Alexandra Rybová
Research Subjects
Alexandra Rybová has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Anežka Zezulová
Research Institute of Building Materials
5 shared publications - Martin Boháč
Research Institute of Building Materials
3 shared publications - Theodor Staněk
Research Institute for Building Materials, Brno, Czech Republic
3 shared publications - Dana Kubátová
Research Institute for Building Materials, Brno, Czech Republic
2 shared publications - Radovan Nečas
Research Institute for Building Materials, Hněvkovského 30/65, Brno 617 00
2 shared publications - Eva Bartoníčková
Brno University of Technology, Faculty of Chemistry, Institute of Materials Science, Purkyňova 464, 612 00 Brno, Czech Republic
1 shared publication
Latest Publications
- 1 June 2024
- Published by Springer Nature
- p. 245-252
Combined Effect of Sulfur and Lithium on Intensification of Portland Cement Clinker Burning
- 1 June 2024
- Published by Springer Nature
- p. 245-252
Combined Effect of Sulfur and Lithium on Intensification of Portland Cement Clinker Burning
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 3-8
Hydraulic Binder from Hazardous Waste
Since asbestos has been classified as a hazardous chemical, it is desirable to propose a practical and safe procedure for the disposal of asbestos-cement products, or even better to re-use them. In this work, the temperature conditions of degradation of samples of various types of asbestos and products containing asbestos were examined. Samples were burnt at different temperatures and monitored by XRD, DTA, light and electron microscopy. By evaluation of changes at different burning temperatures, the previous findings on the decomposition of asbestos minerals have been confirmed. It has been found that the burning of asbestos cement materials alone or with the addition of limestone at the temperature above 1100 °C leads to the decomposition of hazardous asbestos and, with or without the addition of a setting regulator, hydraulic binder is formed with technological parameters suitable for the building industry.
- 20 June 2018
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 276, 3-8
Hydraulic Binder from Hazardous Waste
Since asbestos has been classified as a hazardous chemical, it is desirable to propose a practical and safe procedure for the disposal of asbestos-cement products, or even better to re-use them. In this work, the temperature conditions of degradation of samples of various types of asbestos and products containing asbestos were examined. Samples were burnt at different temperatures and monitored by XRD, DTA, light and electron microscopy. By evaluation of changes at different burning temperatures, the previous findings on the decomposition of asbestos minerals have been confirmed. It has been found that the burning of asbestos cement materials alone or with the addition of limestone at the temperature above 1100 °C leads to the decomposition of hazardous asbestos and, with or without the addition of a setting regulator, hydraulic binder is formed with technological parameters suitable for the building industry.
- Open Access
- 1 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 379 (1) , 012010
Properties of mixtures of cement with various raw materials
This paper presents possibility of utilization of selected Czech and Slovak industrial and natural raw materials in blended cement production. The cement blends were prepared using 75 wt. % of cement and 25 wt. % of a substituent. The paper is focused only on test results of the laboratory-prepared blended cements. The influence of admixture on hydration process was observed by calorimetric measurement of heat evolution during hydration process within 24 hours. The hydration products of water-cured samples for 28 days were determined by thermal analysis. Further properties, such as short and long-term compressive strengths and setting period, were determined.
- 1 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 379 (1) , 012010
Open AccessProperties of mixtures of cement with various raw materials
This paper presents possibility of utilization of selected Czech and Slovak industrial and natural raw materials in blended cement production. The cement blends were prepared using 75 wt. % of cement and 25 wt. % of a substituent. The paper is focused only on test results of the laboratory-prepared blended cements. The influence of admixture on hydration process was observed by calorimetric measurement of heat evolution during hydration process within 24 hours. The hydration products of water-cured samples for 28 days were determined by thermal analysis. Further properties, such as short and long-term compressive strengths and setting period, were determined.
- Open Access
- 1 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 379 (1) , 012008
Thermal behaviour of inorganic aluminosilicate polymer based on cement kiln dust
Alkali activated materials have shown potential for use in high temperature applications. This paper deals with thermal behaviour of various inorganic polymer formulations, which were prepared by mixing metakaolin, blast furnace slag, fly ash and cement kiln dust as alkaline activator. The cement kiln dust was added in the amount of 10 wt.%. The influence of thermal treatment ranging from 30 to 1000°C on the following characteristics was evaluated: compressive strength, thermal expansion, weight loss, melting point, morphology changes and dehydration. The thermal behaviour was studied by TG-DTA analysis, dilatometry and heating microscope, XRD analysis was used to examine phase changes. All measurements were conducted on samples after 28 days of curing time.
- 1 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 379 (1) , 012008
Open AccessThermal behaviour of inorganic aluminosilicate polymer based on cement kiln dust
Alkali activated materials have shown potential for use in high temperature applications. This paper deals with thermal behaviour of various inorganic polymer formulations, which were prepared by mixing metakaolin, blast furnace slag, fly ash and cement kiln dust as alkaline activator. The cement kiln dust was added in the amount of 10 wt.%. The influence of thermal treatment ranging from 30 to 1000°C on the following characteristics was evaluated: compressive strength, thermal expansion, weight loss, melting point, morphology changes and dehydration. The thermal behaviour was studied by TG-DTA analysis, dilatometry and heating microscope, XRD analysis was used to examine phase changes. All measurements were conducted on samples after 28 days of curing time.
- 11 December 2017
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 133 (1) , 399-404
Application of dilatometric analysis to the study of autoclaved calcium silicate materials
- 11 December 2017
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 133 (1) , 399-404
Application of dilatometric analysis to the study of autoclaved calcium silicate materials