RWRyszard Władysiak

Ryszard Władysiak

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ryszard Władysiak has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Effect of Changes in Degassing Parameters on Gasification and Crystallization of EN AC-46000 Alloy

    by T. Szymczak, B.P. Pisarek, P. Just, R. Kaczorowski, G. Gumienny, R. Władysiak, C. Rapiejko

    The paper presents research on the influence of degassing process parameters on the crystallization and gasification of EN AC-46000 alloy (designation according to chemical composition – AlSi9Cu3(Fe)). After melting, the alloy was degassed using Ecosal Al113.S solid refiner and by blowing with an inert gas: nitrogen or argon. Various solid degasser contents and various nitrogen and argon blowing times were used. Thermal and derivative analysis (TDA) were used to study the crystallization process of Al-Si alloy. The density index as well as hydrogen content in the liquid alloy were determined. Using Alu Speed Tester, it was demonstrated that the lowest density index and hydrogen content were obtained in the alloy degassed with the use of Ecosal at a concentration of 1% and then blown with argon for 15 minutes. It has been shown that increasing the efficiency of the degassing process results in prolonging the crystallization time of the tested alloy, and in particular, the crystallization time of αAl + β(Si) binary eutectic. The justification given was the probable removal of small solid particles from the liquid metal, which could form the basis for heterogeneous nucleation of the Al-Si alloy component phases during degassing.


  • Open Access

    The Effect of Sr, Ti, and B on the Crystallization Process and Mechanical Properties of the AlSi9Cu3(Fe) Alloy

    by Tomasz Szymczak, Bogusław Pisarek, Cezary Rapiejko, Ryszard Władysiak, Paweł Just, Rafał Kaczorowski, Grzegorz Gumienny, Bartłomiej Januszewicz, Jarosław Piątkowski, Viktor Sinelnikov, et al.

    This article presents studies on the effect of Sr and TiB on the crystallization process, mechanical properties, hardness, and density index of the Al-Si alloy from the EN AC-46000 group, with a narrowed chemical composition, produced by die-casting and HPDC (high-pressure die casting) technology. The research used the Box–Wilson method to design the experiment and stepwise multiple regression. To identify the optimal amount of Sr and Ti in the analyzed alloy that would simultaneously guarantee the maximization of UTS, YS, Agt, and HBW and the minimization of the DI (density index), multi-criteria optimization was performed. The modifiers were added to the liquid alloy as AlSr10 and AlTi5B1 master alloys. It was found that for 0.02–0.04 wt.% Sr and 0.05–0.08 wt.% Ti in the die castings, the highest mechanical properties, such as UTS, YS, Agt, and HBW (treated as stimulants in the experiment), can be obtained simultaneously with the lowest alloy gasification identified by DI (treated as a destimulant in the experiment). It was also confirmed that the same amount of the above-mentioned elements in HPDC castings caused an increase in UTS by approx. 14%, YS by approx. 6%, A by approx. 47%, and HBW by approx. 13%, with a relatively small increase in DI by approx. 5% compared to the unmodified alloy.


  • Open Access

    Effect of Degassing Parameters on Mechanical Properties of EN AC-46000 Gravity Die Castings

    by Grzegorz Gumienny, Bogusław Pisarek, Tomasz Szymczak, Jakub Gawroński, Paweł Just, Ryszard Władysiak, Cezary Rapiejko, Tadeusz Pacyniak

    The article is devoted to the optimization of the degassing parameters of the AlSi9Cu3(Fe) alloy. The alloy was degassed with a solid degasser (Ecosal) and nitrogen or argon. The variable parameters were time and type of degasser. The test castings were made in permanent molds with an internal diameter of 25 mm and a length of 150 mm. The effect of the degassing time and the amount of degasser on the mechanical properties, as well as the hydrogen content and density index were investigated. The ALU SPEED TESTER developed by FMA was used to test the hydrogen content and the density index. Magmasoft software was used to design the geometry of the test castings. A significant effect of the solid degasser and degassing time on both the density index and the hydrogen content was demonstrated. Replacing nitrogen with argon did not bring any significant improvement in the above-mentioned parameters. The effect of degassing parameters on the mechanical properties of the EN AC-46000 alloy was much less significant, but was still visible. The optimal degassing parameters needed to obtain the highest strength parameters of the EN AC-46000 gravity die castings were determined.


