatachalam

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Subramanyam Venkatachalam has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental study of blast wave attenuation using perforated plates and sandwich structures

    by Aldin Justin Sundararaj, Kesavan Marimuthu, Subramanyam Venkatachalam, Anton Savio Lewise Kuzhanthai, Rakhi Aldin, Ajith Raj Rajendran, Levi Reuben Victor Ramasamy, Sneha Gautam

    Blast waves in confined environments generate severe overpressures due to repeated wave reflections, posing significant threats to structures and personnel. Therefore, effective mitigation strategies require experimental evaluation under controlled conditions. In the present study, blast wave attenuation using perforated plates, and hybrid sandwich configurations is investigated experimentally using a shock tube facility. Shock waves with velocities between 500 and 650 m/s were generated using driver pressure ranging from 3 to 12 bar and characterized using high-frequency pressure transducers. Circular and triangular plates with perforation ratios (PR) of 30-50% were examined to assess the influence of perforation geometry and blockage ratio on pressure and velocity attenuation. Results show that blast attenuation increases with blockage ratio and is strongly dependent on perforation shape. Circular perforated plates achieved maximum pressure reduction of approximately 59% at 30% perforation ratio, while triangular perforations resulted in a maximum attenuation of 70% at a perforation ratio of 40%. Among the materials tested, polyurethane foam exhibited the highest attenuation, achieving pressure reductions up to 62% due to its superior energy absorption. Hybrid sandwich configurations combining perforated plates with polyurethane foam further improved blast mitigation, achieving pressure reductions up to 70% along with substantial reductions in transmitted shock velocity.

  • Open Access

    Synergistic Effects of Nanoparticles and Fibers on the Mechanical and Thermal Properties of Epoxy Composites

    by Jain A. R. Tony Benedict, Barath Srinivas Prabakaran, Janardhan Kamath Sreenarayan, Venkatachalam Subramanyam, Muhammed Anaz Khan, Ajith Raj Rajendran

    This study investigates the mechanical and thermal properties of epoxy composites reinforced with aluminum nanoparticles (Al NPs), titanium nanoparticles (Ti NPs), and chopped E-Glass fibers, individually and in hybrid combinations. Thirteen compositions were systematically fabricated and characterized, spanning pure epoxy (PRC0), Al NP-series (PRA1–3), Ti NP-series (PRT1–3), Al NP/E-Glass hybrid series (PRAG1–3), and Ti NP/E-Glass hybrid series (PRTG1–3). The investigation evaluates the effects of these reinforcements on tensile strength, flexural strength, Shore D hardness, thermogravimetric stability, and microstructure. The PRTG2 composite (2 wt% Ti NP + 2 wt% E-Glass fiber) achieved the highest tensile strength of 80 MPa (33.3% improvement over pure epoxy) and the highest flexural strength of 115 MPa (43.75% improvement). These results demonstrate the superior reinforcing efficiency of Ti nanoparticles over Al nanoparticles and the synergistic benefit of combining nanoparticle and fiber reinforcements within a single epoxy matrix.


  • Determination of damage evolution in CFRP subjected to cyclic loading using DIC

    by S. Venkatachalam, S. M. Khaja Mohiddin, H. Murthy

    Damage evolution in carbon fibre reinforced plastic subjected to fatigue loading (R = 0.5, −1, 2) has been studied using digital image correlation to obtain full‐field surface strains. Damage initiation being a local phenomenon, its effect on global parameters is not significant. The local transverse strain is a better indicator of delamination which affects transverse strain more than the longitudinal strain. Variation of normalized local transverse strain (ratio of local transverse strain to applied stress) near the initiated delamination indicates that the damage evolution occurs over 2 to 3 stages. Each stage has a stable damage growth with a drastic increase between the stages. The stages correspond to different damage mechanisms (matrix cracking, fibre‐matrix debonding, delamination, and fibre breakage) dominating at different periods during the fatigue life. Scatter in normalized local transverse strain plots due to large relative displacements was eliminated using different reference images for DIC. Waviness due to shift in the time at which the images are captured during the loading cycles was avoided using a sine curve fit to obtain maximum transverse strain in a cycle. Normalized local transverse strain plots were found to qualitatively reflect the physical extent of damage, thereby providing confidence in the methodology. Fatigue life curves were generated and run‐out lives were determined.