Konrad Kamieniecki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Konrad Kamieniecki has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Janusz Piechna
Warsaw University of Technology, Institute of Aeronautics and Applied Mechanics, Warsaw, Poland
6 shared publications - Krzysztof Kurec
Warsaw University of Technology, Institute of Micromechanics and Photonics, Warsaw, Poland
3 shared publications - Monika Kwacz
Affiliation Warsaw University of Technology, Institute of Micromechanics and Photonics, Warsaw, Poland
2 shared publications - Paweł Borkowski
Warsaw University of Technology
2 shared publications - Sylwester Tudruj
Department of Applied Mechanics, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland
2 shared publications - Adam Piechna
Institute of Automatic Control and Robotics, Warsaw University of Technology, 02-525 Warszawa, Poland
1 shared publication
Latest Publications
- Open Access
- 5 January 2025
- Published by MDPI AG in Electronics
- Vol. 14 (1) , 195
Dynamics Modeling Dedicated to the Operation and Control of Underwater Vehicles
The paper addresses the dynamics modeling of underwater vehicles that are inertia propelled, i.e., they can move based upon the change of the amount of water in their water tanks and the motion of an internal mass, enabling maneuvers. Underwater vehicles of this type can be successfully applied in ocean scientific reconnaissance and exploration missions or for water pollution monitoring. Usually, dynamics modeling methods for them are based upon the Newton–Euler or Lagrange approaches modified to encompass variable mass. The main motivation of this research is to explore other modeling methods and compare them to those traditionally used. In this paper, modeling methods based on the Maggi and Boltzmann–Hamel approaches are presented and discussed with respect to their effectiveness in modeling, operation, and control applications. The resulting comparisons indicate that the traditional approaches are sufficient for the analysis of vehicle operation and performance in the realization of simple tasks; however, they become of limited application when the variable mass or constraints on vehicle dynamics or motion are added or complex maneuvers are required. In this regard, the Maggi or Boltzmann–Hamel approaches are more effective for dynamics modeling. The theoretical development is illustrated by examples of vehicle dynamics developed using the approaches we propose.
- 5 January 2025
- Published by MDPI AG in Electronics
- Vol. 14 (1) , 195
Open AccessDynamics Modeling Dedicated to the Operation and Control of Underwater Vehicles
The paper addresses the dynamics modeling of underwater vehicles that are inertia propelled, i.e., they can move based upon the change of the amount of water in their water tanks and the motion of an internal mass, enabling maneuvers. Underwater vehicles of this type can be successfully applied in ocean scientific reconnaissance and exploration missions or for water pollution monitoring. Usually, dynamics modeling methods for them are based upon the Newton–Euler or Lagrange approaches modified to encompass variable mass. The main motivation of this research is to explore other modeling methods and compare them to those traditionally used. In this paper, modeling methods based on the Maggi and Boltzmann–Hamel approaches are presented and discussed with respect to their effectiveness in modeling, operation, and control applications. The resulting comparisons indicate that the traditional approaches are sufficient for the analysis of vehicle operation and performance in the realization of simple tasks; however, they become of limited application when the variable mass or constraints on vehicle dynamics or motion are added or complex maneuvers are required. In this regard, the Maggi or Boltzmann–Hamel approaches are more effective for dynamics modeling. The theoretical development is illustrated by examples of vehicle dynamics developed using the approaches we propose.
- 20 February 2023
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 70 (2) , 199-218
Mass-Spring System (MSS) 3D simulation of a thin flexible membrane with a new model of the elasticity parameters
Mass Spring Systems (MSS) are often used to simulate the behavior of deformable objects, for example in computer graphics (modeling clothes for virtual characters) or in medicine (surgical simulators that facilitate the planning of surgical operations) due to their simplicity and speed of calculation. This paper presents a new, two-parameter method (TP MSS) of determining the values of spring coefficients for this model. This approach can be distinguished by a constant parameter which is calculated once at the beginning of the simulation, and a variable parameter that must be updated at each simulation step. The value of this variable parameter depends on the shape changes of the elements forming the mesh of the simulated object. The considered mesh is built of elements in the shape of acute-angled triangles. The results obtained using the new model were compared to FEM simulations and the Van Gelder model. The simulation results for the new model were also compared with the results of the bubble inflation test.