  • Open Access

    Improvement of Artistic Cast Production System

    by R. Władysiak, T. Pacyniak, J. Trzoska

    The paper presents the technology and organization of the artistic cast production. On the basis of the actual cast production system, the manufacturing process was shown, in particular sand–piece moulding, which is a very important process and a time-consuming part of the entire manufacture of the casts. The current state of the production process as well as the organization of the work and production technology were analysed with the use of methods and techniques of production improvement, the Lean Manufacturing concept and computer systems. The results of the analysis and studies were shown with use of schemes and graphs of the layout of the production resources, a flow chart of the production process, value stream mapping, and a costs table for the production and modernization of the moulding stage. The work has shown that there are possibilities to improve the artistic cast production system. This improvement leads to increased productivity, lower production costs of artistic casts and increased competitiveness of the foundry.


  • Open Access

    Analysis of Crystallization Process of Intensive Cooled AlSi20CuNiCoMg Alloy

    by R. Władysiak, A. Kozuń, K. Dębowska, T. Pacyniak

    The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system. The paper presents results of investigation of crystallization process and microstructure of multicomponent synthetic hypereutectic alloy AlSi20CuNiCoMg. The study was conducted for unmodified silumin on the research station allowing the cooling of the special permanent sampler using a program of computer control. Furthermore, the study used a thermal imaging camera to analyze the solidification process of multicomponent alloy. The study demonstrated that the use of mold cooled with water mist stream allows in wide range to form the microstructure of hypereutectic multicomponent silumin. It leads to higher homogeneity of microstructure and refinement of crystallizing phases of casting.


  • Open Access

    The Effect of Water Mist Cooling of Casting Die on the Solidification, Microstructure and Properties of AlSi20 Alloy

    by R. Władysiak, A. Kozuń, T. Pacyniak

    Unmodified AlSi20 alloy were casted at the research station, allowing for sequential multipoint cooling using a dedicated computer- controlled program. This method allows for the formation of the microstructure of hypereutectic AlSi20 alloy and also increases hardness. Primary silicon dendrites were found in the microstructure of cooled samples. Based on these dendrites, the formation of primary silicon particles is explained. Cooling of casting die with a water mist stream causes changes in solidification, which leads to expansion of the boundary layer with columnar crystals and shrinkage of the core zone with equiaxed crystals. It also causes more regular hardness distribution around pre-eutectic Si crystals, which can lead to tensile strength and machinability improvement.


  • Open Access

    Effect of Casting Die Cooling on Solidification Process and Microstructure of Hypereutectic Al-Si Alloy

    by R. Władysiak, A. Kozuń, T. Pacyniak

    The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system. The paper presents results of investigation of crystallization process and microstructure of synthetic hypereutectic alloys: AlSi15 and AlSi19. Casts were made in permanent mold cooled with water mist stream. The study was conducted for unmodified silumins on the research station allowing the cooling of the special permanent probe using a program of computer control. Furthermore the study used a thermal imaging camera to analyze the solidification process of hypereutectic silumins. The study demonstrated that the use of mold cooled with water mist stream allows in wide range the formation of the microstructure of hypereutectic silumins. It leads to higher homogeneity of microstructure and refinement of crystallizing phases and also it increases subsequently the mechanical properties of casting.


  • Open Access

    Examining the Possibilities of Analyzing the Solidification Process of Al-Si Alloy with the Infrared Camera

    by R. Władysiak, A. Kozuń, T. Pacyniak

    The paper presents the results of the crystallization process of silumin by the TDA thermographic method and the results of the cast microstructure obtained in the sampler ATD-10, that was cooling down in ambient air. The study was conducted for silumins AlSi8 and AlSi11 unmodified. The work demonstrated that the use of thermal imaging camera allows for the measurement and recording the solidification process of silumin. Thermal curve was registered with the infrared camera and derivative curve that was calculated on the base of thermal curve have both a very similar shape to adequate them TDA curves obtained from measurements using a thermocouple. Test results by TDA thermographic method enable quantitative analysis of the kinetics of the cooling and solidification process of hypo-and neareutectic silumins.