MAMisarah Abdelaziz

Misarah Abdelaziz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Misarah Abdelaziz has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Approaching Terminal-Velocity of Large Firebrands for Extreme Fire Events

    by Fabian Brännström, Misarah Abdelaziz, Ha-Ninh Nguyen, Alexander Filkov, Andrew L. Sullivan, Jean-Baptiste Filippi

    Wildfire spread on a large scale is heavily driven by the transport of firebrands, as it leads to short- and long-range spotting. Detailed knowledge of terminal velocity can help predict firebrand transport and therefore overall wildfire spread modelling. The current work evaluates an approach to estimating terminal velocity based on CFD simulations with a detailed firebrand shape and assesses its impact on orientation. For the selected firebrand and simulation setup, a range of terminal velocities of approximately 5 to 11 m/s is calculated. This is based on 352 RANS simulations for one particular detailed firebrand at 11 different orientations and two turbulence models, with varying inlet velocities and two mesh refinements. DES and LES turbulence models are considered as a next step for a detailed comparison with wind tunnel measurements.

  • Open Access

    Toward Remote Sensing of Wildland Fuel Combustibility: A Pilot Study Evaluating an Experimental Method to Link Fuel Spectral Reflectance with Fire Behaviour and Emissions

    by Andrew L. Sullivan, Nicolas Younes, Christopher T. Roulston, Courtney Bright, Fabienne Reisen, Eric Hay, Andy Allen, Matt P. Plucinski, Misarah A. Abdelaziz, Marek Tuhý, et al.

    While remote sensing has been widely used to estimate vegetation biochemical and structural properties, relatively little work has systematically and experimentally linked vegetative fuel spectral reflectance to independently measured fuel combustibility, free-spreading fire behaviour, and fire emissions. This limits the development and validation of remote sensing products for operational wildland fire applications. We present a pilot-study evaluation of an experimental method that integrates imaging spectroscopy with free-spreading fires in a combustion wind tunnel to investigate relationships between wildland fuel spectral reflectance and combustibility, fire behaviour, and fire emissions. The pilot study used three common Australian fuels at two combustibility levels. Pre- and post-burn imaging spectroscopy observations (400–2500 nm) were collected during 26 experiments, alongside measurements of fuel biochemistry, calorimetry, moisture, rate of spread, combustion efficiency, and gaseous and particulate emissions. Statistically significant differences between fuel type and combustibility were found in fuel moisture, rate of spread, and emissions, with corresponding differences evident in the spectral signatures. Partial least squares regression (PLSR) indicated that pre-fire spectral information was informative for predicting several fire behaviour and emissions metrics. These results demonstrate the feasibility of the proposed methodology and provide a foundation for extending it to a wider range of wildland fuels. Data generated using this methodology have the potential to improve interpretation of remote sensing datasets and inform the design of future satellite instruments, with potential applications in assessing fuel condition, predicting fire behaviour, and estimating wildland fire emissions.

  • Open Access

    Comprehensive methodology for tracking burning firebrands in a vertical wind tunnel using multi-view video analysis

    by Misarah Abdelaziz, Andrew. L. Sullivan

    Background: Burning debris (firebrands) can potentially travel significant distances to ignite spot fires many kilometres downwind of a wildfire, posing substantial challenges for fire spread prediction and management. Aim: To improve our understanding of the combustion and flight behaviours of common bark firebrands through better quantification and detailed analysis of their motion, combustion and aerodynamic behaviour. Methods: A custom firebrand tracking system consisting of three synchronised video cameras positioned orthogonally around the working section of a vertical wind tunnel was built and bespoke image processing algorithms developed to automatically reconstruct the 3D trajectory and combustion behaviour of a bark sample. Key results: The system was found to accurately estimate bark sample position as well as spatial velocity, orientation changes and burnout profile. Conclusions: A robust and accurate methodology to track the dynamic trajectory and behaviour of untethered burning bark falling at its terminal velocity was developed that overcomes many of the limitations of previous tracking approaches. Implications: This study, applicable to a broad range of bark species as well as other firebrand materials under varying conditions, enables the development of more accurate predictive models of firebrand transport that will help improve the simulation and prediction of spotting in wildfires.