- 20 February 2023
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 70 (2) , 199-218
Mass-Spring System (MSS) 3D simulation of a thin flexible membrane with a new model of the elasticity parameters
Mass Spring Systems (MSS) are often used to simulate the behavior of deformable objects, for example in computer graphics (modeling clothes for virtual characters) or in medicine (surgical simulators that facilitate the planning of surgical operations) due to their simplicity and speed of calculation. This paper presents a new, two-parameter method (TP MSS) of determining the values of spring coefficients for this model. This approach can be distinguished by a constant parameter which is calculated once at the beginning of the simulation, and a variable parameter that must be updated at each simulation step. The value of this variable parameter depends on the shape changes of the elements forming the mesh of the simulated object. The considered mesh is built of elements in the shape of acute-angled triangles. The results obtained using the new model were compared to FEM simulations and the Van Gelder model. The simulation results for the new model were also compared with the results of the bubble inflation test.
- Open Access
Towards Balanced Aerodynamic Axle Loading of a Car with Covered Wheels—Inflatable Splitter
Generating aerodynamic downforce for the wheels on the front axle of a car is a much more difficult task than for the rear axle. This paper, submitted to the special issue of Energies “Future of Road Vehicle Aerodynamics”, presents an unusual solution to increase the aerodynamic downforce of the front axle for cars with covered wheels, with the use of an elastic splitter. The effect of the inflatable splitter on the aerodynamic forces and moments was studied in a DrivAer passenger car and a fast sports car, Arrinera Hussarya. Providing that the ground clearance was low enough, the proposed solution was successful in increasing the front axle downforce without a significant increase in drag force. The possibility of emergency application of such a splitter in the configuration of the body rotated by up to 2 degrees with the front end raised was also analyzed. An elastic, deformed splitter remained effective for the nonzero pitch case. The results of the calculations are presented in the form of numerical data of aerodynamic forces, pressure and velocity distributions, and their comparisons. The benefits of the elastic splitter are documented, and the noted disadvantages are discussed.
Open AccessTowards Balanced Aerodynamic Axle Loading of a Car with Covered Wheels—Inflatable Splitter
Generating aerodynamic downforce for the wheels on the front axle of a car is a much more difficult task than for the rear axle. This paper, submitted to the special issue of Energies “Future of Road Vehicle Aerodynamics”, presents an unusual solution to increase the aerodynamic downforce of the front axle for cars with covered wheels, with the use of an elastic splitter. The effect of the inflatable splitter on the aerodynamic forces and moments was studied in a DrivAer passenger car and a fast sports car, Arrinera Hussarya. Providing that the ground clearance was low enough, the proposed solution was successful in increasing the front axle downforce without a significant increase in drag force. The possibility of emergency application of such a splitter in the configuration of the body rotated by up to 2 degrees with the front end raised was also analyzed. An elastic, deformed splitter remained effective for the nonzero pitch case. The results of the calculations are presented in the form of numerical data of aerodynamic forces, pressure and velocity distributions, and their comparisons. The benefits of the elastic splitter are documented, and the noted disadvantages are discussed.
- Open Access
Influence of the Car Movable Aerodynamic Elements on Fast Road Car Cornering
In the case of road cars, road safety is the primary factor. The geometry of high-speed road cars has no regulatory restrictions. In addition to the high engine power and effective shape, they can use various types of additional movable aerodynamic elements to adjust their aerodynamic characteristics to the road conditions. Based on the geometry of a two-seater prototype of such a vehicle, a numerical analysis of the influence of a number of additional movable aerodynamic elements on its aerodynamic characteristics was performed. Several of them were installed on the prototype. An electronic system recording a number of motion parameters of the entire car body and some of its movable elements installed on the body was designed and built. The system has been adapted to program the motion of additional aerodynamic elements according to the set algorithms of their activation, temporarily changing the aerodynamic characteristics of the car. An experimental study of the effect of changes in the aerodynamic characteristics of the prototype on its dynamic properties during a drive through a test road section was carried out. It was shown to what extent an average driver can increase the safe speed of the curve of the road using the possibilities of moving aerodynamic elements installed on it.
Open AccessInfluence of the Car Movable Aerodynamic Elements on Fast Road Car Cornering
In the case of road cars, road safety is the primary factor. The geometry of high-speed road cars has no regulatory restrictions. In addition to the high engine power and effective shape, they can use various types of additional movable aerodynamic elements to adjust their aerodynamic characteristics to the road conditions. Based on the geometry of a two-seater prototype of such a vehicle, a numerical analysis of the influence of a number of additional movable aerodynamic elements on its aerodynamic characteristics was performed. Several of them were installed on the prototype. An electronic system recording a number of motion parameters of the entire car body and some of its movable elements installed on the body was designed and built. The system has been adapted to program the motion of additional aerodynamic elements according to the set algorithms of their activation, temporarily changing the aerodynamic characteristics of the car. An experimental study of the effect of changes in the aerodynamic characteristics of the prototype on its dynamic properties during a drive through a test road section was carried out. It was shown to what extent an average driver can increase the safe speed of the curve of the road using the possibilities of moving aerodynamic elements installed on it.
- Open Access
Influence of Different Plates Arrangements on the Car Body
The purpose of this study was to investigate whether small plates covering the roof and the hood of the DrivAer estate vehicle can be used as airbrakes and increase its drag as well as the downforce. The presented results were obtained with the use of the commercial computational fluid dynamics software ANSYS® Fluent. The main findings of the article are that the aerodynamic devices such as flaps covering surfaces of the vehicle can have a significant impact on drag increase and can be used not only to make the design of the car more striking but also beneficial when utilized as a part of an active aerodynamic setup.
Open AccessInfluence of Different Plates Arrangements on the Car Body
The purpose of this study was to investigate whether small plates covering the roof and the hood of the DrivAer estate vehicle can be used as airbrakes and increase its drag as well as the downforce. The presented results were obtained with the use of the commercial computational fluid dynamics software ANSYS® Fluent. The main findings of the article are that the aerodynamic devices such as flaps covering surfaces of the vehicle can have a significant impact on drag increase and can be used not only to make the design of the car more striking but also beneficial when utilized as a part of an active aerodynamic setup.
- 18 November 2018
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering
- Vol. 21 (15) , 771-779
Design of a resilient ring for middle ear's chamber stapes prosthesis
This paper presents the process of designing a new elastic element replacing a membrane in the chamber stapes prosthesis (ChSP). The results of the study are volume displacement characteristics obtained for the prosthesis and physiological stapes. Simulation tests on a 3D CAD model have confirmed that a properly designed ring can stimulate perilymph with the same or greater efficacy as the physiological stapes footplate placed on the elastic annular ligament. The ChSP with a new elastic element creates a good chance of improving hearing in patients suffering from otosclerosis.