  • Long distance spotting potential of Messmate stringybark

    by Alberto Alonso Pinar, Misarah Abdelaziz, Jane Cawson, Jean Baptiste Filippi, Alexander Filkov

    Background. Messmate stringybark (Eucalyptus Obliqua, L’Her) is notorious for causing mass spotting near the fire front and up to several kilometres ahead. However, its contribution to longer distance spotting (5-30 kms ahead of the fire) is unclear. Messmate is widespread in the forests of southeastern Australia making the study of its spotting potential particularly important. Aim. This study seeks to quantify the intermediate and long-distance spotting potential of large Stringybark firebrands by examining how firebrand size influences terminal velocity and burnout time. Methods. Firebrand samples of three lengths (10, 15 and 20cm) were introduced to a vertical wind tunnel and ignited at one end or across the entire outer layer. Combustion time and burnout mass were measured. Key results. No strong correlation was found between firebrand length, sap content, or ignition method and flameout time. Extended burnout times exceeding 200 seconds were recorded in 11% of the samples, with reflaming observed in 35% of all samples. Conclusions. Messmate has the potential to cause spotting up to several kilometres but spotting beyond 10km is unlikely. Implications. Spotting models can assume spotting distances of less than 10 km for stringybark eucalypts.


  • On predictive models for the equivalent sand grain roughness for wall-bounded turbulent flows

    by Misarah Abdelaziz, L. Djenidi, Mergen H. Ghayesh, Rey Chin

    One of the long-standing goals of rough wall fluid dynamics research is to determine the drag penalty of surfaces based solely on their topographical parameters. The most important length scale or roughness parameter that best describes a surface in relation to friction drag has not been agreed upon yet, despite the many studies that, over the years, have attempted to identify the most appropriate surface parameter. The concept of an equivalent sand-grain roughness (ks) was introduced to standardize different types of roughness in wall-bounded turbulence, serving as an input parameter for predicting the roughness function ΔU+. To anticipate ΔU+ generated by a rough surface under turbulent flow conditions, experts use roughness correlations that establish a correspondence between the topographical characteristics of the surface and ks. Therefore, a chronological compilation of roughness correlations is presented, detailing the parameter ranges and types of roughness used in their development. This study evaluates the effectiveness of predictive correlation functions and aims to formulate a universal function by exploring a comprehensive assortment of three-dimensional (3D) surface textures available in the literature. The results suggest that a correlation based on surface height skewness (ksk) and streamwise effective slope (ESx) can predict the ratio (ks/kq), where kq is the root mean square roughness height for 3D roughness in the fully rough regime. Despite the fact that the correlation is restricted to 3D surface roughness, which is a more realistic representation, the model demonstrated a high level of accuracy in predicting ks for over 120 distinct rough surfaces.


  • Open Access

    Influence of skewed three-dimensional sinusoidal surface roughness on turbulent boundary layers

    by Misarah Abdelaziz, L. Djenidi, Mergen H. Ghayesh, Rey Chin

    The impact of roughness skewness (ksk) on turbulent boundary layer (TBL) flow with a zero pressure gradient over three-dimensional (3D) sinusoidal rough surfaces was experimentally investigated using a single hotwire anemometer. Nine 3D sinusoidal profiles were manufactured with positive, negative, and zero roughness skewness values. Measurements were taken at three different freestream velocities for each surface and compared with smooth wall TBL results. This study covered a range of friction Reynolds numbers (Reτ) from approximately 1000 to 4000, with δ/k≈20 ± 2, where δ represents the local boundary layer thickness, and k is the maximum height of the roughness, measured from the valley to peak. The results indicate that the wall-unit normalized streamwise mean velocity profiles for all rough surfaces exhibit a downward shift compared to the smooth wall profiles. Surfaces with positive roughness skewness produced the highest drag, leading to the largest downward shift. The friction coefficient (Cf) decreased as ksk decreased. The percentage increase in Cf and ΔU+ (the roughness function) was much larger when moving from negative to zero roughness skewness than when moving from zero to positive roughness skewness. The small differences in turbulence intensity profiles and higher-order turbulence statistics in the outer region of the TBL support the outer layer similarity hypothesis for the roughness considered in this study. The autocorrelation study revealed that surfaces with positive roughness skewness tend to shorten the average length of turbulence structures in the near-wall region.