- 18 November 2018
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering
- Vol. 21 (15) , 771-779
Design of a resilient ring for middle ear's chamber stapes prosthesis
This paper presents the process of designing a new elastic element replacing a membrane in the chamber stapes prosthesis (ChSP). The results of the study are volume displacement characteristics obtained for the prosthesis and physiological stapes. Simulation tests on a 3D CAD model have confirmed that a properly designed ring can stimulate perilymph with the same or greater efficacy as the physiological stapes footplate placed on the elastic annular ligament. The ChSP with a new elastic element creates a good chance of improving hearing in patients suffering from otosclerosis.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1965 (1) , 050002
Effect of excitation direction on cochlear macro–mechanics during bone conduction stimulation
In many instances of hearing loss, audiological improvement can be made via direct excitation of a temporal bone (i.e., bone conduction). In order to design better and more efficient devices, the macro-mechanics of the bone conduction hearing pathway must be better understood. Based on previous empirical work, numerical models are useful. In this work, we present results of a time-domain Fluid Structure Interaction model that describes stimulation of the bone conduction pathway. The cochlea was modelled as uncoiled and consisted of an oval window, a round window, a basilar membrane and a helicotrema. In order to monitor pressure waves in the perilymph, the fluid was considered compressible. The excitation, in form of sinusoidal velocity, was applied to the cochlea bony walls. The system was excited in three perpendicular directions: along the basilar membrane, perpendicularly to the membrane and transversely to the membrane. The numerical simulation examined which stimulation direction maximally excited the basilar membrane, the pressure distributions for each excitation direction, and the associated mechanics.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1965 (1) , 050002
Effect of excitation direction on cochlear macro–mechanics during bone conduction stimulation
In many instances of hearing loss, audiological improvement can be made via direct excitation of a temporal bone (i.e., bone conduction). In order to design better and more efficient devices, the macro-mechanics of the bone conduction hearing pathway must be better understood. Based on previous empirical work, numerical models are useful. In this work, we present results of a time-domain Fluid Structure Interaction model that describes stimulation of the bone conduction pathway. The cochlea was modelled as uncoiled and consisted of an oval window, a round window, a basilar membrane and a helicotrema. In order to monitor pressure waves in the perilymph, the fluid was considered compressible. The excitation, in form of sinusoidal velocity, was applied to the cochlea bony walls. The system was excited in three perpendicular directions: along the basilar membrane, perpendicularly to the membrane and transversely to the membrane. The numerical simulation examined which stimulation direction maximally excited the basilar membrane, the pressure distributions for each excitation direction, and the associated mechanics.
- Open Access
- 23 May 2017
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 12 (5) , e0178133
New chamber stapes prosthesis – A preliminary assessment of the functioning of the prototype
Piston-stapedotomy is the most common method for hearing restoration in patients with otosclerosis. In this study, we have experimentally examined a prototype of a new chamber stapes prosthesis. The prototype was implanted in a human cadaver temporal bone. The round window vibrations before and after implantation were measured for the acoustic signal (90 dB SPL, 0.8–8 kHz) in the external auditory canal. In comparison with a 0.4-mm piston prosthesis, the chamber prosthesis induced significantly higher vibration of the round window, especially for frequencies above 1.5 kHz. Based on the results, it can be surmised that stapedotomy with a chamber stapes prosthesis could provide better hearing results in comparison with the piston-stapedotomy.
- 23 May 2017
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 12 (5) , e0178133
Open AccessNew chamber stapes prosthesis – A preliminary assessment of the functioning of the prototype
Piston-stapedotomy is the most common method for hearing restoration in patients with otosclerosis. In this study, we have experimentally examined a prototype of a new chamber stapes prosthesis. The prototype was implanted in a human cadaver temporal bone. The round window vibrations before and after implantation were measured for the acoustic signal (90 dB SPL, 0.8–8 kHz) in the external auditory canal. In comparison with a 0.4-mm piston prosthesis, the chamber prosthesis induced significantly higher vibration of the round window, especially for frequencies above 1.5 kHz. Based on the results, it can be surmised that stapedotomy with a chamber stapes prosthesis could provide better hearing results in comparison with the piston-stapedotomy.
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia IUTAM
- Vol. 24, 48-63
Basilar Membrane Vibration in Time Domain Predicted by Fluid–Structure Interaction Model in Pre- and Post-stapedotomy State
- 1 January 2017
- Published by Elsevier in Procedia IUTAM
- Vol. 24, 48-63
Open AccessBasilar Membrane Vibration in Time Domain Predicted by Fluid–Structure Interaction Model in Pre- and Post-stapedotomy State