  • Open Access

    On the effect of streamwise and spanwise spacing to height ratios of three-dimensional sinusoidal roughness on turbulent boundary layers

    by Misarah Abdelaziz, Lyazid Djenidi, Mergen H. Ghayesh, Rey Chin

    A developing zero pressure gradient (ZPG) turbulent boundary layer (TBL) over different three-dimensional (3-D) sinewave roughnesses is investigated experimentally using single hot-wire anemometry. Seven different sinewave profiles are fabricated with the same amplitude and with different wavelengths in the streamwise (sx) and spanwise (sz) directions. The effects of varying sx and sz on turbulence statistics and the drag coefficient (Cf) are assessed. The wall-unit normalised streamwise mean velocity profile is shifted downwards compared with the smooth wall profile for all roughnesses. The streamwise spacing to height ratio sx/k has a more significant effect on the roughness function ΔU+ and Cf compared with the spanwise spacing to height ratio sz/k. However, sz/k has a large impact on the streamwise turbulence intensities in the log and outer layer. An excellent collapse is observed among the mean streamwise velocity profiles plotted in defect form in the outer region. However, a lack of similarity between TBLs over different rough surfaces is observed in the outer region for the turbulenceintensities profiles. For isotropic 3-D sinusoidal roughness (equal streamwise and spanwise spacing to height ratios), the contours of premultiplied streamwise turbulent energy spectrograms show an increase of energy in the outer layer with increasing spacing to height ratios. For anisotropic 3-D sinusoidal roughness (unequal streamwise and spanwise spacing to height ratios), the contours of premultiplied streamwise turbulent energy spectrograms show an increase of energy in the outer layer with increasing sz/sx from half to two in this study.


  • A new equivalent sand grain roughness relation for two-dimensional rough wall turbulent boundary layers

    by Misarah Abdelaziz, L. Djenidi, Mergen H. Ghayesh, Rey Chin

    The effects of different geometries of two-dimensional (2-D) roughness elements in a zero pressure gradient (ZPG) turbulent boundary layer (TBL) on turbulence statistics and drag coefficient are assessed using single hot-wire anemometry. Three kinds of 2-D roughness are used: (i) circular rods with two different heights, $k= 1.6$ and 2.4 mm, and five different streamwise spacing of $s_{x}= 6k$ to $24k$ , (ii) three-dimensional (3-D) printed triangular ribs with heights of $k= 1.6$ mm and spacing of $s_{x}= 8k$ and (iii) computerized numerical control (CNC) machined sinewave surfaces with two different heights, $k= 1.6$ and 2.4 mm, and spacing of $s_{x}= 8k$ . These roughnesses cover a wide range of ratios of the boundary layer thickness to the roughness height ( $23 < \delta /k < 41$ ), where $\delta$ is the boundary layer thickness. All roughnesses cause a downward shift on the wall-unit normalised streamwise mean velocity profile when compared with the smooth wall profiles agreeing with the literature, with a maximum downward shift observed for $s_{x}= 8k$ . In the fully rough regime, the drag coefficient becomes independent of the Reynolds number. Changing the roughness height while maintaining the same spacing ratio $s_{x}/k$ exhibits little influence on the drag coefficient in the fully rough regime. On the other hand, the effective slope $(ES)$ and the height skewness $(k_{sk})$ appear to be major surface roughness parameters that affect the drag coefficient. These parameters are used in a new expression for $k_{s}$ , the equivalent sand grain roughness, developed for 2-D uniformly distributed roughness in the fully rough regime.